Quantum5x QR-2000 Operating instructions

Brand
Quantum5x
Model
QR-2000
Type
Operating instructions
30ADELAIDESTREETNORTHSUITE12
LONDONONTARIOCANADAN6B3N5
WWW.QUANTUM5X.COMINFO@QUANTUM5X.COM
PH:519-675-6999FAX:519-667-2162
QR-2000
OPERATINGMANUAL
CE
TRUEDIVERSITYRECEIVER
TM
TM
INTRODUCTION
Congratulationandthankyouforthepurchaseofoneofthesestate-of-the-art
PLL Synthesized1000channelsfrequencyagileUHFprofessionalwirelesssystems.
Thefollowingtablegivesanoverviewoftheindividualsystem.
.
11
System Overview
As this is a shared operating manual, please read it thoroughly to familiarize with the
functionofeachpartbeforeuse.
QR-2000
No. Of Channel
Frequency Band
Receiving Mode
AC Adapter
Size
UHF
12-15 / 1500 mA
2*1000
2
Casing
Metal
Receiver LCD Color
White in Blue LCD
Models
No. of Receiver
19"
True Diversity
TheVolumeControlofthereceiverissettoohigh,itmayover-drivetheinputofthe
mixer,causingdistortion.Conversely,ifthereceiveroutputis settoolow,theoverall
signaltonoiseratioofthesystemmaybereduced. Adjusttheoutputlevelofthereceiver
suchthathighestsoundpressurelevelgoingintothemicrophonecausesnoinput
overloadinthemixer,andyetpermitsthemixerlevelcontrolstooperateintheirnormal
range(nottoohighortoolow).
Thisprovidestheoptimumsignaltonoisefortheentiresystem.
ThefunctionsofUSBport
THISFUNCTIONISNOT OPERATIONAL AT THIS TIME
SCAN function
THISFUNCTIONISNOT OPERATIONAL
FORFUTUREUSEONLY
RFInterference
If you encounter receiving interference (from other than an operating TV station), often it
can be overcome by adjusting the receiver's squelch control, as described on below.
Please note that wireless frequencies are shared with other radio services. According to
FCC requlations, wireless microphone operations are unprotected from interference
from other licensed operations in the band. If any interference is received by any
Government or non-Government operation, the wireless microphone must cease
operation. TheabovestatementisvalidintheU.S.A.
ReceiverSquelchsetting
The squelch control setting is per LCD display on the front panel of the receiver is preset
at the factory, but can be adjusted if you must use the system in a high RF interference
area. If there is audio output from the receiver when your transmitter is OFF, adjust the
squelch control so the system will receive the signal from your transmitter but squelch
or eliminate the unwanted background RF noise. This adjustment can cause a reduction
in usable range of the wireless transmitter, so set the control to the lowest position which
reliablymutestheunwantedRFsignal.
RACKMOUNTING
1. If external antenna is used, low loss RF shielded cable should be used and the length
ofthecable
shouldnotexceed3m.
2.Donotplacethereceiveantennawithin1mofanotherreceiverorantenna.
3. Thereceiverantennashouldbekeptawayfromanymetalsurface.
TIPS TO OBTAIN THE BEST RESULTS
FOR A WIRELESS MICROPHONE SYSTEM
REMARKS
QR-2000RECEIVER
6 6 66 6 6
67 8 9 14 15 16 17
ANT.A
ANT.B
ACINPUT
100V-240V
DCIN
12V-15V
BALANCED
AFOUT
MIC LINE
Fig.5
Fig.6
BALANCED
AFOUT
MIC LINE
1. Slot for front mount Antenna
2. Power switch
3. LCD Display
4.
UP button
5. DOWN button
6.
7.
MENU
8.
SET
9.
SCAN
USB port
10. Power switch
11. LCD Display
12.
UP button
13. DOWN button
14.
15.
MENU
16.
SET
17.
SCAN
USB port
18.
19.
20.
21.
22.
23.
24.
25.
26.
27.
28.
Slot for front mount Antenna
Antenna B
Mic / Line level Switch
Unbalanced Out
Balanced Out.
DC IN jack
Antenna A.
Mic / Line Switchlevel
Unbalanced Out.
Balanced Out
AC IN jack ( for certain market only )
1211 1213 18
4 5
10
3
27
19 28
20 21 23
22 24 25 26
QR -20 00
Press until
