2. Crystorama
  3. KEN-8304-BF
KEN-8304-BF

Crystorama KEN-8304-BF User manual

  • Hello! I've reviewed the assembly instruction for the Crystorama light fixture, model KEN-8304-BF. This document provides step-by-step instructions on how to assemble the light, including attaching the glass components, connecting the rods, and securing it to the outlet box. I'm ready to answer any questions you might have about assembling this light.
  • What type of bulb is required?
    Is this light suitable for damp locations?
    What is maximum wattage of bulbs?
ASSEMBLYINSTRUCTIONMODEL#KEN-8304-BF
CRYST
RAMA
WARNING:
ElectricalDanger TurnPoweroff
WARNING: ThisproductcanexposeyoutoLead
whichisknowntothestateofCaliforniatocausecancer
and/orbirthdefectsorreproductiveharm.Formore
informationgotowww.P65Warnings.ca.gov
L I G H T I N GT H EW A YF O RS I X T YY E A R S
installedbyalicensedelectrician
inaccordancewiththeNational
Allelectricalcomponentsmustbe
ElectricCodeandtheappropriate
localelectricalcodes.
1Pc
3Pcs
ROD2=
ROD1=
6”
12”
ROD2
ROD1
5-7/8’’
22-1/2’’
62-1/2’’
18-1/4’’
20-5/8’’
3-1/8’’
3-7/8’’
15-1/4’’
GLASSPANEL
GLASSDIFFUSER
1’’
CLIP
SCREWS
CLIP
METALFRAME
GLASSDIFFUSER
GLASSPANEL
(4PCS)
TOPMETALRING
SOCKET
LIGHTCLUSTER
CENTER
ROD
HANGINGROD
SCREW
COUPLER ROD
Howtoinstall
8.Determinethepreferredhangingheightandadjustthe
requiredrods.
10.Slipcanopykitalongwireandthreaditintothetopofthe
rodassembly.
12.Installthebulb(notincluded)intothesocket.
9.Feedthewiresthroughtherodsandconnectthemtogether.
6.Separatethemountingplatefromthecanopykitbyremoving
thescrews.
7.Installthemountingplatetotheoutletboxusingtwooutlet
boxscrews.
11.Installcanopyontothemountingplate,andsecurewiththe
mountingscrews.
This fixture is Damp rated
Youwillneed4-MediumBaseBulb
60WattsRecommended100WattsMax.
USELEDBULBSFOREXTENDEDUSE
1.Slidetheglassdiffuserontothebottomofmetalframeand
secureitwithclips.
2.Slidetheglasspanelsinsidethemetalframeandsecureit
withclips.
3.Slipthecenterrodassemblyalongwireandthreadontothe
nipplelocatedonthetopofthelightcluster.
4.Insertthehangingrodintothesideholesoftopboxonthe
centerrod,andsecurethehangingrodfromthetopwiththe
screws.
5.Putthetopmetalringoverthemetalframe.Lineupthehole
onthebottomofhangingrodwiththeholeonthetopmetal
ringandthebracketonthemetalframe,and secureitwith
screws.
BRACKET
Crystorama.com
CRYST
RAMA
L I G H T I N GT H EW A YF O RS I X T YY E A R S
PartNumber
PartNumbers
A.(1)-Mountinghardware
C.(1)-CanopykitW5-7/8’’xH1’’ #XRF8303BFCAN5.875IN
G.(1)-Coupler
F.(3)-RodD5/8’’xL12’’ #XRF8303BFROD12IN
D.(2)-Mountingscrew
E.(1)-RodD5/8’’xL6’’ #XRF8303BFROD6IN
ASSEMBLYINSTRUCTIONMODEL#KEN-8304-BF
I.(1)-Centerrodassembly#XRF8304BFSTEM
B.(1)-Mountingplate
J.(4)-HangingrodD3/8’’xH12-1/8’’ #XRF8304BFSIDEROD
K.(1)-Lightcluster
L.(1)-Topmetalring
M.(4)-Glasspanel
N.(1)-Glassdiffuser#XRF8304DIFF20.625IN
O.(1)-Metalframe
P.(4)-Screw
C
B
A
D
E
F
H
J
I
K
L
M
N
O
P
H.(4)-Screw
G
Crystorama.com
/