RGBlink DXP D0808 Quick start guide

DXP D0808 Quick Start

VIEWSIZE THE WORLD

 Support any in any out

 Support independent output switching

 Support hot backup

 Support infrared remote control

 Can read and store up to 24/36 user

scenarios

 Automatically recognize the formats

 Support EDID management

Address：S603-604 Weiye Building Torch Hi-Tech Industrial Development Zone Xiamen, Fujian Province, P.R.C

Tel: 00865925771197 Fax: 00865925771202

Email: s[email protected] http://www.rgblink.cn

1

CONTENT

Product Introduction ............................................................................................................................... 2

Packing Configuration ............................................................................................................................ 3

Hardware Orientation .............................................................................................................................. 4

Front Panel ......................................................................................................................................... 4

Back Panel ......................................................................................................................................... 5

Operating Instruction .............................................................................................................................. 6

Content ............................................................................................................................................... 6

How to Switch between Input and Output Channel .................................................................... 7

How to Switch One Input to all Outputs ...................................................................................... 7

How to Read Device Status ........................................................................................................ 8

How to Set LOGO Display when Power on ................................................................................ 8

How to Set the EDID ................................................................................................................... 8

How to Set the Language ........................................................................................................... 9

How to Realize Cascade Setting ................................................................................................ 9

How to Set the Machine Address ................................................................................................ 9

How to Realize Signal Auto Take .............................................................................................. 10

How to Lock the Front Panel .................................................................................................... 10

How to Realize Hot Backup ...................................................................................................... 10

How to Save the Preset Input and Output Channel ................................................................. 11

How to Load the Saved Input and Output Channel .................................................................. 11

How to Reset the Factory Settings ........................................................................................... 11

Contact Information............................................................................................................................... 12

Address：S603-604 Weiye Building Torch Hi-Tech Industrial Development Zone Xiamen, Fujian Province, P.R.C

Tel: 00865925771197 Fax: 00865925771202

Email: s[email protected] http://www.rgblink.cn

2

Product Introduction

RGBlink strong technical strength determines

the high quality of AVDXP series matrix

switchers. We choose the chips with best

performance, elaborate design for every way

of switchers, to ensure the high quality of

switchers. After rigorous testing,

3G/HD/SD-SDI video signal, optical signal

transmission rate are 2.97Gbps, DVI switchers

signal bandwidth is 2.5 GHz, support HD

digital signal input. VGA switching signal

bandwidth is 450 MHz (-3 db), support

resolution of 2048×1536@60Hz and 1024×

768@120Hz, composite video bandwidth for

100 M (-3 db), fully meet various strict

requirements and high quality occasions.

Products in this series are widely used in large

screen projection display engineering,

electronic teaching, command and control

center, multimedia meetings room, etc.

Switches in this series are equipped with

monochromatic LCD, RS-232 communication

interface, RS422 communication interface

(optional), with outage protect function, can

read and store up to 100 user scenarios, and

special matching control software, can in

conjunction with computer, remote control

system or all kinds of distal control equipment

(such as center console system). The system

is equipped with multiple sets of serial

instructions, compatible with mainstream

matrix of serial instruction set.

System Connection

RGBlink offers solutions to

demanding technical problems.

Any application questions, or

required further information,

please contact with our

customer Support Engineers.

DXP D0808 System Connection Diagram

Address：S603-604 Weiye Building Torch Hi-Tech Industrial Development Zone Xiamen, Fujian Province, P.R.C

Tel: 00865925771197 Fax: 00865925771202

Email: s[email protected] http://www.rgblink.cn

3

Packing Configuration

Note: Chinese Standard, American Standard or European Standard power cord is option.

The color of the screw driver is randomly when packing.

Power Cord

9-pin Serial

Cable

USB Disk

DVI 转 HDMI 线

Antistatic Bag

防静电袋

Screw Driver

Certification

Address：S603-604 Weiye Building Torch Hi-Tech Industrial Development Zone Xiamen, Fujian Province, P.R.C

Tel: 00865925771197 Fax: 00865925771202

Email: s[email protected] http://www.rgblink.cn

4

Hardware Orientation

Front Panel

Button Instruction

1~8

Selection button for input and

output channel, and number

choice of save or call saving

modes

LOAD

Load button

MENU

Menu and up arrow button

LED

indicator

Power indicator

Mode indicator

TAKE

Confirm button

Com indicator

ALL

Distributor selection button

IR receiver

Receive the infrared signal

SAVE

Save button

LCD Panel

Show operation menu items

Address：S603-604 Weiye Building Torch Hi-Tech Industrial Development Zone Xiamen, Fujian Province, P.R.C