thispageappears.
Press buttonfor2secondstoenterthe modeandthecursor
willflashononlyonespot.Usethe buttontoselectoneof
the8presetlevels. Aftermakingthechange,press buttonfor
about3secondswillsavethechanges.
Press until
thispageappears.
MENU
SET SET
UP/DOWN
SET
MENU
Press button for 2 seconds to enter the mode. Use the
button to select either or mode
indicates selected. After making the change, press
buttonforabout3secondswillsavethechange.
SET SET
UP/DOWN USER PRESET LEFT
ARROW SET
Press buttonfor2secondstoenterthe modeandthecursor
willflash.Usethe buttontoselectthedigitdesired. Thetwo
digitsatthetoprightcorner isChannel. Thereare40possiblechannels
tobeenteredbyuser. Afterselectedthechannel,makethe
correspondingchangetothefrequency. Aftermakingallthechanges,
press buttonforabout3secondswillsavethechangeinGroup25.
SET SET
UP/DOWN
SET
USEREDIT:01USEREDIT:01
SQUELCHLEVEL
-95dBm(2)
SQUELCHLEVEL
-95dBm(2)
USERMODE
PRESETMODE ö
USERMODE
PRESETMODE ö
TochangeSquelchlevel
TogotoUserMode
PressPowerONofreceiverfor2secondsandrelease,thefollowingpage
W
rolltonextpage
illappear.
After5secondsoneofthefollowingpageswillautomaticallyappear,
Depending
whichonewaslastselectedasmainpage.
PressMENU will
PressMENUwill
rolltonextpage
PressMENUwill
rolltonextpage
PressMENUwill
rolltonextpage
PressMENUwill
rolltonextpage
PressMENUwill
rolltonextpage
Remark: TransmitterisatOFFstatus.
Q5X
QR-2000
SQUELCHLEVEL
-95dBm(2)
CF:01-01
RF AF
USERMODEUSERMODE
3
Toviewandrollthevariousdisplaypages
USERNAME
RF AF
Q5X
QR-2000
801.100MHz
RF AF
CF:01-01
RF AF
USERNAME
RF AF
801.100MHz
RF AF
IfMENUisnotpressed
again,thispagewillstay
asmainpage.
IfMENUisnotpressed
again,thispagewillstay
asmainpage.
IfMENUisnotpressed
again,thispagewillstay
asmainpage.
IfMENUisnotpressed
again,itwillautomatically
returntooneofthe
3mainpages.
IfMENUisnotpressed
again,itwillautomatically
returntooneofthe
3mainpages.
IfMENUisnotpressed
again,itwillautomatically
returntooneofthe
3mainpages.
Press
Remark : Brand name and Model number are factory preset. It is NOT user-
changeable.
MENUuntil
thispageappears.
Press until
thispageappears.
MENU
Remark: TransmitterisON,then A orB,RF& AFlevelindicatorwilllightup.
Press buttonfor2secondstoenterthe modeandthecursorwill
flash.Press againeachtimewillmovethecursoroneposition.Usethe
buttontoselectthecharacterordigit.Press againwillmake
thechangeandmovethecursor onepositionforward. Afterfinishingallthe
changes,press buttonforabout3secondstosavethechanges.
SET SET
SET
UP/DOWN SET
SET
Press until
thispageappears.
Press buttonfor2secondstoenterthe modeandthefollowing
displaywillappearandthecursorwillflash.
MENU
SET SET
Press againeachtimewillmovethecursoroneposition. Thefirsttwo
topdigitsontheleftistheGroupandthesecondtoptwodigitstotheright
istheChannel. Therearealltogether25Groupsand40Channels(
25*40=1000)preset
frequenciestobechosen.Usethe buttontoselectthedigit.
PressSET againwillmakethechangeandmovethecursoroneposition
forward.OnceeithertheGrouportheChannelhasbeenaltered,the
frequencywillbechangedautomatically. Afterfinishingallthechanges,
press buttonforabout3secondswillsavethechanges.
SET
UP/DOWN
SET
4
Q5X
QR-2000
OperatingInstructions
A --USERNAME--B
RF---------- AF---------
Makingchangestothevariousdisplays.
TochangeUserName
AUSERNAMEBö ÷
A --801.100MHZ--B
RF---------- AF---------
CF:01-01
800.000MHz
TochangeFrequency
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4

Quantum5x QR-2000 Operating instructions

Brand
Quantum5x
Model
QR-2000
Type
Operating instructions
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Other documents