2. Crystorama
  3. 297-PN
297-PN

Crystorama 297-PN User manual

  • Hello! I've reviewed the assembly instructions for the Crystorama 297-PN light fixture. This document provides a detailed guide on how to properly install the fixture, including wiring, shade attachment, and bulb replacement. I'm ready to answer any questions you may have about the product and its assembly process.
  • What type of bulbs are required?
    Is this fixture suitable for wet locations?
    How do I replace the bulb?
ASSEMBLYINSTRUCTIONMODEL#297-PN
CRYST
RAMA
WARNING:
ElectricalDanger TurnPoweroff
WARNING: ThisproductcanexposeyoutoLead
whichisknowntothestateofCaliforniatocausecancer
and/orbirthdefectsorreproductiveharm.Formore
informationgotowww.P65Warnings.ca.gov
L I G H T I N GT H EW A YF O RS I X T YY E A R S
installedbyalicensedelectrician
inaccordancewiththeNational
Allelectricalcomponentsmustbe
ElectricCodeandtheappropriate
localelectricalcodes.
Youwillneed5-MediumBaseBulb
60WattsRecommended100WattsMax.
USELEDBULBSFOREXTENDEDUSE
Howtoinstall
Crystorama.com
This fixture is Dry rated
3.Determinethepreferredhangingheightandadjust
therequiredrods.
5.Slipcanopykitalongwireandthreaditintothetop
oftherodassembly.
7.Installthebulb(notincluded)intothesocket.
4.Feedthewiresthroughtherodsandconnectthem
together.
1.Separatethemountingplatefromthecanopykitby
removingthescrews.
2.Installthemountingplatetotheoutletboxusing
twooutletboxscrews.
6.Installcanopyontothemountingplate,andsecure
withthemountingscrews.
TOPSHADE
BOTTOMSHADE
METALRING
(IFREPLACEDFROMTHEBOTTOM,YOUNEEDTOREMOVE
THEBOTTOMFINIALANDDIFFUSERTOREPLACETHEBULB.)
FROMTHETOPOPENINGOFSHADE,REPLACEPREVIOUS
BULBW/NEWBULB.
HOWTOREPLACEBULB:
5-7/8”
7/8”
14-1/2”
23”
ROD1
ROD2
6”
12”
1Pc
3Pcs
ROD2=
ROD1=
TOPSHADE
BOTTOMSHADE
22-3/4”
22-3/4”
7”
7”
54-3/4”
22-1/8”
GLASSDIFFUSER
8.Threadthenippleontothecouplingandadjust
thelengthofnippletofitwiththeglass.Tighten
itwithhexnut.
9.Slidetheglassdiffuserandtheplasticwasherover
thenipple,thensecurewiththebottomfinial.
NIPPLE
TOPCOUPLING
BOTTOMCOUPLING
HEXNUT
SOCKET
GLASSDIFFUSER
PLASTICWASHER
FINIAL
ROD
CYLINDERNUT
CRYST
RAMA
L I G H T I N GT H EW A YF O RS I X T YY E A R S
ASSEMBLYINSTRUCTIONMODEL#297-PN
Crystorama.com
A
B
CD
E
F
G
H
I
JK
L
M
N
O
PartNumber
PartNumbers
A.(1)-Mountinghardware
B.(1)-Mountingplate
G.(1)-TopshadeW22-3/4’’xH7’’ #XRF297PNSHA22.75IN
F.(3)-RodD5/8’’xL12’’ #XRF290PNROD12IN
C.(2)-mountingscrew
E.(1)-RodD5/8’’xL6’’ #XRF290PNROD6IN
I.(1)-BottomshadeW22-3/4’’xH7’’ #XRF297PNBOTSHA22.75IN
D.(1)-CanopykitW5-7/8’’xH7/8’’ #XRF290PNCAN5.875IN
H.(6)-Cylindernut
K.(1)-Hexnut
O.(1)-Bottomfinial#XRF293PNFIN
M.(1)-Glassdiffuser#XRF297DIF22.125IN
L.(1)-Nipple
N.(1)-Plasticwasher
J.(1)-Metalring
/