ESL VISION ESL-FLD-5090W-13050-WH Installation guide

ESL-FLD-5090W-13050-WH
Brand
ESL VISION
Model
ESL-FLD-5090W-13050-WH
Type
Installation guide
FLOODLIGHT SERIES
Installation Guide Page 1 of 2
1. To avoid electric shock, disconnect power at source prior to installation.
2. The installation should be performed by qualified electricians or lighting technicians.
3. Before conducting any installation, maintenance, or removal, disable all power.
4. Do not touch the fixture while it is in service.
5. If there is any problem with the fixture, turn off power and DO NOT attempt repair unless
you are a qualified technician.
WARNING
Copyright © 2022 ESL Vision, LLC. All rights reserved. Rev: 08/27/22
2Make the wiring connections
as shown in Wiring Diagram 1.
If dimming is not required, make
sure the dimming leads are capped.
G
N
LBLACK
GREY
GREEN FIXTURE
PURPLE
PINKDIM-
DIM+
2Make the wiring connections
as shown in Wiring Diagram 1.
If dimming is not required, make
sure the dimming leads are capped.
G
N
LBLACK
GREY
GREEN FIXTURE
PURPLE
PINKDIM-
DIM+
2Slide the slipfitter into the pole,
making sure that no wires are
pinched. Tighten the set screws
securely to lock the slip fitter in
place.
3To aim the fixture, use a hex
key to loosen the screw. Move
the fixture head to the appropriate
position and tighten the screw to
lock it in position.
3To aim the fixture, use a
screwdriver to loosen the
machine screw. Move the fixture
head to the appropriate position and
tighten the screw to lock it in position.
3To aim the fixture, use a hex
key to loosen the machine
screw. Move the fixture head to the
appropriate position and tighten the
screw to lock it in position.
Knuckle Mount Installation
Trunnion Mount Installation
Slipfitter Mount Installation
1Feed the power cord into the
junction box or conduit. If j-box
mounted, insert the threaded
portion of the knuckle into the
desired knock-out.
1Mount the fixture to the
desired surface. Feed the
power cable to a junction box or
other wiring compartment.
G
N
LBLACK
GREY
GREEN FIXTURE
PURPLE
PINKDIM-
DIM+
1Make the wiring connections
as shown in Wiring Diagram 1.
If dimming is not required, make
sure the dimming leads are capped.
4Restore power and check that
the fixture is working properly.
4Restore power and check that
the fixture is working properly.
4Restore power and check that
the fixture is working properly.
FLOODLIGHT SERIES
Installation Guide Page 2 of 2
Copyright © 2022 ESL Vision, LLC. All rights reserved. Rev: 08/27/22
Wiring Diagram 1
Field Selectable Wattage and CCT
Removable On/O Photocell
1Remove the conduit plug as shown and
set to the desired CCT / wattage. Replace
the conduit plug securely to avoid water
entry into the fixture.
1Remove the photocell conduit cap from
the lamp.
2For CCT tuning, adjust the slide switch to
the desired kelvin setting as shown above.
G
N
LBLACK
GREY
GREEN FIXTURE
PURPLE
PINKDIM-
DIM+
5000K 4000K 3000K
HI MED LOW
2To enable or disable the photocell, use
the integrated On/Off switch. 3To remove and replace, unplug the connected
wires from the back of the Photocell.
3For wattage tuning, adjust the slide switch
to the desired setting as shown above.
35W25W15W
90W70W50W
150W120W105W
ESL-FLD-1535W
ESL-FLD-5090W
ESL-FLD-105150W
On/O switch
Note: Dimming wires must
be capped if not in use.
  • Page 1 1
  • Page 2 2

ESL VISION ESL-FLD-5090W-13050-WH Installation guide

ESL-FLD-5090W-13050-WH
Brand
ESL VISION
Model
ESL-FLD-5090W-13050-WH
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents