WaterWorks DSKM20 Installation guide

WaterWorks
Brand
WaterWorks
Model
DSKM20
Category
Faucets
Type
Installation guide
STYLE No. DSKM20
Dash Three Hole Gooseneck
Kitchen Faucet with Metal Cross
Handles and Spray
INSTALLATION
GUIDELINES
PAGE 1 OF 5 | UPDATED ON 2.21.2023
PRODUCT SUPPORT | 800.927.2120 | WATERWORKS.COM
IMPORTANT:
To ensure this product is installed properly, you must
read and follow these guidelines.
The owner/user of this product must keep this
information for future reference.
This product must be installed by a professional
licensed contractor.
Be sure your installation conforms to federal state,
and local codes. In the State of Massachusetts, all
installations must comply with the rules and
regulations set forth within 248 CMR.
Inspect this product to ensure you have all the parts
required for proper installation. Product is sold
partially assembled but shown fully disassembled for
illustrative and service purposes only.
Use only a strap wrench or protected/smooth-jaw
wrench on any finished surface.
The use of certain plumber’s putty may stain stone
or tile surfaces.
If further assistance is required, please contact
Product Support at 1-800-927-2120 Monday through
Friday, 8am – 6pm EST.
Refer to the separate Service Parts Documents for
available replacement parts.
TECHNICAL DETAILS:
DETAIL SPECIFICATION
DECK THICKNESS 3/8” [10mm] MIN - 2” [51mm] MAX
HANDLE TURN ANGLE QUARTER TURN
INLET CONNECTION TYPE 1/2” MALE WITH SUPPLY NUT
SPOUT REACH 10-3/8” [264mm]
SPOUT SWIVEL YES
SPRAY HOSE LENGTH 59” [1.5m]
SPRAY INCLUDED IN UNIT YES
WATER PRESSURE RANGE 20psi [1.5 bar] MIN - 85psi [6.0 bar] MAX
WATER PRESSURE RECOMMENDED 45psi [3.0 bar]
8"MIN - 12"MAX
[203mm] [305mm]
HANDLE SPREAD
Ø1-3/8"
[35mm]
FITTINGS
HOLE
"HANDLE"
Ø1-5/8"
[41mm]
FITTINGS HOLE
"SPRAYER"
[LEFT OR
RIGHT SIDE]
Ø1-3/8"
[35mm]
FITTINGS HOLE
"SPOUT"
Ø1-3/8"
[35mm]
FITTINGS HOLE
"HANDLE"
STYLE No. DSKM20
Dash Three Hole Gooseneck
Kitchen Faucet with Metal Cross
Handles and Spray
INSTALLATION
GUIDELINES
PRODUCT SUPPORT | 800.927.2120 | WATERWORKS.COM
RUBBER WASHER
[DO NOT REMOVE]
METAL WASHER
SPOUT
SHANK
PLASTIC SPACER
RUBBER
WASHER
NUT
RUBBER
WASHER
TEE
RUBBER WASHER
[DO NOT REMOVE]
METAL WASHER
SPOUT ESCUTCHEONESCUTCHEON
SHANK
PLASTIC SPACER
RUBBER
WASHER
NUT
RUBBER
WASHER
TEE
NUT
METAL WASHER
RUBBER WASHER
PLASTIC SPACER
MOUNTING
SURFACE
SHANK
RUBBER WASHER*
ESCUTCHEON
SPOUT
* If desired, a bead of
caulk or a clear
silicon may be
applied where the
ESCUTCHEON
contacts the
mounting surface.
SHANK
RUBBER
WASHER
TEE
SHANK
RUBBER
WASHER
TEE
RUBBER
WASHER
CHECK
VALVE
FLOW
REGULATING
CHECK
VALVE
ADAPTER
1. Unthread and remove the TEE, NUT, lower deck
WASHERS and PLASTIC SPACER from SHANK.
NOTE: Do NOT remove the RUBBER WASHER
beneath the ESCUTCHEON.