Tel: 00865925771197 Fax: 00865925771202

Email: s[email protected] http://www.rgblink.cn

5

Back Panel

Input Interface

1

DVI Input DVI-D port

Other Interface

3

RS 232 IN serial communication

interface

4

RS 232 OUT serial communication

interface

5

Switch

6

Power IEC-3 port

Output Interface

2

DVI Output DVI-D port

Address：S603-604 Weiye Building Torch Hi-Tech Industrial Development Zone Xiamen, Fujian Province, P.R.C

Tel: 00865925771197 Fax: 00865925771202

Email: s[email protected] http://www.rgblink.cn

6

Operating Instruction

Content

 How to Switch between Input and Output Channel

 How to Switch One Input to all Outputs

 How to Read Device Status

 How to Set LOGO Display when Power on

 How to Set the EDID

 How to Set the Language

 How to Realize Cascade Setting

 How to Set the Machine Address

 How to Realize Signal Auto Take

 How to Lock the Front Panel

 How to Realize Hot Backup

 How to Save the Preset Input and Output Channel

 How to Load the Saved Input and Output Channel

 How to Reset the Factory Settings

Address：S603-604 Weiye Building Torch Hi-Tech Industrial Development Zone Xiamen, Fujian Province, P.R.C

Tel: 00865925771197 Fax: 00865925771202

Email: s[email protected] http://www.rgblink.cn

7

How to Switch between Input and Output Channel

User can switch the signals between input and output channel by front panel buttons of

DXP D0808, specific operations are as follows:

1. If choose “AUTO TAKE ON”, push any button on output area on the front panel, for example,

choose [5] as the output channel.

Then push any button on Input area on the front panel, for example, choose [3] as the input

channel, the signal of output channel 5 will be switched to the signal of input 3.

2. If choose “AUTO TAKE OFF”, push any button on output area on the front panel, for

example, choose [5] as the output channel.

Then push any button on input area on the front panel, for example, choose [3] as the input

Channel. After setting, push the [TAKE] button to confirm.

Note: Input channel: The signal that will be switched to output channel.

Output channel: The signal that connected to display device.

The number [1]~[8] means channel 1~8.

How to Switch One Input to all Outputs

1. If choose “AUTO TAKE ON”, push the [ALL] button on the front panel.

Then push any button on input area on the front panel, for example, choose [3] as the input

channel, all the signal of output channel will be switched to the signal of input 3.

2. If choose “AUTO TAKE OFF”, push the [ALL] button on the front panel.

Then push any button on Input area in the front panel, for example, choose [3] as the input channel.

Push the [TAKE] button to confirm, all the signal of output channel will be switched to the signal

of input 3.

Address：S603-604 Weiye Building Torch Hi-Tech Industrial Development Zone Xiamen, Fujian Province, P.R.C

Tel: 00865925771197 Fax: 00865925771202

Email: s[email protected] http://www.rgblink.cn

8

How to Read Device Status

1. Push the [MENU] button on the front panel, and enter to the menu items.

2. System default [STATUS] option, if it is not selected, push the [MENU] up arrow button or

[NEXT] down arrow button, and choose [STATUS].

3. Push the [TAKE] button to confirm, user can view the current device status. The first four

screen show each output to the corresponding input channel. The fifth screen shows the

software version, the sixth screen shows the serial number and the seventh screen shows

the machine address.

How to Set LOGO Display when Power on

1. Push the [MENU] button on the front panel, and enter to the menu items.

2. Push the [MENU] up arrow button or [NEXT] down arrow button, and choose [LOGO].

3. Push the [TAKE] button to confirm, and enter to LOGO setting, push the [NEXT] button

to choose “ON” or “OFF”, then push the [TAKE] button to confirm.

How to Set the EDID

1. Push the [MENU] button on the front panel, and enter to the menu items.

2. Push the [MENU] up arrow button or [NEXT] down arrow button, and choose [EDID].

3. Push the [TAKE] button to confirm.

4. Push any button on output area on the front panel, for example, choose [3] as the output channel.

5. Push any button on input area on the front panel, for example, choose [5] as the input channel.

6. Push the [TAKE] to confirm, and the EDID copy finish.

Note: When set the EDID, the output interface must be connected to monitors.

Address：S603-604 Weiye Building Torch Hi-Tech Industrial Development Zone Xiamen, Fujian Province, P.R.C

Tel: 00865925771197 Fax: 00865925771202

Email: s[email protected] http://www.rgblink.cn

9

How to Set the Language

1. Push the [MENU] button on the front panel, and enter to the menu items.

2. Push the [MENU] up arrow button or [NEXT] down arrow button, and choose [LANGUAGE].

3. Push the [TAKE] button to confirm, and enter to the language setting.

4. Push the [NEXT] button to choose the language, for example, choose “ENGLISH”, then

push the [TAKE] button to confirm.

How to Realize Cascade Setting

1. Push the [MENU] button on the front panel, and enter to the menu items.

2. Push the [MENU] up arrow button or [NEXT] down arrow button, and choose [CASCADE].

3. Push the [TAKE] button to confirm, and enter to the cascade setting. Push the [NEXT]

button to choose “ON” or “OFF”, then push the [TAKE] button to confirm.

How to Set the Machine Address

1. Push the [MENU] button on the front panel, and enter to the menu items.

2. Push the [MENU] up arrow button or [NEXT] down arrow button, and choose [MAC ADDR].

3. Push the [TAKE] button to confirm. Push any one of button [1]~[8] on output area to set the

machine address. Push the [TAKE] button to confirm after setting.

Address：S603-604 Weiye Building Torch Hi-Tech Industrial Development Zone Xiamen, Fujian Province, P.R.C

Tel: 00865925771197 Fax: 00865925771202

Email: s[email protected] http://www.rgblink.cn

10

How to Realize Signal Auto Take

1. Push the [MENU] button on the front panel, and enter to the menu items.

2. Push the [MENU] up arrow button or [NEXT] down arrow button, and choose [AUTO TAKE].

3. Push the [TAKE] button to confirm, and enter to the auto take setting. Push the [NEXT]

button to choose “ON” or “OFF”, then push the [TAKE] button to confirm. System default the

status is “ON”, and when switch the signal, user need not to push the [TAKE] button.

How to Lock the Front Panel

1. Push the [MENU] button on the front panel, and enter to the menu items.

2. Push the [MENU] up arrow button or [NEXT] down arrow button, and choose [LOCK].

3. Push the [TAKE] button to confirm. Push the [NEXT] button to choose “ON” or “OFF”, then

push the [TAKE] button to confirm. Push the [MENU] button for 3 seconds to unlock panel.

How to Realize Hot Backup

1. Push the [MENU] button on the front panel, and enter to the menu items.

2. Push the [MENU] up arrow button or [NEXT] down arrow button, and choose [HOT BACKUP].

3. Push the [TAKE] button to confirm, and enter to hot backup function setting. Push the [NEXT]

button to choose “ON” or “OFF”, then push the [TAKE] button to confirm.

Inputs 1 ~ 8 are any combination of backup, it will recall another backup if one signal has

problem. The detailed parameters can be set on windows control program, and invalid for

button operation.

Address：S603-604 Weiye Building Torch Hi-Tech Industrial Development Zone Xiamen, Fujian Province, P.R.C

Tel: 00865925771197 Fax: 00865925771202

Email: s[email protected] http://www.rgblink.cn

11

How to Save the Preset Input and Output Channel

1. Push the [SAVE] button on the front panel, the button light is on. At the same time, some

buttons [1]~[8] in output and input area are on and some flash. Button is on can be saved,

and button flashes will be overwrite.

2. Choose the button on to save, the LED screen will show save complete.

3. If choose the button flash, the information saved before will be overwrite.

4. Push the [TAKE] button to confirm, and push [MENU] button to cancel.

5. Push the [MENU] to exit the save state, or push the [SAVE] button, the light is off, and exit

the save state.

Note: The buttons [1]~[8] on output area corresponding to save 1~8, and the buttons [1]~[8]

on output area corresponding to save 9~16.

How to Load the Saved Input and Output Channel

1. Push the [LOAD] button on the front panel, the button light is on. At the same time, some

buttons [1]~[8] in output and input area are on and some flash. Button on is ready for recall,

and button flashes means just recall. Push the button on to recall.

2. Push the [MENU] button to exit the load state, or push the [LOAD] button, the button light is

off, and exit the load state.

How to Reset the Factory Settings

1. Push the [MENU] button on the front panel, and enter to the menu items.

2. Push the [MENU] up arrow button or [NEXT] down arrow button, and choose [RESET].

3. Push the [TAKE] button to confirm.

4. Push any key to reset factory settings, and push the [MENU] button to exit.

Address：S603-604 Weiye Building Torch Hi-Tech Industrial Development Zone Xiamen, Fujian Province, P.R.C

Tel: 00865925771197 Fax: 00865925771202

Email: s[email protected] http://www.rgblink.cn

12

Contact Information

Warranty:

All video products are designed and tested to the highest quality standard and backed by

full 3 years parts and labor warranty. Warranties are effective upon delivery date to

customer and are non-transferable. RGBlink warranties are only valid to the original

purchase/owner. Warranty related repairs include parts and labor, but do not include

faults resulting from user negligence, special modification, lighting strikes, abuse

(drop/crush), and/or other unusual damages.

The customer shall pay shipping charges when unit is returned for repair.

Headquarter: S603~604 Weiye Building Torch Hi-Tech Industrial Development Zone

Xiamen, Fujian Province, P.R.C

● Tel: +86-592-5771197

● Fax: +86-592-5771202

● Customer Hotline: 4008-592-315

● Web:

~ http://www.rgblink.com

~ http://www.rgblink.cn

● E-mail: s[email protected]

RGBlink DXP D0808 Quick start guide

RGBlink DXP D0808 Quick start guide

Related papers

Other documents