Z-Wave VRI10-1LZ Installation guide

Brand: Z-Wave

Model: VRI10-1LZ

Category: Dimmers

Type: Installation guide

Single Pole (One location) or 3-Way (Multi-location)

Scene Capable Incandescent Dimmer

Cat. No. VRI1

-1L, 1000W (Lighted)

120VAC, 60Hz

INSTALLATION INSTRUCTIONS

DI-000-VRI10-02A

WARNINGS AND CAUTIONS:

• Tobeinstalledand/orusedinaccordancewithappropriateelectricalcodesandregulations.

• Ifyouareunsureaboutanypartoftheseinstructions,consultaqualiedelectrician.

• Toavoidoverheatingandpossibledamagetothisdeviceandotherequipment,donotinstalltocontrolareceptacle,uorescentlighting,amotor-oratransformer-operatedappliance.

• Usewithincandescentor120Vhalogenxturesonly.

•

Vizia RF +

dimmersarenotcompatiblewithstandard3-wayor4-wayswitches.TheymustbeusedwithcompatibleVizia+™orViziaRF+

remotesformulti-locationdimming.

• Useonlyone(1)ViziaRF+™dimmerinamulti-locationcircuitwithupto9coordinatingremotes(withoutLEDs)orupto4matchingremotes(withLEDs).Theremote(s)willturnthe

lightonatthebrightnesslevelselectedatthedimmer.

WARNINGS AND CAUTIONS:

• Dimmermaynotoperatewithdiodedlamps(SylvaniaDesigner16™orPhilipsPAR-16™).

• Totalminimumloadmustexceed40W.

• Dimmermayfeelwarmtothetouchduringnormaloperation.

• Recommendedminimumwallboxdepthis2-1/2”.

• Maximumwirelengthfromdimmertoallinstalledremotescannotexceed300ft.

• Disconnectpoweratcircuitbreakerorfusewhenservicing,installingorremovingxture.

• Usethisdeviceonlywithcopperorcoppercladwire.WithaluminumwireuseonlydevicesmarkedCO/ALRorCU/AL.

INSTALLING YOUR DIMMER

NOTE: UsecheckboxeswhenStepsarecompleted.

√

YL/RD

Coordinating Remote

Dimmer

Black

Green

R ed

Yellow/Red

Hot (Black)

Neutral (White)

Load

Dimmer

Coordinating Remote (no LEDS)

YL/RD

Black

Do not use for

incandescent

applications.

White

Line

120VAC, 60Hz

Green

Ground

Green

Ground

Tools needed to install your Dimmer

Slotted/PhillipsScrewdriver ElectricalTape

Pliers   Pencil 

Cutters   Ruler

3-Way Wiring with Coordinating Remote

(no LEDs) Application:

Step 4b

Green

Ground

Hot (Black)

Neutral (White)

Load

Dimmer

Black

White

Line

120VAC, 60Hz

Black

Yellow/Red

Red

Insulating

Label

Single-Pole Wiring Application:

Step 4a

Black

Green

Red

Yellow/Red

Dimmer

Insulating Label:

This wire is used in

3-way installations

only. For single pole

installations, do

not remove this

insulating label.

IMPORTANT:

For3-Wayapplications,notethatoneofthescrewterminals

fromtheoldswitchbeingremovedwillusuallybeadifferentcolor(Black)

orlabeledCommon.Tagthatwirewithelectricaltapeandidentifyasthe

common(LineorLoad)inboththedimmerwallboxandremotewallbox.

Step 2

Identifying your wiring application

(most common):

NOTE:Ifthewiringinthewallboxdoesnotresemble

anyofthesecongurations,consultaqualied

electrician.

3-Way

1. Line or Load

(See important

instruction

below)

2. Neutral

3. Ground

4. FirstTraveler

– note color

5. SecondTraveler

– note color

Single-Pole

1. Line (Hot)

2. Neutral

3. Ground

4. Load

INTRODUCTION

Leviton’s

Vizia RF +

componentsaredesignedtocommunicate

witheachotherviaRadioFrequency(RF)toprovideremotecontrol

ofyourlighting.UsingRFtechnologyallowsLevitontoprovidethe

greatestsignalintegritypossible.EachmoduleinLeviton’s

Vizia

RF +

componentlineisaZ-Wave

enableddevice.InaZ-Wave

network,eachdeviceisdesignedtoactasarouter.Theserouters

willre-transmittheRFsignalfromonedevicetoanotheruntilthe

intendeddeviceisreached.Thisensuresthatthesignalisreceived

byitsintendeddevicebyroutingthesignalaroundobstaclesand

radiodeadspots.TheSceneCapableIncandescentDimmeris

compatiblewithanyZ-Wave

enablednetwork,regardlessofthe

manufacturerandcanalsobeusedwithotherdevicesdisplaying

theZ-Wave

logo.

