Hillman 854574 Installation guide

Decorative Sliding

Door Hardware

Installation Manual

2

Ø 10 (3/8")

Ø 8 (5/16")

Ø 10 (3/8")

Ø 6 (1/4")

Ø 5 (7/32")

A

C

(x1)

F

(x2)

E

(x5)

B

(x1)

G

(x1)

I

H

L

D

(x1)

K

(x4)

(x1)

Hardware Included

Tools Required

ST4.2x25 (x4)

M8x90 (x5)

M10x60 (x4)

bolts for 1

3

/4"

(40-45 mm) door

(x2)

N

O

M

M10x55 (x4)

bolts for 1

3

/8"

(35-40 mm) door

(x4)

J

Ø8

3

16"

406 mm

16"

406 mm

16"

406 mm

16"

406 mm

4

3

/4"

120 mm

3

/

8

"

10 mm

1

3

/

4

"

43 mm

+

78

3

/

4

"

2000 mm

78

3

/4"

2000 mm

Required Dimensions

Maximum Loading

Weight: up to 200 lbs

up to 90 kg

Door Width: Up to 36"

Width: Up to 914 mm

Door 1

3

/8" to 1

3

/4"

Thickness: 35 mm to 44 mm

Required Parts (not included)

WARNING: Install a header board above

the door opening to secure the rail.

B

Pre-Installation

4

Installation - Step 2

Installing the rail

• Center the rail

on the header board

using a level and

mark the 5 holes.

B



4

3

/

4

"

120 mm

1

3

/4"

43 mm

2"

50 mm

Ø5.5 (

7

/

32

")

16"

406 mm

16"

406 mm

16"

406 mm

16"

406 mm

H +

Installing the header board

• Determine the height of your door and

position the header board at the desired

location above.

• Use a level to ensure the board is even.

• Use interior screws (not included) to

secure the header board to the wall studs.

Installation - Step 1

B

16"

406 mm

16"

406 mm

16"

406 mm

16"

406 mm

4

3

/4"

120 mm

3

/8"

10 mm

1

3

/

4

"

43 mm

+

78

3

/

4

"

2000 mm

5

Installation - Step 3

• Snap the two rail

pieces together and secure

to the header board using

the fasteners and

spacers . Use the

spacers between the rail

and the header board.

(x5)

Installing the Hangers

• Measure the holes for the rst

hanger approximately 5

7

/8"

(150 mm) from the edge of the

door and approximately 1

5

/8"

(40 mm) from the top.

• Once holes are determined,

mark the door with a pencil

and proceed to drill.

• Proceed to install the hanger by

rst determining the thickness of

the door. If the door is approx-

imately 1

3

/8" (35 mm) thick use

the shorter screws . If the

door is approximately 1

3

/4" (44

mm), use the longer screws

N

.

• Repeat the step on the other side

for the second hanger.

A

O

(x2)

depend on

door depth

or

Ø

(

3

/

8

")

drill out

E

ON

A

B

L

E

6

Installation - Step 5

Door Preparation Guide (If required)

• When using the single oor guide ensure the bottom of the door has a mortise groove.

If the bottom of the door is not centrally mortised, use a router to complete this task.

This will help the door travel smoothly and prevent the door from swinging in and out.

D

1

/4"

6 mm

3

/4"

19 mm

Installing the anti-jump discs

• Place the anti-jump discs a minimum

of 2" (51 mm) away from the inside edge

of the hanger on top of the door. The hole

of the anti-jump disc should be closer to

the front of the door

• Repeat this step on the opposite side

F

(x2)

2"

51 mm

Installation - Step 4

A

F

7

Installation - Step 7

Placing the door on the rail

• Rotate the anti-jump discs out of the way and place the door with hangers installed

on the rail. Ensure the door is level on the rail when installed. Test the door by sliding it.

Once tested, rotate the anti-jump discs back into the original spot.

F

Installing the ﬂoor guide(s)

• Slide the door into an open

position without it falling off

the rail.

• Measure approximately ½"

(12,7mm) from the edge of

the opening and center the

oor guide(s) on the oor

and align with the door.

• Drill holes in the oor and

secure the oor guide(s)

with fasteners.

3 4

1 2

Single Floor Guide

Grooved Door

Double Floor Guide

Ungrooved Door

For Concrete Floors For Non-Concrete Floors

1

/

2

"

12,7 mm

1

/2"

12,7 mm

Installation - Step 6

F

D

C

M

J

M

8

1"

25 mm

+

1"

25 mm

1"

25 mm

Installing the door stops

• Slide the door to the

closed position overlap-

ping the opening by 1"

(25 mm) on both sides.

• Slide the door stop

onto the rail ensuring

it touches the hanger.

Using the Allen Key ,

tighten the screws to

secure the door stop.

• Move the door to the

open position and repeat

the same steps for the

other door stop .

• Install the hole caps

(if needed) in the holes at

the end of the rail.

H

G

I

K

Installation - Step 8

E

G

H I

Hillman 854574 Installation guide

Hillman 854574 Installation guide

Other documents