2. Insert the SPOUT through the hole on the mounting
surface making sure the RUBBER WASHER
provided is beneath the ESCUTCHEON then re-
install the PLASTIC SPACER, WASHERS and
securely tighten the NUT.
3. Using the RUBBER WASHER provided, thread and
securely tighten the TEE back onto the SHANK.
NOTE: 2 CHECK VALVES, 1 flow regulating, are
located inside the ADAPTER at the base of the TEE.
SIDE BODY
GLAND COVER
HANDLE
FINISHED SCREW
[CAUTION]
SIDE BODY
GLAND COVER
HANDLE
FINISHED SCREW
[CAUTION]
4. Carefully unthread the FINISHED SCREW then pull
the HANDLE and the GLAND COVER up.
PLASTIC
BUSHING
[DO NOT
REMOVE]
PLASTIC SPACER,
RUBBER WASHER,
METAL WASHER,
NUT
SIDE BODY
TRIM CONNECTOR
O-RING
ESCUTCHEON
TRIM NUT
[16mm WRENCH]
PLASTIC
BUSHING
[DO NOT
REMOVE]
PLASTIC SPACER,
RUBBER WASHER,
METAL WASHER,
NUT
SIDE BODY
TRIM CONNECTOR
O-RING
ESCUTCHEON
TRIM NUT
[16mm WRENCH]
5. Unthread and remove the TRIM NUT, remove the
ESCUTCHEON with the O-RING, unthread and
remove the TRIM CONNECTOR then fully thread
the NUT down the SIDEBODY.
CAUTION: Do NOT remove the PLASTIC BUSHING
on the TRIM NUT.
SIDEBODY
PLASTIC SPACER,
RUBBER WASHER,
METAL WASHER,
NUT
TRIM CONNECTOR
SIDEBODY
PLASTIC SPACER,
RUBBER WASHER,
METAL WASHER,
NUT
TRIM CONNECTOR
6. Thread the TRIM CONNECTOR onto the SIDEBODY
until it stops and let it rest on the mounting surface
then hand-tighten the NUT against the underside
of the mounting surface.
CAUTION: Do NOT over-tighten the NUT to allow
for proper handle alignment during HANDLE
installation. PAGE 2 OF 5 | UPDATED ON 2.21.2023
STYLE No. DSKM20
Dash Three Hole Gooseneck
Kitchen Faucet with Metal Cross
Handles and Spray
INSTALLATION
GUIDELINES
PAGE 3 OF 5 | UPDATED ON 2.21.2023
PRODUCT SUPPORT | 800.927.2120 | WATERWORKS.COM
MOUNTING
SURFACE
SIDEBODY
TRIM
CONNECTOR
O-RING*
ESCUTCHEON
TRIM NUT
[16mm WRENCH]
* If desired,a bead of
caulk or a clear silicon
may be applied where
the ESCUTCHEON
contacts the mounting
surface.
TRIM NUT
GLAND COVER
HANDLE
FINISHED SCREW
SIDEBODY
NUT
7. Place the ESCUTCHEON and O-RING over the TRIM
CONNECTOR then thread and securely tighten the
TRIM NUT into the TRIM CONNECTOR.
8. Re-attach the GLAND COVER, HANDLE and
FINISHED SCREW. Ensure the HANDLE is in the
desired orientation then securely tighten the NUT
on the SIDEBODY.
9. Repeat Steps 4 through 8 to install the second
HANDLE.
SUPPLY
HOSE
TEE
SUPPLY
HOSE
[2ND]
SUPPLY
HOSE
TEE
SUPPLY
HOSE
[2ND]
RUBBER WASHER
WITH SCREEN (x2)
10. Connect the SIDEBODIES to the TEE using the
SUPPLY HOSES provided. Securely tighten the
HOSES and ensure they are not pinched/kinked.
NOTE: Make sure to include the RUBBER
WASHERS WITH SCREENS provided on both sides
of the TEE.
RUBBER
WASHER
[DO NOT
REMOVE]
RUBBER
WASHER
METAL
WASHER
NUT
RUBBER
WASHER
[DO NOT
REMOVE]
RUBBER
WASHER
METAL
WASHER
NUT
11. Unthread and remove the NUT, METAL WASHER,
and RUBBER WASHER from the SHANK.
NOTE: Do NOT remove the RUBBER WASHER
beneath the ESCUTCHEON.
NUT
METAL
WASHER
RUBBER
WASHER
MOUNTING
SURFACE
SHANK
RUBBER WASHER*
NUT
METAL
WASHER
RUBBER
WASHER
MOUNTING
SURFACE
SHANK
RUBBER WASHER*
* If desired, a bead
of caulk or a clear
silicone may be
applied where the
ESCUTCHEON
contacts the
mounting surface.
12. Insert the SHANK through the hole on the
mounting surface making sure the RUBBER
WASHER provided is beneath the ESCUTCHEON
then re-install the WASHERS and securely tighten
the NUT.
SIDEBODY
[2ND]
HANDLE
[2ND]
SCREW
SIDEBODY
[2ND]
HANDLE
[2ND]
SCREW
STYLE No. DSKM20
Dash Three Hole Gooseneck
Kitchen Faucet with Metal Cross
Handles and Spray
INSTALLATION
GUIDELINES
PAGE 4 OF 5 | UPDATED ON 2.21.2023
PRODUCT SUPPORT | 800.927.2120 | WATERWORKS.COM
SPRAY HOSE
[CONICAL END]
SHANK
SPRAYER
SPRAY HOSE
[CONICAL END]
SHANK
SPRAYER
13. Insert the SPRAY HOSE [conical end] through the
SHANK and the ESCUTHCHEON then thread and
securely tighten the SPARYER onto the HOSE.
ADAPTER
SPRAY HOSE
[KNURLED END]
14. Insert the SPRAYER into the ESCUTCHEON until it
stops then securely tighten the HOSE [knurled end]
onto the TEE.
SUPPLY TUBE
[NOT SUPPLIED]
SUPPLY NUT
[SUPPLIED]
SUPPLY VALVE
[NOT SUPPLIED]
15. Make final SUPPLY VALVE [sold separately]
connections.
AERATOR
AERATOR
KEY
SPOUT
* TURN ON WATER
CHECK FOR LEAKS
16. Unthread and remove the AERATOR then turn on
the water to flush out any debris in the supply lines
and inspect all connections for leaks.
CAUTION: Flush out the supply lines prior to
operating the SPRAYER.
SUPPLY
HOSE
SUPPLY
HOSE
[2ND]
SUPPLY
HOSE
TEETEE
SUPPLY
HOSE
[2ND]
RUBBER WASHER WITH
SCREEN (x2)
[REMOVE, CLEAN, AND
RE-INSTALL]
17. Turn off the water and unthread both the SUPPLY
HOSES from the TEE to remove and clean the
RUBBER WASHER WITH SCREENS then re-install
the WASHERS and HOSES.
* TURN ON WATER
TRIGGER
SPRAY
SPRAY
HOSE
SPOUT
[360°SWIVEL]
AERATOR
AERATOR
KEY
18. Re-install the AERATOR then turn on water and
operate the SPRAY and SPOUT to ensure they
operate and function properly.
NOTE: 2-3 Seconds of residual water is typical on
large gooseneck faucets.
STYLE No. DSKM20
Dash Three Hole Gooseneck
Kitchen Faucet with Metal Cross
Handles and Spray
INSTALLATION
GUIDELINES
PAGE 5 OF 5 | UPDATED ON 2.21.2023
PRODUCT SUPPORT | 800.927.2120 | WATERWORKS.COM
SET SCREW
SPOUT
POST
[EXTERNAL
O-RINGS]
SERVICING THE SPOUT:
1. Loosen but do NOT remove the SET SCREW at the
base of the SPOUT then remove the SPOUT to
expose to POST and external O-RINGS.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5

WaterWorks DSKM20 Installation guide

WaterWorks
Brand
WaterWorks
Model
DSKM20
Category
Faucets
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents