2. Crystorama
  3. DAN-404-VG
DAN-404-VG

Crystorama DAN-404-VG User manual

  • Hello! I'm your chat assistant and I've reviewed the assembly instructions for the Crystorama DAN-404-VG light. This document details how to install the light, including securing the fabric shade and connecting the electrical components. I'm ready to answer your questions about the installation process for this light fixture.
  • What type of bulbs are required?
    What is the recommended and maximum wattage for the bulbs?
    Is this fixture suitable for wet locations?
ASSEMBLYINSTRUCTIONMODEL#DAN-404-VG
CRYST
RAMA
WARNING:
ElectricalDanger TurnPoweroff
WARNING: ThisproductcanexposeyoutoLead
whichisknowntothestateofCaliforniatocausecancer
and/orbirthdefectsorreproductiveharm.Formore
informationgotowww.P65Warnings.ca.gov
L I G H T I N GT H EW A YF O RS I X T YY E A R S
installedbyalicensedelectrician
inaccordancewiththeNational
Allelectricalcomponentsmustbe
ElectricCodeandtheappropriate
localelectricalcodes.
6”
12”
1Pc
3Pcs
ROD2=
ROD1=
Howtoinstall
Crystorama.com
3.Determinethepreferredhangingheightandadjust
therequiredrods.
5.Slipcanopykitalongwireandthreaditintothetop
oftherodassembly.
8.Installthebulbs(notincluded)intothesocket.
4.Feedthewiresthroughtherodsandconnectthem
together.
Youwillneed4-CandelabraBaseBulb
40WattsRecommended60WattsMax.
USELEDBULBSFOREXTENDEDUSE
This fixture is Dry rated
5-7/8”
1”
13”
16-3/4”
FABRICSHADE 9-3/4”
16-1/4”
ROD1
ROD2
57-3/4”
ROD
COUPLING
FABRICSHADE
CENTER
ROD
LIGHTCLUSTER
CLIP
METALFRAME
CANDLESLEEVE
1.Slipthecenterrodassemblyalongwireandthread
ontothenipplelocatedonthetopofthelightcluster.
2.Slidethefabricshadeinsidethemetalframeand
secureitwithclips.
6.Installthemountingscrewsintothematching
holesinthemountingbar.Securethemounting
bartotheoutletboxwiththeoutletboxscrews.
7.Raisecanopyallowingthemountingscrewsto
protrudethroughtheholesinthecanopy,and
securewiththeballnut.
NOTE : HIDETHESEAMSOFTHESHADEBYALIGNING
ITWITHAVERTICALMETALBAR.
CRYST
RAMA
L I G H T I N GT H EW A YF O RS I X T YY E A R S
PartNumber
PartNumbers
A.(1)-Mountinghardware
B.(1)-CanopykitW5-7/8’’xH1’’ #XRF404VGCAN5.875IN
F.(1)-CenterrodW1/2’’xL7-1/4’’ #XRF404VGSTEM7.25IN
E.(3)-RodD5/8’’xL12’’ #XRF404VGROD12IN
C.(2)-Ballnut#XRF400VGBANUT
D.(1)-RodD5/8’’xL6’’ #XRF404VGROD6IN
ASSEMBLYINSTRUCTIONMODEL#DAN-404-VG
H.(4)-CandlesleeveW7/8’’xL2’’
Crystorama.com
A
B
C
D
E
F
G
H
I
G.(1)-FabricshadeW16-1/4’’xH9-3/4’’ #XRF404SHA16.25IN
I.(1)-Metalframe
/