- 1 -
Language
English
Version V1.0
Update Dec.2009
………………………………………………
What’s in your package?
One PCI-D64HU card
One companion PCI CD (V4.7 or later)
One Quick Start Guide (This document)
One CA-4037W cable and two CA-4002 D-Sub
connectors
1
P
CI
-
D64HU
Quick Start
3.
CA
-
403
7W
CA
-
4002
PCI
-
D64HU
1. 4. 2.
CD
- 2 -
………………………………………………
Installing Windows Driver
Follow these steps:
1. Set up the Windows driver.
The driver is located at:
CD:\NAPDOS\PCI\PCI-D64\DLL\Driver
http://ftp.icpdas.com/pub/cd/iocard/pci/napdos/pci/pci-d64/dll/driver
2. Click the button to start the installation.
3. Click the button to install the driver into
the default folder.
4. Click the button to continue the
installation.
5. Select “NO, I will restart my computer later”
and then click the button.
2
The Windows driver only supports Windows 2000/ XP versions.
- 3 -
………………………………………………
Installing Hardware on PC
Follow these steps:
1. Shut down and power off your computer.
2. Remove the cover from the computer.
3. Select an unused PCI slot.
4. Carefully insert your I/O card into the PCI slot.
5. Replace the PC cover.
6. Power on the computer.
After powering-on the computer, please finish the
Plug&Play steps according to the prompt message.
3
- 4 -
………………………………………………
Pin Assignments
4
D I1 8
1
3
5
7
9
11
1 3
1 5
1 7
1
9
2
1
2 3
2 5
2 7
2 9
3 1
3 3
3 5
3 7
4
6
8
1 0
1 2
1 4
1 6
1 8
2
0
2 2
2
2 4
2 6
2 8
3 0
3
2
3
4
3
6
D I1 9
D O 1 8
D O 1
7
D O 1 6
D I1 7
D I1 6
D I2 2
D I2 3
D I2 1
D I2 0
D O 2 1
D O 2 2
D O 2 0
D O 1 9
D O 2 6
D O 2 4
D O 2 3
D I2 4
D O 2 5
D I2 5
D I
2 9
D I
2 8
D
I
3 0
O _ R E Q
D I 3 1
C
O
N
2
D I2 6
D I2 7
O
_ T R G
D O 3 1
+ 5 V
G N D
O _ A C K
D O 2 7
D O 2 8
D O 2 9
D O 3 0
3 9
3
8
4
0
N .C
.
N .C .
N . C .
DI2
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
21
22
23
24
25
26
27
28
29
30
20
31
32
33
34
35
36
37
DI3
DO2
DO1
DO0
DI1
DI0
DI6
DI7
DI5
DI4
DO5
DO6
DO4
DO3
DO10
DO8
DO7
DI8
DO9
DI9
DI13
DI12
DI14
I_REQ
DI15
C
O
N
1
DI10
DI11
I_TRG
DO15
+5V
GND
I_ACK
D
O11
DO12
DO13
DO14
- 5 -
………………………………………………
Self Test
1. Use the CA-3710 to connect the CON1 on
board to DN-37 wiring terminal board (Optional).
2. Connect the DI (0~15) with DO (0~15).
DI0 with DO0 ... DI15 with DO15
5
C
O
N1
C
O
N
2
1
2
3 4 5 6 7 8 9
10
11
1
2
1
3
14
15
16
17
18 19
20
21 22 23 24 25 2
6 27 28
29
30 31 32 33 34 35 36
37
DN-37 I/O Wiring
CA
-
3710
- 6 -
3. Execute the DIO sample program.
The sample program is contained in zip file which is
located at:
CD:\NAPDOS\PCI\PCI-D64\DLL\Demo
4. Test DIO (0~15) function and get to test result.
※ The DI (16~31) do not connect to DO (16~31), wherefore
channel 16~31 show high status (Red light).
1
2
3
C
lick the
DO
for channel
0 、4、8、12、
15
.
Check the
DI
of
channel 0、4、8、
12、15 are high
state. (Red light)
Click this
button to
output do.
Complete
- 7 -
………………………………………………
Additional Information
PCI-D64HU Card product page:
http://www.icpdas.com/products/DAQ/pc_based/pci-d64hu.htm
CN-37 wiring terminal board (Optional) page:
http://www.icpdas.com/products/DAQ/screw_terminal/dn_37.htm
CA-3710(Optional) cable page:
http://www.icpdas.com/products/Accessories/cable/cable_selection.htm
Documentation:
CD:\NAPDOS\PCI\PCI-D64\manual
CD:\NAPDOS\PCI\manual
http://ftp.icpdas.com/pub/cd/iocard/pci/napdos/pci/pci-d64/manual/
Software:
CD:\NAPDOS\PCI\PCI-D64\
http://ftp.icpdas.com/pub/cd/iocard/pci/napdos/pci/pci-d64/dll/
The ICP DAS Web Site
http://www.icpdas.com
Contact Us
Copyright ©2009 by ICP DAS Co., Ltd. All rights are reserved
6
Technical support
Supplies and ordering information
Information related to upgrades, new
technologies, products and solutions
FAQ
Application examples
/