HySecurity SmartCNX Phone App Quick start guide
- Type
- Quick start guide
SmartCNX Installer App (Android)
QUICK START GUIDE
1
MX4821 Rev. B ©2020 hysecurity.com • 800-321-9947
DC
POWER
SmartCNX CONTROLLER
Connect the SmartCNX installer app to the SmartCNX controller with Bluetooth as described below:
ON
OFF
AC
POWER
DISPLAY
For receiver with jumpers turn on
Bluetooth by placing jumpers as
shown at right.
For receiver with switch, turn on
Bluetooth by placing switch to
ON position.
FIGURE 2: Power Switches &
SmartCNX Controller Locations FIGURE 3: SmartCNX Controller Controls
MENU
OFF
ON
UP
DOWN
SELECT
1. Ensure both AC and DC power switches for the SmartCNX controller are switched to OFF (FIGURE 2).
2. Remove rubber cover from plugin radio slot on the SmartCNX controller (FIGURE 1, left).
3. Depending on the version, either use needle nose pliers to move jumper from pins B&C (FIGURE 1) to pins
A&B to enable wireless communication OR place switch to ON position. Replace rubber cover over slot.
4. Power up SmartCNX Controller by switching both AC and DC switches to ON (FIGURE 2).
5. Press MENU, then press UP to navigate to “EXTERNAL COMMUNICATIONS” (FIGURE 4).
6. Press SELECT, then press DOWN to navigate to “BLE OPTIONS MENU” (FIGURE 4).
7. Press SELECT, then press UP to select “ON”, then press SELECT again to enable Bluetooth.
8. Press UP to obtain Bluetooth PIN and gate name – these are used to connect the app.
FIGURE 4: SmartCNX Controller Menu Navigation to Enable Bluetooth Connectivity
Write down or memorize
gate name and PIN
NETWORK SETUP
MENU HySecurity Gate
GATENAME
0 (OFF)
DHCP
10.3.3.2
IPV4 ADDRESS XX.X.X.X
^
HySecurity Gate
^
255.255.255.0
NETMASK IPV4 XX.X.X.X
^
10.3.3.2
GATEWAY IPV4 XX.X.X.X
^
8.8.8.8
DNS 1 IPV4 XX.X.X.X
^
8.8.4.4
DNS 2 IPV4 XX.X.X.X
^
fec0::2
IPV6 ADDRESS XXXX::X
^
fec0::1
IPV6 ADDRESS XXXX::X
^
2001::4860:4860::
DNS 1 IPV6 XXXX::X
^
2001::4860:4860::
DNS 2 IPV6 XXXX::X
^
0 (NO)
RESET DEFAULTS 0 (NO) / 1 (YES)
RESET DEFAULTS
64
SUBNETLEN IPV6 1-128
SUBNETLEN IPV6
0 (OFF)
1(ON)
DHCP
USB
OPTIONS MENU 0 (NO)
SAVE LOG
0 (NO)
LOAD SW
0 (OFF)
CAPTURE DEBUG 0 (OFF) / 1 (ON)
CAPTURE DEBUG
0 (NO) / 1 (YES)
SAVE LOG
0 (NO)
LOAD SW
BLE
OPTIONS MENU
BLUEBUS
OPTIONS MENU
NONE
BLUEBUS DEVICES
0 (OFF)
SCAN FOR DEVICES
0 (OFF)
SYSTEM ADDRESS 0 (OFF) - 99 (DEBUG OUT)
SYSTEM ADDRESS
0 (OFF) / 1 (ON)
SCAN FOR DEVICES
NONE
BLUEBUS DEVICES
EXTERNAL
COMMUNICATIONS
0 (OFF)
1 (ON)
BLE
OPTIONS MENU BLE ENABLE
NETWORK SETUP
MENU HySecurity Gate
GATENAME
0 (OFF)
DHCP
10.3.3.2
IPV4 ADDRESS XX.X.X.X
^
HySecurity Gate
^
255.255.255.0
NETMASK IPV4 XX.X.X.X
^
10.3.3.2
GATEWAY IPV4 XX.X.X.X
^
8.8.8.8
DNS 1 IPV4 XX.X.X.X
^
8.8.4.4
DNS 2 IPV4 XX.X.X.X
^
fec0::2
IPV6 ADDRESS XXXX::X
^
fec0::1
IPV6 ADDRESS XXXX::X
^
2001::4860:4860::
DNS 1 IPV6 XXXX::X
^
2001::4860:4860::
DNS 2 IPV6 XXXX::X
^
0 (NO)
RESET DEFAULTS 0 (NO) / 1 (YES)
RESET DEFAULTS
64
SUBNETLEN IPV6 1-128
SUBNETLEN IPV6
0 (OFF)
1(ON)
DHCP
USB
OPTIONS MENU 0 (NO)
SAVE LOG
0 (NO)
LOAD SW
0 (OFF)
CAPTURE DEBUG 0 (OFF) / 1 (ON)
CAPTURE DEBUG
0 (NO) / 1 (YES)
SAVE LOG
0 (NO)
LOAD SW
BLE
OPTIONS MENU
BLUEBUS
OPTIONS MENU
NONE
BLUEBUS DEVICES
0 (OFF)
SCAN FOR DEVICES
0 (OFF)
SYSTEM ADDRESS 0 (OFF) - 99 (DEBUG OUT)
SYSTEM ADDRESS
0 (OFF) / 1 (ON)
SCAN FOR DEVICES
NONE
BLUEBUS DEVICES
EXTERNAL
COMMUNICATIONS
0 (OFF)
1 (ON)
BLE
OPTIONS MENU BLE ENABLE
NETWORK SETUP
MENU HySecurity Gate
GATENAME
0 (OFF)
DHCP
10.3.3.2
IPV4 ADDRESS XX.X.X.X
^
HySecurity Gate
^
255.255.255.0
NETMASK IPV4 XX.X.X.X
^
10.3.3.2
GATEWAY IPV4 XX.X.X.X
^
8.8.8.8
DNS 1 IPV4 XX.X.X.X
^
8.8.4.4
DNS 2 IPV4 XX.X.X.X
^
fec0::2
IPV6 ADDRESS XXXX::X
^
fec0::1
IPV6 ADDRESS XXXX::X
^
2001::4860:4860::
DNS 1 IPV6 XXXX::X
^
2001::4860:4860::
DNS 2 IPV6 XXXX::X
^
0 (NO)
RESET DEFAULTS 0 (NO) / 1 (YES)
RESET DEFAULTS
64
SUBNETLEN IPV6 1-128
SUBNETLEN IPV6
0 (OFF)
1(ON)
DHCP
USB
OPTIONS MENU 0 (NO)
SAVE LOG
0 (NO)
LOAD SW
0 (OFF)
CAPTURE DEBUG 0 (OFF) / 1 (ON)
CAPTURE DEBUG
0 (NO) / 1 (YES)
SAVE LOG
0 (NO)
LOAD SW
BLE
OPTIONS MENU
BLUEBUS
OPTIONS MENU
NONE
BLUEBUS DEVICES
0 (OFF)
SCAN FOR DEVICES
0 (OFF)
SYSTEM ADDRESS 0 (OFF) - 99 (DEBUG OUT)
SYSTEM ADDRESS
0 (OFF) / 1 (ON)
SCAN FOR DEVICES
NONE
BLUEBUS DEVICES
EXTERNAL
COMMUNICATIONS
0 (OFF)
1 (ON)
BLE
OPTIONS MENU
BLE ENABLE
NETWORK SETUP
MENU HySecurity Gate
GATENAME
0 (OFF)
DHCP
10.3.3.2
IPV4 ADDRESS XX.X.X.X
^
HySecurity Gate
^
255.255.255.0
NETMASK IPV4 XX.X.X.X
^
10.3.3.2
GATEWAY IPV4 XX.X.X.X
^
8.8.8.8
DNS 1 IPV4 XX.X.X.X
^
8.8.4.4
DNS 2 IPV4 XX.X.X.X
^
fec0::2
IPV6 ADDRESS XXXX::X
^
fec0::1
IPV6 ADDRESS XXXX::X
^
2001::4860:4860::
DNS 1 IPV6 XXXX::X
^
2001::4860:4860::
DNS 2 IPV6 XXXX::X
^
0 (NO)
RESET DEFAULTS 0 (NO) / 1 (YES)
RESET DEFAULTS
64
SUBNETLEN IPV6 1-128
SUBNETLEN IPV6
0 (OFF)
1(ON)
DHCP
USB
OPTIONS MENU 0 (NO)
SAVE LOG
0 (NO)
LOAD SW
0 (OFF)
CAPTURE DEBUG 0 (OFF) / 1 (ON)
CAPTURE DEBUG
0 (NO) / 1 (YES)
SAVE LOG
0 (NO)
LOAD SW
BLE
OPTIONS MENU
BLUEBUS
OPTIONS MENU
NONE
BLUEBUS DEVICES
0 (OFF)
SCAN FOR DEVICES
0 (OFF)
SYSTEM ADDRESS 0 (OFF) - 99 (DEBUG OUT)
SYSTEM ADDRESS
0 (OFF) / 1 (ON)
SCAN FOR DEVICES
NONE
BLUEBUS DEVICES
EXTERNAL
COMMUNICATIONS
0 (OFF)
1 (ON)
BLE
OPTIONS MENU
BLE ENABLE
NETWORK SETUP
MENU HySecurity Gate
GATENAME
0 (OFF)
DHCP
10.3.3.2
IPV4 ADDRESS XX.X.X.X
^
HySecurity Gate
^
255.255.255.0
NETMASK IPV4 XX.X.X.X
^
10.3.3.2
GATEWAY IPV4 XX.X.X.X
^
8.8.8.8
DNS 1 IPV4 XX.X.X.X
^
8.8.4.4
DNS 2 IPV4 XX.X.X.X
^
fec0::2
IPV6 ADDRESS XXXX::X
^
fec0::1
IPV6 ADDRESS XXXX::X
^
2001::4860:4860::
DNS 1 IPV6 XXXX::X
^
2001::4860:4860::
DNS 2 IPV6 XXXX::X
^
0 (NO)
RESET DEFAULTS 0 (NO) / 1 (YES)
RESET DEFAULTS
64
SUBNETLEN IPV6 1-128
SUBNETLEN IPV6
0 (OFF)
1(ON)
DHCP
USB
OPTIONS MENU 0 (NO)
SAVE LOG
0 (NO)
LOAD SW
0 (OFF)
CAPTURE DEBUG 0 (OFF) / 1 (ON)
CAPTURE DEBUG
0 (NO) / 1 (YES)
SAVE LOG
0 (NO)
LOAD SW
BLE
OPTIONS MENU
BLUEBUS
OPTIONS MENU
NONE
BLUEBUS DEVICES
0 (OFF)
SCAN FOR DEVICES
0 (OFF)
SYSTEM ADDRESS 0 (OFF) - 99 (DEBUG OUT)
SYSTEM ADDRESS
0 (OFF) / 1 (ON)
SCAN FOR DEVICES
NONE
BLUEBUS DEVICES
EXTERNAL
COMMUNICATIONS
0 (OFF)
1 (ON)
BLE
OPTIONS MENU BLE ENABLE
GATE NAME
BLE PIN: 123456
GATE NAME
BLE PIN: 123456
5
4
1
6 7
7 8
HYSECURITY
GATE CLOSED
HYSECURITY
GATE CLOSED
HYSECURITY
GATE CLOSED
FIGURE 1: Enabling Bluetooth on the SmartCNX Controller
2
3
C
C
B
B
A
A
C
B
A
ON OFF
Jumper Pins
Switch
SmartCNX Installer App (Android)
QUICK START GUIDE
2 hysecurity.com • 800-321-9947 MX4821 Rev. B ©2020
9. Optional: Press MENU Button (3) times to verify Bluetooth connectivity with Bluetooth symbol (FIGURE 4).
10. To ensure the latest version of the SmartCNX Installer app is installed on your phone, download the latest
version of the app from the Play Store.
11. On the phone, click the HySecurity SmartCNX icon to open the application.
12. Tap “Connect”.
13. Tap the desired gate name from the list of available gate names that appear.
14. At the prompt, enter the PIN that was shown in the CNX controller display in STEP 8.
15. Top left “Connect” button turns green if correct PIN was entered and to indicate a successful connection.
NOTES:
• If there are connectivity problems, refer to the Troubleshooting Connectivity Problems table below.
• The PIN is xed and unique for each Smart CNX Control Board and cannot be changed.
• The SmartCNX installer app is for installation only. For added security Bluetooth will turn o automatically
at midnight.
• For added security remove the Bluetooth Jumper (STEP 3) to physically remove power from Bluetooth radio.
TROUBLESHOOTING CONNECTIVITY PROBLEMS
PROBLEM SOLUTION
Gate name does
not appear when
clicking “Connect”
on SmartCNX
installer app.
Make sure Bluetooth is enabled by following STEPS 1-10. Check for the Blutooth symbol when
exiting the menus (see STEP 8).
Check if Bluetooth jumper is connected. Jumper located under the OXI port on the Smart CNX
Controler. Jumpers need to be inserted across the A & B pins (FIGURE 1) to enable Bluetooth.
Please call 800-321-9947 or email appsupport@hysecurity.com for more help and/or suggestions.
11 12 13 14 15
Choose Controller Enter PIN ConnectedTap ConnectOpen App
FIGURE 5: SmartCNX Installer Application Connectivity Screens
Bluetooth
SYMBOL
-- END --
HYSECURITY
GATE CLOSED
FIGURE 4: Bluetooth Enabled
9
-
1
-
2
HySecurity SmartCNX Phone App Quick start guide
- Type
- Quick start guide
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
HySecurity HTG 316 Relay Owner's manual
-
-
-
-
-
-
-
-
-
Other documents
-
Nice HySecurity SlideSmart CNX Slide Gate Operator Installation guide
-
Nice HySecurity SwingSmart CNX Swing Gate Operator Installation guide
-
Nice HySecurity SwingSmart CNX 20 User manual
-
Vgate vLinker FD+ BT 4.0 Professional OBD2 Diagnostic Tools Auto Scanner for Android for iOS User guide
-
Nice Apollo CBOX1050 Control Box Kit User manual
-
-
-
-
-
Draytek VigorNIC 132 Series User manual
