Stag Hanger
ASSEMBLY INSTRUCTIONS
STAG HANGER Recommended Tools
RUSTICAHARDWARE.com
2
3
03
2017
VERSION
STAG HANGER Specications
Drill with 1/8”, 1/4”, and 3/8”
Drill Bits, 1-1/8” Forstner
Bit or 1-1/8” Spade Bit, and
Phillips Bit
9/16” and 5/8”
Combination Wrench
Socket Wrench with
9/16” and 5/8” Sockets
Level
Tape Measure Pencil
11-1/4”
1-7/8”
3-1/2”
3-1/4”
1”
2”
1-15/16”
2-7/8”
1/4”
3/16”
Use teamwork - We recommend
two people for this build.
STAG HANGER Parts
RUSTICAHARDWARE.com
3
3
03
2017
VERSION
A. B.
D.
C.
H.
E.
L.
F.
PARTS
A. Hanger Assembly
B. Lag Screw
C. Fastener Screw
D. Phillips Screw
E. 1” Washer
F. Anti-jump Bracket
G. Anti-jump Block*
H. Door Guide
I. Adjustable Spacers
J. Acorn Nut
K. Hard Stop & Rubber Bumper
L. Track
*For use on bi-parting door systems.
K.
J.
I.
G.
STAG HANGER Assembly Instructions
RUSTICAHARDWARE.com
4
3
03
2017
VERSION
2-3/8”
Installation
Holes
2”
Figure 1
Figure 2
NOTE:
Doors using Floor Mount Door Guides
will have a groove on the bottom. Ensure
this groove is on the opposite end of the
Door Hanger Installation.
1. Lay the door with the front facing up on a at,
level surface.
2. Place the hanger on the door (Figure 1).
3. Adjust the placement of the hanger for a 2-3/8”
gap between the top of the door and the bottom
edge of the wheel. Ensure the side of the hanger is
resting 2” from the edge of the door (Figure 2).
4. Mark the center of each installation hole with a
pencil. (Figure 2).
5. Repeat steps 2-4 for the opposite end of the
door. Set the hangers aside.
STAG HANGER Assembly Instructions
RUSTICAHARDWARE.com
5
3
03
2017
VERSION
Door Front
Door Front
Door Back
Figure 3
Figure 4
Figure 5
Figure 6
6. Drill two pilot holes all the way through the
door for each hanger using a drill with an 1/8” drill
bit (Figure 3).
7. Turn the door over. Using a 1-1/8” Forstner bit*,
drill a 7/16” deep hole into each pilot hole
(Figure 4).
*A 1-1/8” Spade bit may be used in pace of a Forstner bit.
8. Turn the door over, returning
it to the face-up position. Drill
all the way through the pilot
holes using a drill with a 3/8”
drill bit (Figure 5).
9. Install the hangers to the front of the door using
lag bolts, washers, and acorn nuts (provided)
(gure 6).
STAG HANGER Assembly Instructions
RUSTICAHARDWARE.com
6
3
03
2017
VERSION
1-5/8”
1/2”
Door Height
Figure 1
Figure 2
FIRST THINGS FIRST
Check to see if the oor below the track area is level. If the oor rises more than 1/2” the door may rub or
not slide open completely. If the oor is not level, measure from the highest point of the oor surface to
the recommended track placement and adjust track placement accordingly.
Ensure the track will be installed onto wall studs. If wall studs are not lining up with the installation a
header will be required to provide the necessary strength and stability for the track and door.
TRACK & DOOR INSTALLATION
2. Using a level and a pencil, make a line above
the doorway the same length as the track.
3. Hold the track up to where the pencil line is
visible through the holes in the track (Figure 2).
SUGGESTION:
Use pieces of double stick tape on the back of
the track to help hold the track in place while
completing steps 2 and 3.
4. Mark an intersecting line in the center of
each track hole (Figure 2).
5. Take the track down, remove double stick
tape (if used) and set the track aside.
1. To determine where the track should be
installed, rst measure the height of the door,
then add 2-1/8” to the door length. 1/2” will be
for the clearance between the bottom edge of
the door and the oor. 1-5/8” will be from the
top edge of the door to the center of the track.
(Figure 1).
STAG HANGER Assembly Instructions
RUSTICAHARDWARE.com
7
3
03
2017
VERSION
Figure 3
Figure 4
Figure 5
Figure 5A
6. Drill out the marked holes using a drill with a
1/4” drill bit (Figure 3).
9. Install remaining spacers with lag screws
and washers (provided) using a 9/16” socket
wrench (Figure 5). Tighten all lag screws.
7. Attach one end of the track to the wall with
one hard stop, one lag screw, and one washer
(provided) using a socket wrench with 9/16”
socket (Figure 4). Do not tighten.
8. Repeat step 7 for the other end of the track.
10. Stretch rubber bumper (provided)
over hard stop. Repeat for the hard
stop on the other end of the track
(Figure 5A).
STAG HANGER Assembly Instructions
RUSTICAHARDWARE.com
8
3
03
2017
VERSION
�
Figure 6
Figure 7
Figure 8
11. Hang the door (Figure 6).
12. With the door in the closed position, ensure
the door is hanging straight using a bubble
level.
DOOR GUIDE INSTALLATION
13. Position the Door Guide part way into the
groove in the bottom of the door (Figure 7).
14. Install the Door Guide using a 1” phillips
screw (provided) and a drill with a phillips bit.
SUGGESTION:
Use double stick tape on the bottom of the door
guide to hold the guide in place.
15. Slide the door toward the open position un-
til the other side of the Door Guide is exposed.
16. Install the second 1” phillips screw
(provided) using a drill with a phillips bit
(Figure 8).
STAG HANGER Assembly Instructions
RUSTICAHARDWARE.com
9
3
03
2017
VERSION
Figure 9
Figure 10
ANTI-JUMP GUIDE INSTALLATION
SUGGESTION:
Use double stick tape on the back of the anti-jump
bracket to hold it in place on the door.
18. Install the bracket to the door edge with 2
phillips screws (provided) using a drill with a
phillips bit (Figure 9).
17. Place the Anti-Jump bracket on the door
side, moving the bracket up until it is between
1/8” and 1/16” from the bottom edge of the rail.
Mark the placement with a pencil.
19. Repeat steps 17 and 18 for the opposite end
of the door.
ANTI-JUMP BLOCK INSTALLATION FOR BI-PARTING DOORS
20. Place the Anti-Jump block on the top of the
door (Figure 10). Using a drill with a phllips bit,
install the the block with the 1” phillips screw
(provided).
21. Repeat step 20 for the opposite end of the
door.
SUGGESTION:
Use double stick tape on the back of the anti-jump
block to hold it in place on the door.
WE LOVE WHAT YOU ARE
DOING WITH THE PLACE
CONGRATULATIONS ON YOUR DECISION TO BRING HOME
AN AMERICAN MADE PRODUCT OF THE HIGHEST QUALITY.
WE HOPE YOUR Stag Hanger BRINGS ART AND FUNCTION INTO
YOUR LIFE.
Designed and crafted
entirely in the
U.S.A.
don’t be a stranger. follow us
on social media.
support@rusticahardware.com
/
