American Standard Jasmine 3821.834 User manual
- Category
- Sanitary ware
- Type
- User manual
HI-FLOW
KITCHEN FAUCET
Installation
Instructions
Certified to comply with ANSI A112.18.1M
M968150 REV. 1.1
3821.831
3821.834
1
This faucet permits an interchangeable mounting of each integral
component -- spout, valve, and hand spray -- to suit the particular
installation requirements.
Remove LOCKNUT (1) and RETAINER PLATE (2).
Insert SUPPLY TUBES
(3), SPOUT HOSE (4) and
THREADED STUD
(5) through hole in SINK.
Make sure O-RING
(6) is properly seated in recess of BASE.
Orient VALVE
(7) so that two inlets tubes face towards the front.
Assemble RETAINER PLATE
(2) and LOCKNUT (1) onto
STUD
(5) from underside of SINK.
Hand tighten LOCKNUT
(1) and check that rotation of HANDLE
from HOT to COLD is centered. Secure VALVE
(7) position by
tightening LOCKNUT
(1) firmly. (Spread TUBES for better
access to LOCKNUT).
Bend TUBES
(3) to meet supplies. Use palm of hand to support
TUBES
(3) while bending to avoid kinking.
Before starting installation, place each component loosely
into the holes of the kitchen sink to select the most desirable
arrangement.
ROUGHING-IN DIMENSIONS
9-3/8
8-5/8
13
1-1/16
MAX
1-1/4 MAX
1-1 /4 MAX
13/16
DIA
HOT COLD
3/8 OD COPPER
BENDABLE
C/L OF
FLEXIBLE HOSE
TO SPOUT
SPRAY
HOSE
VALVE
1-1/4
MIN. DIA
MTG HOLE
2 DIA.
7-1/8
10 MAX
2-1/2
DIA.
MTG
SURFACE
27/32
DIA.
2 DIA.
10" MAX
VALVE INSTALLATION
SPRAY HOSE
SPOUT HOSE
SINK
1
2
3
4
5
6
7
0
1
2
3
4
5
6
Thank you for selecting American-Standard...
the benchmark of fine quality for over 100 years.
To ensure that your installation proceeds smoothly--
please read these instructions carefully before you begin.
TOOLS REQUIRED
Plumbers' Putty or Caulking
Adjustable WrenchChannel Locks Regular Screwdriver
Phillips ScrewdriverPhillips Screwdriver
Turn off water at
main supply.
CAUTION
4
2
SPOUT INSTALLATION
3
SERVICE
5
6
AERATOR may accumulate dirt causing distorted and reduced water flow. Remove AERATOR and rinse clean.
If SPOUT drips, operate handles several times from OFF to ON position. Do not force - handle.
HAND SPRAY INSTALLATION
Make sure RUBBER RING
(2)
is properly seated in recess
of ESCUTCHEON
(3).
Center SPOUT ESCUTCHEON (3)
and tighten WING NUT(4) firmly.
Connect SPOUT HOSE (5)
to SPOUT SHANK (1). (SPOUT
HOSE is connected to
VALVE BODY already).
Place SPRAY HOLDER
(1)
into separate hole of SINK
and assemble WING NUT
(2) onto SHANK from
underside of SINK and
tighten.
Feed SPRAY HOSE (3)
through HOLDER (1)
and attach COUPLING
(4) to THREADED
STUD of VALVE.
Tighten COUPLING
NUT
(4) firmly.
Make certain that SPACER WASHER
(5) and
RUBBER WASHER
(6) are attached to SPRAY
HOSE
(3) and thread SPRAY HEAD (7) to NUT (8).
Insert SPOUT SHANK (1)
through sink hole.
TEST INSTALLED FAUCET
Move handle down into "off" position, remove AERATOR.
With HANDLE in "off" position, turn on water supplies
and check all connections for leaks.
Operate handle up and down, in COLD and HOT positions,
to flush water lines thoroughly and check spout mounting
for leaks.
Direct SPRAY HEAD into sink. Open faucet and activate
spray. Check SPRAY HOSE connections for leaks.
Move handle down into "off" position and replace AERATOR.
Bend TUBES to meet supplies. Use palm of hand to support TUBES
while bending to avoid kinking.
Connect 3/8-inch OD inlet TUBES to water supplies with appropriate connectors.
Connect LEFT tube to HOT water supply and RIGHT tube to COLD.
CONNECT SUPPLIES
OR
Note: For installation less spray, cap off
THREADED STUD with PIPE CAP.
1
1
SPRAY HOSE
2
2
3
3
4
4
5
5
6
7
8
M968150 REV. 1.1
6
PRY RED RING FORWARD
AND ROTATE COUNTER-
CLOCKWISE ONE CLICK
PRY RED RING FORWARD
AND ROTATE CLOCKWISE
"A"
ADJUSTMENT WHEN
WATER IS TOO HOT
"A"
"A"
"B"
ADJUSTMENT WHEN
WATER IS TOO COLD
"B"
"RED RING"- HOT
LIMIT SAFETY STOP
TEMPERATURE
SETTING NUMBERS
0
1
2
3
4
5
6
5
By restricting handle rotation and limiting the amount of hot water allowed
to mix with the cold, the HOT LIMIT SAFETY STOP reduces risk of accidental
scalding. To set the maximum hot water temperature of your faucets, all you
need to do is adjust the setting on the HOT LIMIT SAFETY STOP.
Remove HANDLE BUTTON (1) and loosen SET SCREW (2). Pull
HANDLE (3) off valve stem. Pull off CAP (4). Use a flat blade
screwdriver or your fingers to pull up and rotate red
HOT LIMIT SAFETY STOP (5). Follow Step "A" or "B" to adjust
min./max.discharge temperature. "0" being the hottest to
"7" the coldest temperature setting. Factory set at "0".
Replace ESCUTCHEON CAP (4), HANDLE (3), tighten
HANDLE SCREW (1) and install INDEX BUTTON (2).
HOT LIMIT SAFETY STOP ADJUSTMENT
"B"
-
1
-
2
American Standard Jasmine 3821.834 User manual
- Category
- Sanitary ware
- Type
- User manual
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
American Standard Ceramix 2021.831 User manual
-
American Standard 4205.000.F15.002 User manual
-
-
-
-
-
-
-
-