Beghelli Acciaio® Eco BX910LED Installation guide

Beghelli
Brand
Beghelli
Model
Acciaio® Eco BX910LED
Type
Installation guide
Page 1 of 2
Beghelli U.S.A., 3810 Executive Way, Miramar, Florida, Tel: (954) 442-6600
09/22/23
ACCIAIO® ECO BX910LED
INSTALLATION INSTRUCTIONS
IMPORTANT SAFEGUARDS
When using electrical equipment basic safety precautions should always be followed including the following:
READ AND FOLLOW ALL SAFETY INSTRUCTIONS:
1. CAUTION! ALWAYS MAKE SURE THE POWER IS TURNED OFF before starting installation.
2. Measure, locate xture’s position, and mark locations for the brackets.
3. Secure brackets to ceiling as shown below. (HARDWARE BY OTHERS)
4. Wiring xture to power supply, shall be performed by a certied electrician, and wired in a manner that complies with
all national electrical codes, as well as the manufacturer’s wiring diagram.
5. Proper replacement of a part removed for user maintenance.
SAVE THESE INSTRUCTIONS!
INSTALLATION
DIMMING WIRING DIAGRAM: SURFACE MOUNT (SM)
SAVE THESE INSTRUCTIONS!
0-10V LEAD / DALI
VIOLET......(DIM +)
GRAY.........(DIM -)
NOTE:
- Optional 3-conductor cord
available (contact factory)
1. 0-10V dimming wires must be run from a dierent conduit out
of the J-box.
AC LEADS
BLACK......(HOT)
WHITE.......(NEUTRAL)
GREEN......(GROUND)
Surface Mounting Clip
Safety Cable
Safety Cable must be
installed where mounting
bracket used
Mounting Bracket
J-BOX (BY OTHERS)
CANOPY KIT
(BY OTHERS)
(BY OTHERS)
MOUNTING HARDWARE
(BY OTHERS)
MOUNTING BRACKET
SURFACE MTG. CLIP
SCREWS & WASHERS
CEILING (CEILING'S STRUCTURE SHOULD BE
ADEQUATE TO SUPPORT THE WEIGHT OF
FIXTURE)
18/3 OR 18/ 5
POWER CORD
Page 2 of 2
Beghelli U.S.A., 3810 Executive Way, Miramar, Florida, Tel: (954) 442-6600
09/22/23
ACCIAIO® ECO BX910LED
INSTALLATION INSTRUCTIONS
A/C CABLE (AC):
1. Attach cable glider to surface mounting clip using provided lock nut
as shown
2. Snap assembled surface mounting clip onto mounting bracket on
the top of the housing until the anges hook onto the bracket.
3. Thread the A/C Cable through the cable glider as shown. (Push top
sleeve of cable glider to release lock and adjust level.)
CHAIN (CH):
1. Insert the hook clip through the loop of the chain.
2. Attach hook clip onto the holes on the side of the bracket on the top
of the housing as shown.
PENDANT KIT:
1. Attach the stem adaptor cap to the surface mounting clip using
provided lock nut as shown.
2. Snap assembled surface mounting clip onto mounting bracket on
the top of the housing until the anges hook onto the bracket.
3. Attach stem adapter & stem to the adapter cap as shown.
PIVOT MOUNT (PM):
1. Attach the pivot bracket to the mounting bracket on the top housing
using provided screw and lock nut as shown.
2. Attach assembly to the wall as shown (hardware by others).
3. To adjust aiming angle, remove adjusting screw, reposition to the
new angle and re-install screw to lock in position.
TRUNNION MOUNT (TM):
1. Attach the trunion bracket to the mounting brackets as shown.
2. Snap the xture onto the bracket assembly as shown.
CH
AC
PENDANT
KIT
PM
TM
A/C Cable
Cable Glider
Surface
Mounting Clip
Mounting
Bracket
Lock Nut
Chain
Mounting
Bracket
Hook Clip
Stem
Stem Adapter
Stem Adapter
Cap
Mounting
Bracket
Lock Nut
Surface
Mounting Clip
Screw and Washer
(by others)
Lock Nut Pivot Bracket
Screw
Mounting Bracket
Adjusting Screw
Anchor
(by others)
Trunnion
Bracket
Lock Nut
Mounting
Bracket
Screw
  • Page 1 1
  • Page 2 2

Beghelli Acciaio® Eco BX910LED Installation guide

Beghelli
Brand
Beghelli
Model
Acciaio® Eco BX910LED
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents