Mettler Toledo Ex-Classification InPro 7100i Series Conductivity Sensors Technical Specifications

Ex Classication

InPro 7100 i Series

Conductivity Sensors

InPro 7100 i Series

30 018 487

cs Klasikace Ex 2

da Ex-klassicering 4

de Ex-Klassikation 6

en Ex Classication 8

es ClasicaciónEx 10

 Ex-luokittelu 12

fr Classication Ex 14

hu Ex-besorolás 16

it Classicazione Ex 18

ja 20

ko Ex 22

nl Ex-classicatie 24

pl Klasykacja Ex 26

pt Ex-Classicação 28

ru Класс взрывобезопасности 30

sv Ex-klassning 32

th Ex Classication 34

zh 36

Page is loading ...

8 InPro 7100 i Series

InPro 7100 i Series © 02 / 16 Mettler-Toledo GmbH

30 018 487 Printed in USA

en

1 Introduction

In accordance with Directive RL 94/9/EC (ATEX

95) Annex I, the InPro

®

7100 i/12/***/**** con-

ductivity sensor is classied in Device Group II

Category 1/2 G, which according to Directive

RL99/92/EC (ATEX 137) may be used in zones

0/1 or 0/2 or 1 or 2 as well as gas groups IIA and

IIB, which have potentially explosive atmospheres

due to combustible materials in the range of tem-

perature classes T1 to T6.

It must be installed and used in compliance with

the requirements of EN 60079-14.

The ISM measurement circuit is part of a common

intrinsically safe system and is connected to and

operated with a separately certied transmitter.

As part of an intrinsically safe system, the ISM

®

measurement circuit has safe galvanic isolation

at the transmitter from circuits that are not intrin-

sically safe up to the peak value of a nominal

voltage of 375 V and from earthed parts up to the

peak value of a nominal voltage of 30 V.

2 Rated parameters

Measuring and supply circuit:

With type of protection intrinsic safety Ex ia IIB.

Only for connection to certied intrinsically safe

circuits

Maximum values:

U

i

≤16 V, I

i

≤ 30 mA, P

i

≤ 50 mW

L

i

= 0.002 μH (effective internal inductance)

C

i

= 0.0015 μF (effective internal capacitance)

3 Special conditions

3.1 The maximum permissible process temperatures

with corresponding temperature classes are

shown in the following table:

Temperature Max. permissible

class process temperature

T6 62 °C

T5 74 °C

T4 102 °C

T3 130 °C

Ex classication II 1/2G Ex ia IIB T6/T5/T4/T3 Ga/Gb

in accordance with test certication

SEV 10 ATEX 0137 X

en Ex-Classication

InPro 7100 i Series 9

InPro 7100 i Series © 02 / 16 Mettler-Toledo GmbH

30 018 487 Printed in USA

en

3.2 The permissible external ambient temperature

range in the area of the connector head is – 20 °C

to + 50 °C.

3.3 The conductivity sensor InPro 7100 i/12/***/****

must only be used in suitable process connectors

of METTLER TOLEDO or other manufacturers in

potentially explosive areas.

3.4 The capacitance and inductance of the connect-

ing cable must be taken into account in the di-

mensioning.

3.5 In areas with potentially explosive atmospheres,

InPro 7100 i/12/***/**** conductivity sensor

can be used in / with the InFit

®

76*-*** or

InTrac

®

7**-*** ttings or in / with other suitable

ttings.

If necessary, this tting must be included in the

periodic pressure testing of the system or facility.

3.6 The independent process tting used for the in-

stallation of the conductivity sensor must be elec-

trically connected to the potential equalization

system of the system or facility, and if necessary

it must be included in the periodic pressure testing

of the system or facility.

3.7 To ensure safe working conditions in areas with

potentially explosive atmospheres, the minimum

conductivity of the media must always be greater

than 1 nS / cm.

InPro, InFit, InTrac and ISM are registered trade-

marks of Mettler-Toledo GmbH in Switzerland,

USA, European Union and a further ve countries.

Ex classication II 1/2G Ex ia IIB T6/T5/T4/T3 Ga/Gb

in accordance with test certication

SEV 10 ATEX 0137 X

Page is loading ...

38 InPro 7100 i Series

30 018 487 Printed in USA

Notes

InPro 7100 i Series 39

30 018 487 Printed in USA

Notes

Brazil Mettler-Toledo Ind. e Com. Ltda.

Avenida Tamboré, 418 – Tamboré,

BR - 06460-000 Barueri / SP, Brazil

Phone +55 11 4166 7400

e-mail mettler@mettler.com.br;

service@mettler.com.br

France Mettler-Toledo

Analyse Industrielle S.A.S.

30, Bld. de Douaumont, FR - 75017

Paris, France

Phone +33 1 47 37 06 00

e-mail mtpro-[email protected]

Germany Mettler-Toledo GmbH

Prozeßanalytik, Ockerweg 3,

DE - 35396 Gießen

Phone +49 641 507-444

e-mail prozess@mt.com

Switzerland Mettler-Toledo (Schweiz) GmbH

Im Langacher, CH - 8606 Greifensee

Phone +41 44 944 47 60

e-mail ProSupport.ch@mt.com

United States METTLER TOLEDO

Process Analytics

900 Middlesex Turnpike, Bld. 8,

Billerica, MA 01821, USA

Phone +1 781 301 8800

Freephone +1 800 352 8763 (only USA)

e-mail mtprou[email protected]

For more addresses of METTLER TOLEDO Market

Organizations please go to:

www.mt.com/pro-MOs

Mettler-Toledo GmbH

Process Analytics, Im Hackacker 15, CH - 8902 Urdorf

Phone +41 44 729 62 11, Fax +41 44 729 66 36

Subject to technical changes

Printed in USA. 30 018 487

www.mt.com/pro

Mettler Toledo Ex-Classification InPro 7100i Series Conductivity Sensors Technical Specifications

Mettler Toledo Ex-Classification InPro 7100i Series Conductivity Sensors Technical Specifications

in other languages

Related papers

Other documents