2. Crystorama
  3. DAN-406-PN
DAN-406-PN

Crystorama DAN-406-PN User manual

  • Hello! I've reviewed the assembly instructions for the Crystorama DAN-406-PN Light. This document details the steps for safely assembling and installing the fixture, including the connections, bulb requirements, and the use of the fabric shade and metal frame. I'm ready to answer any questions you have about this product.
  • What type of bulbs are needed for this fixture?
    What is the recommended wattage for the bulbs?
    Is it safe to install this fixture on my own?
    What is the product rated for?
ASSEMBLYINSTRUCTIONMODEL#DAN-406-PN
CRYST
RAMA
WARNING:
ElectricalDanger TurnPoweroff
WARNING: ThisproductcanexposeyoutoLead
whichisknowntothestateofCaliforniatocausecancer
and/orbirthdefectsorreproductiveharm.Formore
informationgotowww.P65Warnings.ca.gov
L I G H T I N GT H EW A YF O RS I X T YY E A R S
installedbyalicensedelectrician
inaccordancewiththeNational
Allelectricalcomponentsmustbe
ElectricCodeandtheappropriate
localelectricalcodes.
6”
12”
1Pc
3Pcs
ROD2=
ROD1=
Howtoinstall
Crystorama.com
3.Determinethepreferredhangingheightandadjust
therequiredrods.
5.Slipcanopykitalongwireandthreaditintothetop
oftherodassembly.
8.Installthebulbs(notincluded)intothesocket.
4.Feedthewiresthroughtherodsandconnectthem
together.
Youwillneed6-CandelabraBaseBulb
40WattsRecommended60WattsMax.
USELEDBULBSFOREXTENDEDUSE
This fixture is Dry rated
5-7/8”
1”
17”
24-3/4”
FABRICSHADE 13-1/4”
24-1/4”
ROD1
ROD2
61-3/4”
ROD
COUPLING
FABRICSHADE
CENTER
ROD
LIGHTCLUSTER
CLIP
METALFRAME
CANDLESLEEVE
1.Slipthecenterrodassemblyalongwireandthread
ontothenipplelocatedonthetopofthelightcluster.
2.Slidethefabricshadeinsidethemetalframeand
secureitwithclips.
6.Installthemountingscrewsintothematching
holesinthemountingbar.Securethemounting
bartotheoutletboxwiththeoutletboxscrews.
7.Raisecanopyallowingthemountingscrewsto
protrudethroughtheholesinthecanopy,and
securewiththeballnut.
NOTE : HIDETHESEAMSOFTHESHADEBYALIGNING
ITWITHAVERTICALMETALBAR.
CRYST
RAMA
L I G H T I N GT H EW A YF O RS I X T YY E A R S
PartNumber
PartNumbers
A.(1)-Mountinghardware
B.(1)-CanopykitW5-7/8’’xH1’’ #XRF404PNCAN5.875IN
F.(1)-CenterrodW1/2’’xL9-1/4’’ #XRF406PNSTEM9.25IN
E.(3)-RodD5/8’’xL12’’ #XRF404PNROD12IN
C.(2)-Ballnut#XRF400PNBANUT
D.(1)-RodD5/8’’xL6’’ #XRF404PNROD6IN
ASSEMBLYINSTRUCTIONMODEL#DAN-406-PN
H.(6)-CandlesleeveW7/8’’xL2-3/8’’
Crystorama.com
A
B
C
D
E
F
G
H
I
G.(1)-FabricshadeW24-1/4’’xH13-1/4’’ #XRF406SHA24.25IN
I.(1)-Metalframe
/