Sricam MiNi IP Camera Owner's manual

Brand: Sricam

Model: MiNi IP Camera

Type: Owner's manual

Sricam

Sricam Sricam

MiNi IP Camera

Quick User Manual

IR Sensor

Lens

Speaker

Microphone

Reset

MicroSD card Slot

SP009

DC 5V Power Slot

Your camera is offline.Please check camera

network connection

Step 1, Power on the IPCam

Step 2, Press Reset button by the reset pin

for 10 seconds untill hearing a clash sound

from the IPCam

Step 3, Wait untill you hearing continuous Di-

Di-Di...sound from the camera,Touch Next

Add device

salestest

Input Wi-Fi Password

Wi-Fi Setting..., Please wait...

Wi-Fi setting

Note:

Go directly to Next if you already

finished this tips at “Step3 Product connection”

Input Wi-Fi Password

Wi-Fi Setting

Wi-Fi setting succeeded

Skip

Modify Password

Note: Touch this button for setting

APP“Authority, Multi-Media, System,

Update, Logout, Quit. ”

Note: Please creat

6-10 characters(0-9) for

your new password

office Add new device

Smart Wi-Fi Setting

Add device

Note: You can find the device

ID from the label which sticked on

the camera.

Creat the device name here,

such as: Office, Home...

Note: Mini IP Camera

without Lan Port(RJ-45), So

after power on the camera, touch

“Smart Wi-Fi Setting” for

add new device

Add new device

Reset

Sricam

Sricam App Installation

Start setup

Step1.

Step2. Register an App user account

[email protected]

2-1

FAQ1-2

FAQ1-4 FAQ1-5

FAQ1-1

FAQ1-3

2-2 2-3

registered

email in 2-2

Please create a

password for APP account,

pls don't input your email

password.

Sricam

Step3. Product connection

Step4. Add the camera on App

4-1 4-2 4-3

4-4 4-5 4-6

4-7 4-8 4-9

Please visit :

www.sricctv.com/en/onlinesupport

Note:Touch

for play, keepping touch

for setting

Note:Touch

for stream, keepping

touch for Setting

587

1. Sender: Please input your email address (e.g., [email protected]).

2. SMTP address: The server address for the Sender's email account.

Port: Please select 587 or 465 if the SMTP address is mtp.gmail.com, Smtp.mail.yahoo.com or smtp.live.com

Hotmail.com

If not, please select 25.

4. Password: The Password for the email account.

5. Email: Enter up to three receiving email accounts (e.g., you may have both [email protected] and Marcy@

yahoo. com) as picture FAQ3-4.

FAQ2: MicroSD card record and playback setting

1) Insert the microSD card to the camera

2) MicroSD card format and record setting

(Note: The App can't format 64GB and 128GB MicroSD card directly, so you need format 64, 128GB MicroSD

card via SD card reader on PC.)

Touch " Playback" for playback the record on MicroSD card.as picture below (Note: each record is 30 minutes)

-8-

-6--5-

Method-1: WiFi setting via MicroSD card

1) Power off the camera.

2) Download WifiInfo.txt fromwww.download.sricam.com/Manual/WifiInfo.txt

3) Open the WifiInfo.txt file and input your router's Wi-Fi SSID and password. For example:the router's

Wi-Fi SSID is: sricam and Password is: sricam123. then input this information as picture :FAQ1-1.

4) Copy this WifiInfo.txt file to a empy MircoSD card.

5) Insert the MircoSD card to IP camera and power on the camera.

6) Wait for 1 min until hear a “clash”sound from the camera,the clash sound means Wi-Fi settings success.

7) Add the camera to App, Back to user manual Step4 Add the camera on the App.

Method-2: WiFi setting via scan QR Code

1) After

Wi-Fi setting failed

, You will get the following tips:

2) Click “QR Code Setting”, and input Wi-Fi password, Click “Next”.

You will get a Wi-Fi QR Code on your smartphone, please direct put the lens of the camera to the QR code

within20-30cm and move forward slowly. when you hear a clash sound from the camera, click “Next” the

camera successfully connected to Wi-Fi.

Note:

Step5. Live video stream on your smartphone

For additional FAQs, Please visit:

Customer Service

Monday - Friday

9:00-18:00 Beijing Time (UTC +8)

Telephone: +86-755-29360806

E-mail: [email protected]

Skype ID: tech.sricam

Website:www.sricctv.com

After download the App “Sricam”, please Install and register a user account for it.

Products Introduction

Before starting setup

Make sure of the following:

- Your router supports the 2.4GHz frequency band (802.11b/g/n).

- Your router DHCP is enabled.

- Your smartphone is connected to the Internet with a WLAN/Wi-Fi that the camera will connect with.

- Your smartphone, camera, and router should be within approximately 8 feet during setup. After your

camera is set up, you can move the camera to your preferred location.

- You know the WLAN/Wi-Fi password.( No special characters in the password such as @#$%^&*)

Go directly to Step3 if the sricam app is already download and registered in your smartphone.

FAQ1: Wi-Fi setting failed

2) Second Enable the function you need, such as motion detection alarm, email alarm and

phone push alarm as picture FAQ3-3.

- Sricam owns the copyright -

Scan the QR code to download the“Sricam” App.

Search“Sricam”on Google Play or iOS App Store

FAQ3-1

FAQ3-3 FAQ3-4

FAQ3-2

ShenZhen Sricctv Technology Co., Ltd.

If you can’t hearing the “Di-Di-Di...”sound from the camera within 1 minute, you need reset the

camera first. Please press RESET button by the reset pin for a few seconds until you hear

a clash sound from the camera. Then waiting until you hearing continuous “Di-Di-Di...” sound

from the camera and go to Step4 for add the camera on App “sricam”.

Waiting

on App “sricam”.

Please direct put the lens of the

camera to the QR code at the distance

of about 20-30cm and move forward

slowly. After hearing the sound of “di...

Sricamsales

Please confirm whether the device sound

the beeping sound

If beeping,please check the Wi-Fi

password again

If this setting fails several times, please

try “QR Code Setting” way to configure

Try Again

QR Code Setting

Wi-Fi setting failed

QR Code Setting

Wi-Fi Setting...

QR Code Setting

FAQ2-1 FAQ2-2 FAQ2-3

4) Record playback on PC

A: First unplug the MicroSD card from the camera, and copy the record to your computer via a MicroSD card

reader.

B: Download the video Player software from link: http://download.sricam.com/rjxz.html

C: Install the Video Player and playback the record

FAQ2-4 FAQ2-5

-7-

Mini IP Camera PT Indoor IP Camera Outdoor IP Camera

FAQ3: Email and Phone Push Alarm setting

Your camera is offline. please check camera network

connection

step 1, Power the IPCam

Step 2, Connect the IPCam to your router or switch

with a net-cable, wait for switching to online mode ,

if not ,touch Smart Wi-Fi setting button

3) Record Playback(on App)

home home

Before Wifi setting, please make sure the camera still on WiFi setting Part..., you can still hear continuous

“Di-Di-Di...”sound from the camera. If can't, you need reset the camera first. ( For reset the camera check

user manual Step3 Product connection 3-3)

When scan the QR code, maybe you need try some different position and angle for scan succeed.

sricam

sricam123

First touch “Setting” menu and go to Alarm setting part as picture FAQ3-1 and FAQ3-2.

Note:

A: Enable the alarm by tapping the “Motion Detection Alarm” and “ Remote Defence”toggle switch to On .

A beepping sound from the camera signifies the alarm function successful activation.

B: The default Alarm Phone Push ID is your App account, if you don’t need, you can delete the push account.

3) Email Alarm setting

Touch " Email Alarm", and fill in the email information as below guide.

Microphone

press “Reset” button by the Reset-

pin for 10seconds your will hear a

clash sound, Untill you hearing

“Di-Di-Di...” sound from the device,..

Sricam MiNi IP Camera Owner's manual

Brand: Sricam

Model: MiNi IP Camera

Type: Owner's manual

Download PDF

report

Sricam MiNi IP Camera Owner's manual

Sricam MiNi IP Camera Owner's manual

Related papers

Other documents