RGBlink DXP V0808 Quick start guide

Category
Video switches
Type
Quick start guide

RGBlink DXP V0808 is a matrix switching system designed for signal switching in various applications, including television broadcasting, multimedia meeting rooms, and video conferencing. It supports any input and output combination, independent output switching, and infrared remote control. Input and output can be modularized for added flexibility. With RS-232 loop out, multiple units can be controlled simultaneously. EDID management ensures compatibility with different display devices.

RGBlink DXP V0808 is a matrix switching system designed for signal switching in various applications, including television broadcasting, multimedia meeting rooms, and video conferencing. It supports any input and output combination, independent output switching, and infrared remote control. Input and output can be modularized for added flexibility. With RS-232 loop out, multiple units can be controlled simultaneously. EDID management ensures compatibility with different display devices.

DXP V0808 Quick Start
VIEWSIZE THE WORLD
Support any in any out
Support independent output switching
Support infrared remote control
Input and output can be modularized
RS 232 loop out for multiple control
Support EDID management
AddressS603-604 Weiye Building Torch Hi-Tech Industrial Development Zone Xiamen, Fujian Province, P.R.C
Tel: 00865925771197 Fax: 00865925771202
Email: [email protected] http://www.rgblink.cn
1
CONTENT
Product Introduction ............................................................................................................................... 2
Packing Configuration ............................................................................................................................ 3
Hardware Orientation .............................................................................................................................. 4
Front Panel ......................................................................................................................................... 4
Back Panel ......................................................................................................................................... 5
Operating Instruction .............................................................................................................................. 6
Content ............................................................................................................................................... 6
How to Switch between Input and Output Channel .................................................................... 7
How to Switch One Input to all Outputs ...................................................................................... 7
How to Close One Output Channel ............................................................................................ 7
How to Close all Output Channels .............................................................................................. 8
How to Set One-to-one Correspondence for Input and Output Channel ................................... 8
How to Save Pre-set Input and Output Channel ........................................................................ 8
How to Call Pre-set Input and Output Channel Saving Mode .................................................... 9
How to Factory Reset ................................................................................................................. 9
How to Read Equipment Related Information ............................................................................ 9
How to Set LOGO Display when Power on .............................................................................. 10
Contact Information............................................................................................................................... 11
AddressS603-604 Weiye Building Torch Hi-Tech Industrial Development Zone Xiamen, Fujian Province, P.R.C
Tel: 00865925771197 Fax: 00865925771202
Email: [email protected] http://www.rgblink.cn
2
Product Introduction
Matrix switching system is the whole cross
high performance device, used for signal
switching. Mainly used in television
broadcasting system signal switching and
exchange, multimedia meeting room, large
screen projection display engineering,
government conference room, hospital
medical discussion conference room,
television signal switching, interactive
multimedia classrooms, and military command
video conference room.
RGBlink strong technical strength determines
the high quality of AVDXP series matrix
switchers. We choose the chips with best
performance, elaborate design for every way
of switchers, to ensure the high quality of
switchers. After rigorous testing, VGA
switching signal bandwidth is 500 MHz (-3db),
support resolution of 1024x768@60Hz to
2048x1536@60Hz, fully meet various strict
System Connection
RGBlink offers solutions to
demanding technical problems.
Any application questions, or
required further information,
please contact with our
customer Support Engineers.
DXP V0808 System Connection Diagram
AddressS603-604 Weiye Building Torch Hi-Tech Industrial Development Zone Xiamen, Fujian Province, P.R.C
Tel: 00865925771197 Fax: 00865925771202
Email: [email protected] http://www.rgblink.cn
3
Packing Configuration
Note: Chinese Standard, American Standard or European Standard power cord is option.
The color of the screw driver is randomly when packing.
Power Cord
9-pin Serial
Cable
USB Disk
DVI HDMI 线
Antistatic Bag
防静电袋
Screw Driver
Certification
AddressS603-604 Weiye Building Torch Hi-Tech Industrial Development Zone Xiamen, Fujian Province, P.R.C
Tel: 00865925771197 Fax: 00865925771202
Email: [email protected] http://www.rgblink.cn
4
Hardware Orientation
Front Panel
Button Instruction
0~8
Selection button for input and output
channel, and number choice of save
or call saving modes. [0] button can
also be used to shut down the
channel output.
Rec
Load button
20+
UP arrow button and decimal button
Save
Save button
30+
Down arrow button
Esc
Exit button
ALL
Distributor selection button
LED
indicator
Power indicator
F1. F2
Fast call user save mode
Mode indicator
Menu
Menu button
Com indicator
Mode
Audio and video switching button
IR receiver
Receive the infrared signal
Enter
Confirm button
LCD Panel
Show operation menu items
AddressS603-604 Weiye Building Torch Hi-Tech Industrial Development Zone Xiamen, Fujian Province, P.R.C
Tel: 00865925771197 Fax: 00865925771202
Email: [email protected] http://www.rgblink.cn
5
Back Panel
Input Interface
1
VGA Input DB15 port
Other Interface
3
RS 232 IN serial communication
interface
4
RS 232 OUT serial communication
interface
5
Switch
6
Power IEC-3 port
Output Interface
2
VGA Output DB15 port
AddressS603-604 Weiye Building Torch Hi-Tech Industrial Development Zone Xiamen, Fujian Province, P.R.C
Tel: 00865925771197 Fax: 00865925771202
Email: [email protected] http://www.rgblink.cn
6
Operating Instruction
Content
How to Switch between Input and Output Channel
How to Switch One Input to all Outputs
How to Close One Output Channel
How to Close all Output Channels
How to Set One-to-one Correspondence for Input and Output Channel
How to Save Pre-set Input and Output Channel
How to Call Pre-set Input and Output Channel Saving Mode
How to Factory Reset
How to Read Equipment Related Information
How to Set LOGO Display when Power on
AddressS603-604 Weiye Building Torch Hi-Tech Industrial Development Zone Xiamen, Fujian Province, P.R.C
Tel: 00865925771197 Fax: 00865925771202
Email: [email protected] http://www.rgblink.cn
7
How to Switch between Input and Output Channel
DXP V0808 can rapidly switch any way signals by the front panel buttons, specific operations are as
follows:
1. Push the number button to select the input channel, for example, push the button [3].
2. Push the number button again to select the output channel, for example, push the button [5].
3. After selection, push the button [Enter] to confirm.
Note: Input channel: The signal that will be switched to output channel.
Output channel: The signal that connected to display device.
The number [1]~[8] means channel 1~8.
How to Switch One Input to all Outputs
1. Push the number button, for example, push the button [2].
2. Then push the button [ALL], and input 2 will be switched to all outputs.
User can also operate by the following ways:
1. Push the button [ALL].
2. Then choose the input channel, for example, push the button [2].
3. Push the button [Enter] to confirm.
How to Close One Output Channel
1. Push the button [0] on the front panel.
2. Choose output channel, for example, push the button [8].
3. Push the button [Enter] to confirm.
AddressS603-604 Weiye Building Torch Hi-Tech Industrial Development Zone Xiamen, Fujian Province, P.R.C
Tel: 00865925771197 Fax: 00865925771202
Email: [email protected] http://www.rgblink.cn
8
How to Close all Output Channels
1. Push the button [0] on the front panel.
2. Then push the button [ALL] on the front panel.
User can also operate by the following ways:
1. Push the button ALLon the front panel.
2. Push the button 0on the front panel.
3. Push the button [Enter] to confirm.
How to Set One-to-one Correspondence for Input and
Output Channel
1. Push the button [Rec] on the front panel.
2. Push the button [0] on the front panel.
3. Push the button [Enter] to confirm.
How to Save Pre-set Input and Output Channel
1. Push the button [Save] on the front panel.
2. User can choose 24 kinds of mode from button [1]~[24], for example, push the button [2].
3. Push the button [Enter] to confirm.
AddressS603-604 Weiye Building Torch Hi-Tech Industrial Development Zone Xiamen, Fujian Province, P.R.C
Tel: 00865925771197 Fax: 00865925771202
Email: [email protected] http://www.rgblink.cn
9
How to Call Pre-set Input and Output Channel Saving
Mode
1. Push the button [Rec] on the front panel.
2. User can choose 25 kinds of mode from button [0]~[24], for example, push the button [7].
3. Push the button [Enter] to confirm.
Note: [0] is default for one-to-one correspondence for input and output way. That is input [1] is
corresponding to output [1], input [2] is corresponding to output [2]
How to Factory Reset
1. Push the button [Menu] on the front panel.
2. Push the button [30+] DOWN arrow button, or button [20+] UP arrow button, make RESET option
for selected state.
3. Push the button [Enter] to confirm and enter the initialization interface.
4. Push any button according to the LCD hint and complete factory reset.
How to Read Equipment Related Information
1. Push the button [Menu] on the front panel.
2. System default STATUS option, if it is not selected, push the [30+] DOWN arrow button or [20+] UP
arrow button and choose <STATUS>.
3. Push the button [Enter] to confirm, read the information by the [30+] DOWN arrow button or [20+]
UP arrow button.
AddressS603-604 Weiye Building Torch Hi-Tech Industrial Development Zone Xiamen, Fujian Province, P.R.C
Tel: 00865925771197 Fax: 00865925771202
Email: [email protected] http://www.rgblink.cn
10
How to Set LOGO Display when Power on
1. Push the button [MENU] on the front panel.
2. Push the [30+] DOWN arrow button or [20+] UP arrow button and select <LOGO>.
3. Push the button [Enter] to confirm, and enter LOGO switch setting, LOGO ON or OFF at boot can
be set.
AddressS603-604 Weiye Building Torch Hi-Tech Industrial Development Zone Xiamen, Fujian Province, P.R.C
Tel: 00865925771197 Fax: 00865925771202
Email: [email protected] http://www.rgblink.cn
11
Contact Information
Warranty:
All video products are designed and tested to the highest quality standard and backed by
full 3 years parts and labor warranty. Warranties are effective upon delivery date to
customer and are non-transferable. RGBlink warranties are only valid to the original
purchase/owner. Warranty related repairs include parts and labor, but do not include
faults resulting from user negligence, special modification, lighting strikes, abuse
(drop/crush), and/or other unusual damages.
The customer shall pay shipping charges when unit is returned for repair.
Headquarter: S603~604 Weiye Building Torch Hi-Tech Industrial Development Zone
Xiamen, Fujian Province, P.R.C
Tel: +86-592-5771197
Fax: +86-592-5771202
Customer Hotline: 4008-592-315
Web:
~ http://www.rgblink.com
~ http://www.rgblink.cn
E-mail: support@rgblink.com
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12

RGBlink DXP V0808 Quick start guide

Category
Video switches
Type
Quick start guide

RGBlink DXP V0808 is a matrix switching system designed for signal switching in various applications, including television broadcasting, multimedia meeting rooms, and video conferencing. It supports any input and output combination, independent output switching, and infrared remote control. Input and output can be modularized for added flexibility. With RS-232 loop out, multiple units can be controlled simultaneously. EDID management ensures compatibility with different display devices.

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI