American Standard 4771 User manual

Category
Sanitary ware
Type
User manual

This manual is also suitable for

TOP MOUNT
KITCHEN FAUCETS
Installation
Instructions
Thank you for selecting American-Standard...
the benchmark of fine quality for over 100 years.
To ensure that your installation proceeds smoothly--
please read these instructions carefully before you begin.
4771
1
INSTALL FAUCET
Place FAUCET (1) in position on sink.
Note: Putty is not necessary unless mounting surface is uneven.
Assemble and hand tighten LOCKNUTS (2) from underside of SINK.
PUTTY
(IF REQUIRED)
SINK
Certified to comply with ANSI A112.18.1M
U.S. Patent No. 5,819,789
M968950 Rev. 1.1
1
2
2
INSTALLATION OF OPTIONAL METAL LEVER HANDLES
(Supplied with Faucet)
7
3
2
6
1
4
5
Thread PORCELIAN LEVER HANDLE (2) counter-clockwise
and remove INDEX BUTTON with MOUNTING ROD ASSEMBLY (1),
HANDLE COLLAR (4) and O-RING (5).
Insert MOUNTING ROD ASSEMBLY (1) into METAL HANDLE (3),
HANDLE COLLAR (4) and O-RING (5).
Thread HANDLE ASSEMBLY (6) into ball of HANDLE BASE (7).
Apply pressure to the MOUNTING ROD ASSEMBLY (1)
while turning the HANDLE COLLAR (4), in order to tighten
firmly.
TM
M968950 Rev. 1.1
TEST INSTALLED FAUCET
5
3
Remove AERATOR (1).
Operate both handles to flush water lines thoroughly.
Turn handles into OFF position and replace AERATOR (1).
SERVICE
6
To change direction of handle rotation,
proceed as follows:
AERATOR may accumulate dirt causing distorted and reduced
water flow. Remove AERATOR and rinse clean.
If spout drips, operate handles several times from OFF to ON
position. Do not force - handles turn only 90˚.
SPRING
CLIP
STOP
WASHER
90˚
Turn valve to OFF position.
Pull out INDEX CAP and remove
HANDLE SCREW.
Pull off HANDLE BASE and remove
ADAPTER.
Remove SPRING CLIP.
Lift STOP WASHER, turn 90˚ and replace.
Replace SPRING CLIP.
Reinstall HANDLE.
WATER SUPPLY CONNECTIONS
AND INSTALL SPRAY HOLDER
Place SPRAY HOLDER (1) into separate hole of sink and
assemble NUT (2) onto shank.
From underside of sink hand tighten NUT (2).
1
2
3
With HANDLES in OFF position, turn on
WATER SUPPLIES (5) and check all
connections for leaks.
Turn faucet on and activate SPRAY (4) into sink.
Check spray connections for leaks.
CHECK FOR LEAKS
4
INSTALL SPRAY
From underneath sink, attach COUPLING NUT (5)
of SPRAY HOSE (2) to HOSE SHANK (6). Tighten
COUPLING NUT (5) firmly.
Feed SPRAY HOSE (2) through HOLDER (3) so
SPRAY (4) sits in HOLDER (3).
Unscrew SPRAY CAP (1).
4
3
1
1
6
2
5
4
FERRULE
COUPLING
NUT
1/2" IPS
FLEXIBLE SUPPLIES
3/8 O.D.
BULL-NOSE RISERS
Connect water supply to FAUCET with 1/2" IPS
FLEXIBLE SUPPLIES (3) or 3/8" O.D. BULL-NOSE
RISERS (4). Use adjustable wrench to tighten
connections.
Do not over tighten. Be careful not to kink
copper supply when bending. Use tubing
cutter to cut to proper length.
Do not use putty.
5
  • Page 1 1
  • Page 2 2

American Standard 4771 User manual

Category
Sanitary ware
Type
User manual
This manual is also suitable for

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI