American Standard 4462F.002 Installation guide

American Standard
Brand
American Standard
Model
4462F.002
Category
Sanitary ware
Type
Installation guide

This manual is also suitable for

KITCHEN FAUCETS
4462F
4464F
M968681
Certified to comply with ASME A112.18.1M
Plumbers' Putty or Caulking
Adjustable Wrench
Channel Locks
RECOMMENDED TOOLS
1
2
INSTALL FAUCET
INSTALL VALVE BODIES
Insert HOSE (3) and SPOUT (4) through hole in top of sink or
mountng surface.
Place SEAL RING (1) into SPOUT ESCUTCHEON (2).
From under sink install and LOCKNUT (5) onto SPOUT
SHANK (6). Center SPOUT (4) and tighten LOCKNUT (5) to
secure SPOUT (4).
Install LOCK NUT (1) onto VALVE BODIES (2). Insert VALVE BODY (2)
through hole from underside of sink or mountng surface.
From under sink or mountng surface, tighten LOCK NUT (1) to secure
VALVE BODY (2).
Place RUBBER RING (3) into ESCUTCHEON (4). Thread ESCUTCHEON
(4) onto VALVE BODY (2) until snug against internal stop.
4
5
6
1
3
2
Phillips Screwdriver
Flat Blade Screwdriver
Installation
Instructions
CAUTION
Turn off hot and cold water
supplies before beginning.
Thank you for selecting American-Standard...
the benchmark of fine quality for over 100 years.
To ensure that your installation proceeds smoothly--
please read these instructions carefully before you begin.
WYNSTON
1
3
4
2
M968681
3
WATER SUPPLY, TEE, SPOUT AND WASTE CONNECTIONS
NOTE: FLEXIBLE SUPPLIES OR BULL-NOSE RISERS NOT INCLUDED
AND MUST BE PURCHASED SEPARATELY.
HOT
HOT
COLD
1-1/2" O.D. TAILPIECE
FLEXIBLE
SUPPLIES
1/2" PIPE
THREAD
3/8 COMPRESSION
CONNECTION
2
1a
FERRULE
COMPRESSION
NUT
COUPLING
NUT
3/8 O.D.
BULL-NOSE
RISERS
3
9a
9
5
WASTE
OUTLET
Connect water supply to VALVE BODIES (1,1a) with1/2" IPS FLEXIBLE
SUPPLIES (2) or 3/8" O.D. BULL-NOSE RISERS (3). Use adjustable wrench
to tighten connections. Do not over tighten. Be careful not to kink copper
supply when bending. Use tubing cutter to cut to proper length.
Connect HOT water supply to left STOP and COLD water
supply to right STOP using sealant, appropriate connectors, and
COUPLING NUTS.
Connect male thread of PULL-OUT HOSE (4) to
COUPLING NUT (5) on TEE (6). Tighten with wrenches.
Thread COUUPLING NUTS (9, 9a) on TEE HOSES
to valve body inlets. Tighten with adjustable wrench.
Snap small end of HOSE HOLDER (7) between
TEE (6) and COUPLING NUT (5). Then snap
HOSE HOLDER (7) to SHANK (8).
Connect 1-1/2" O.D. tailpiece to DRAIN
waste outlet.
INSTALL WEIGHTS
Attach WEIGHTS (10) at bottom of loop on
Hose (4) as shown.
COLD
4
7
10
4
8
“P” TRAP
1
6
4
INSTALL HANDLES AND SOAP DISPENSER
Install SOAP DISPENSER (5) into separate hole
of sink or mounting surface. From underside of
mounting surface install RUBBER SPACER (6)
and MOUNTING NUT (7) onto DISPENSER
SHANK (8).
Hand tighten NUT (7).
Thread PLASTIC BOTTLE (9) into DISPENSER SHANK (8).
To fill PLASTIC BOTTLE (9), pull out the SOAP DISPENSER (5)
and fill from the top.
1
10
2
4a
5
3
4a
3a
1
6
TOP
SPLINE END DOWN
Fig. A.
Push ADAPTERS (1) on VALVE STEMS (2),
so that the hole of the ADAPTER (1) without
a spline is facing up. Fig. A. Tighten
STEM SCREW (10) to secure ADAPTER (1).
Thread HANDLE BASE (3,3a) clock-wise
until tight against ESCUTCHEON (4, 4a).
i
n
s
t
a
l
l
i
n
s
t
a
l
l
8
7
9
5
M968681
TEST INSTALLED FAUCET
5a
With HANDLES (1) in OFF position, turn on WATER SUPPLIES (2)
and check all connections for leaks.
With HANDLES (1) in "off" position, unthread SPRAY (3) from
HOSE END (4).
Operate both HANDLES (1) to flush water lines thoroughly.
Replace SPRAY (3) into HOSE END (4).
WASTE
OUTLET
COLD
HOT
2
2
1
3
4
1
SPRAY OPERATION
With FAUCET on press TOGGLE BUTTON (5) on
SPRAY (3) to switch from stream to spray.
Press and hold PAUSE BUTTON (6) to temporarily
stop flow from SPRAY (3). Release PAUSE BUTTON (6)
to resume flow from SPRAY (3).
REMOVE
STREAM (AERATOR)
SPRAY
7
6
DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.
DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A
CLOTH WITH A COARSE SURFACE.
CARE INSTRUCTIONS:
SERVICE
2
90˚
If spout drips, operate handles several times from
OFF to ON position. Do not force - handles turn only 90˚.
3
2
4
Turn valve to OFF position
Thread HANDLE BASE (1a) counter clock-wise until loose.
Pull HANDLE (1) “UP” firmly to release from
ADAPTER (2).
Remove SPRING CLIP (3). Lift STOP WASHER (4),
turn 90˚ and replace. Replace SPRING CLIP (3).
Re-install HANDLE ASSEMBLY (1).
To change direction of handle:
1
1a
i
n
s
t
a
l
l
r
e
m
o
v
e
6
3
5
  • Page 1 1
  • Page 2 2
  • Page 3 3

American Standard 4462F.002 Installation guide

American Standard
Brand
American Standard
Model
4462F.002
Category
Sanitary ware
Type
Installation guide
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents