Page is loading ...
PEX-D48
Language English
Version V1.0
Update Dec.2009
………………………………………………
W
1
hat’s in your package?
¾ One PEX-D48 series card
¾ One companion PCI CD (V4.6 or later)
¾ One Quick Start Guide(This document)
- 1 -
………………………………………………
In
stalling Windows Driver
Follow these steps:
1. Set up the Windows driver.
The driver is located at:
CD:\NAPDOS\PCI\PIO-DIO\dll_ocx\Driver
http://ftp.icpdas.com/pub/cd/iocard/pci/napdos/pci/pio-dio/dll_ocx/driver/
2
3. 2.
Quick Start
PE
X
-D48
1.
2. Click the button to start installation.
The Windows driver only supports Windows
2000/XP/2003/Vista 32-bit and Windows 7 32-bit versions.
3. Click the
button to install driver into the
default folder.
4. Click the
button to continue installation.
5. Select “NO, I will restart my computer later”
and then click the
button.
………………………………………………
In
3
stalling Hardware on PC
Follow these steps:
1. Shut down and power off your computer.
2. Remove the cover from the computer.
3. Select an unused PCI Express slot.
4. Plug the PEX-D48 into PCI Express slot.
5. Replace the PC cover.
6. Power on the computer.
After powering-on the computer, please finish the
Plug&Play steps according to the prompt message.
- 2 -
………………………………………………
P
4
in Assignments
- 3 -
CN1: 37 pin D-type female connector
(port-0, port-1, port2)
CN2: 50-pin flat-cable connector
(port-3, port-4, port-5)
PC_0
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
41
43
45
47
14
16
18
20
22
24
26
28
30
32
12
34
36
38
40
42
44
46
PB_7
GND
GND
GND
PC_1
PC_2
PB_4
PB_3
PB_5
PB_6
GND
GND
GND
GND
GND
GND
GND
PB_2
GND
PB_1
P
A
_
5
P
A
_
6
P
A
_
4
PA_0
PA_3
PB_0
PA _7
GND
GND
PA_2 GND
PA _1
GND
GND
GND
GND
49
48
50
GND
GND
V
CC
PC_5
1
3
5
7
9
4
6
8
10
2
PC_4
GND
GND
GND
PC_6
PC_7
PC_3GND
GND
PB_7
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
21
22
23
24
25
26
27
28
29
30
20
31
32
33
34
35
36
37
PB_6
PC_7
GND
V
C
C
N.C.
N.C.
PB_3
PB_2
PB_4
PB_5
PC_4
PC_3
PC_5
PC_6
PA_7
PC_1
PC_2
PB_1
PC_0
PB_0
N.C.
GND
GND
GND
N.C.
GND
N.C.
PA_0
PA_2
GND
PA_1
V
CC
PA_6
PA_5
PA_4
PA_3
Port No. PA0~7
A
ll signals are TTL compatible
TTL High(1)
2.4 V ~ 5.0 V
(Voltages over 5.0 V will damage the device)
None Defined 2.4 V ~ 0.8 V
TTL Low(0) Under 0.8 V
PB0~7 PC0~7
CN1 Port 0
Note:
Port 1 Port 2
CN2 Port 3 Port 4 Port5
………………………………………………
S
5
elf Test
1. Use the CA-3710
(Optional) and ADP-37 to
connect CN1 to CN2.
CN2
CN1
CA-5002
ADP-3
7
CA-3710
2. Execute the DIO sample program.
The sample program is contained in:
CD:\NAPDOS\PCI\PIO-DIO\dll_ocx\Demo
http://ftp.icpdas.com/pub/cd/iocard/pci/napdos/pci/pio-dio/dll_ocx/
demo/
- 4 -
3. Check the board number of the PEX-D48, and
test DIO functions.
Step1:
One PEX-D48 card
has been successfully
installed in PC.
Step2:
Select the board number
for the PEX-D48.
It starts from 0.
Step3:
Click this button
to do DIO
function test.
4. Check the DIO test result.
1 1 1 = 1 1 1 , Pass!!!
2 2 2 = 2 2 2 , Pass!!!
4 4 4 = 4 4 4 , Pass!!!
- 5 -
Complete
8 8 8 = 8 8 8 , Pass!!!
………………………………………………
A
- 6 -
dditional Information
9 PEX-D48 Series Card Product page:
http://www.icpdas.com/products/DAQ/pc_based/pio_d48.htm
6
9 CA-3710(Optional) and CA-5002(Optional) page:
http://www.icpdas.com/products/Accessories/cable/cable_selection.htm
9 ADP-37(Optional) page:
http://www.icpdas.com/products/DAQ/screw_terminal/adp_xx.htm
9 Documentation:
CD:\NAPDOS\PCI\PIO-DIO\manual
CD:\NAPDOS\PCI\Manual
http://ftp.icpdas.com/pub/cd/iocard/pci/napdos/pci/pio-dio/manual/
9 Software:
CD:\NAPDOS\PCI\PIO-DIO\
http://www.icpdas.com/download/pci/piodio/index.htm
The ICP DAS Web Site
http://www.icpdas.com
Contact Us
Technical support
Supplies and ordering information
Information related to upgrades, new
technologies, products and solutions
FAQ
Application examples
Copyright ©2009 by ICP DAS Co., Ltd. All rights are reserved
/