CAUTION:

RemembertoexercisegoodcommonsensewhenusingtheTimer

featuresofyourremote,especiallywhenschedulingunattended

devices.Therecanbesomeunexpectedconsequencesifnot

usedwithcare.Forexample,anemptycoffeepotcanberemotely

turnedon.Ifthatshouldhappen,yourcoffeepotcouldbedamaged

fromoverheating.Ifanelectricheateristurnedonbyremote

controlwhileclothingisdrapedoverit,arecouldresult.DO NOT

USEtheremoteforthecontrolofhighpowerheatingappliances

suchasportableheaters.Thisdevicewillnotcontrollightingthatis

usedwithelectroniclow-voltageandhighfrequencypowersupply

transformers,norhighpressuredischargelamps(HIDlighting).

Thisincludesmercury-vapor,sodiumvaporandmetalhalidelamps.

• SoftfadeON/OFF

• Scenecapable

• Twowaycommunication

• RFreliability

• NoNeutralwirerequired

FEATURES

• ON/OFFLEDandBrightness

levelLED

• Easeofinstallation–Nonew

wiring

• CompatiblewithotherZ-Wave

enableddevices

Changing the color of your Dimmer:

Yourdevicemayincludecoloroptions.Tochangecolorofthe

face,proceedasfollows:

Line up tabs

and press in

sides one at a

time to attach

Push in

side at tab

to release

Installing Dimmer by itself or with other devices

IfinstallingDimmerinasingledeviceapplication,proceedwiththe

INSTALLING YOUR DIMMERsection.IfinstallingDimmerinamulti-

deviceapplication,proceedasfollows:

MULTI-DEVICE APPLICATION:

Inmulti-dimmerinstallations,thereductionofthedimmer’scapacityis

required.Refertothechartformaximumloadperdimmer.

MAXIMUM LOAD PER DIMMER FOR MULTI-DEVICE

Cat. No.

VRI1

1000W

Single

800W

Two Devices

650W

More than 2 Devices

Hot (Black)

Neutral (White)

Load

Dimmer

Matching Dimmer

Remote (with LEDs)

YL/RD

Red

Black

White

Yellow/

Red

Line

120VAC, 60Hz

Green

Ground

Green

Ground

Additional

Neutral Wire

YL/RD

Matching Dimmer Remote

Dimmer

Black

Green

Re d

Yellow/Red

Step 4c

3-Way Wiring with Matching Remote

(w/LEDs) Application:

Strip Gage

(measure bare wire

here or use gage on

back of the dimmer)

5/8”

(1.6 cm)

cut

(if necessary)

Step 3

Preparing and connecting wires:

• Makesurethattheendsofthewiresfromthewall

boxarestraight (cut if necessary).

• Removeinsulationfromeachwireinthewallboxasshown.

• For Single Pole Application, go to Step 4a.

• For 3-Way Coordinating Remote (no LEDs) Application, go to Step 4b.

• For 3-Way Matching Remote (with LEDs) Application, go to Step 4c.

NOTE: ThedimmermustbeinstalledinawallboxthathasaLoad

connection.Thematchingremotemustbeinstalledinawallboxwith

aLineHotconnectionandaNeutralconnection.ANeutralwiretothe

matchingremoteneedstobeaddedasshown.

Ifyouareunsureaboutanypartoftheseinstructions,consulta

qualiedelectrician.

NOTE:Maximumwirelengthfromdimmertoallinstalledremotes

cannotexceed300ft.

WIRING MATCHING REMOTE (wall box with Line Hot

connection):

Connect wires per WIRING DIAGRAM as follows:

• GreenorbarecopperwireinwallboxtoGreenterminalscrew.

• LineHot(common)wallboxwireidentied(tagged)whenremoving

oldswitchandFirstTravelertoremoteterminalscrewmarked“BK”.

• SecondTravelerwallboxwirefromdimmertoremoteterminal

screwmarked“YL/RD”(note wire color).Thistravelerfromthe

remotemustgototheterminalscrewonthedimmer

marked“YL/RD”.

• LineNeutralwallboxtoremoteterminalscrewmarked“WH”.

WIRING DIMMER (wall box with Load connection):

Connect wires per WIRING DIAGRAM as follows:

• GreenorbarecopperwireinwallboxtoGreendimmerlead.

• Loadwallboxwireidentied(tagged)whenremovingoldswitchto

Reddimmerlead.

• FirstTravelerLineHottoBlackdimmerlead.

• RemoveRedinsulatinglabelfromYellow/Reddimmerlead.

• SecondTravelerwallboxwire(note color as above)toYellow/Red

dimmerlead.Thistravelerfromthedimmermustgototheterminal

screwontheremotemarked“YL/RD”.

• ProceedtoStep5.

Step 1

WARNING: TO AVOID FIRE, SHOCK, OR DEATH;

TURN OFF POWER

atcircuitbreakeror

fuseandtest

thatpowerisoff

beforewiring!

/./&&

/./&&/./&&

/./&&

Remove all

inner side

sections

Do not

remove

outer side

sections

WIRE NUT / # OF CONDUCTOR COMBINATION CHART

1-#12w/1to3#14,#16or#18

2-#12w/1or2#16or#18

1-#14w/1to4#16or#18

2-#14w/1to3#16or#18

For non-standard wiring applications, refer

to Wire Nut and Conductor Size Chart

WIRING DIMMER:

Connect wires per WIRING DIAGRAM as follows:

• GreenorbarecopperwireinwallboxtoGreendimmerlead.

• LineHotwallboxwiretoBlackdimmerlead.

• LoadwallboxwiretoReddimmerlead.

• Yellow/ReddimmerleadshouldhaveRedinsulationlabelafxed.

NOTE:IfinsulatinglabelisnotafxedtoYellow/Reddimmerlead,

useelectricaltapetocover.

• Proceed to Step 5.

WIRING DIMMER:

Connect wires per WIRING DIAGRAM as follows:

NOTE:WhenusingthecoordinatingremotewithoutLEDs,thedimmercanbe

installedoneithertheLineorLoadsideofthe3-waycircuit.

NOTE: Maximumwirelengthfromdimmertoallinstalledremotescannot

exceed300ft.

• GreenorbarecopperwireinwallboxtoGreendimmerlead.

• LineHot(common)wallboxwireidentied(tagged)whenremovingoldswitch

toBlackdimmerlead.

• FirstTravelerwallboxwiretoReddimmerlead(note wire color).Thistraveler

fromthedimmermustgototheterminalscrewontheremotemarked“RD”.

• RemoveRedinsulatinglabelfromYellow/Reddimmerlead.

• SecondTravelerwallboxwiretoYellow/Reddimmerlead(note wire color).

Thistravelerfromthedimmermustgototheterminalscrewontheremote

marked“YL/RD”.

WIRING COORDINATING REMOTE:

Connect wires per WIRING DIAGRAM as follows:

NOTE: Maximumwirelengthfromdimmertolastremoteis300ft.

• GreenorbarecopperwireinwallboxtoGreenterminalscrew.

• Loadwallboxwireidentied(tagged)whenremovingoldswitchtoterminal

screwmarked“BK”.

• FirstTravelerwallboxwire(note color as above)toterminalscrewmarked

“RD”.ThistravelerfromtheremotemustgototheReddimmerlead.

• SecondTravelerwallboxwire(note color as above)toterminalscrew

marked“YL/RD”.ThistravelerfromtheremotemustgototheYellow/Red

dimmerlead.

• Remoteterminalscrewmarked“WH”shouldhaveWhiteinsulationlabel

afxed.NOTE: Ifinsulatinglabelisnotafxedtoterminalscrewmarked“WH”,

useelectricaltapetocover.

• ProceedtoStep5.

Including Scene Capable Dimmer into

Z-Wave

Network:

Restore Power: Restorepoweratcircuitbreakeror 

fuse.Installation is complete.

D)ThePrimaryProgrammer/ControllerwillassignanodeIDnumber

(Name)forthismodule.

NOTE: ThisIDnumber(Name)willbestoredinthecontrollerlibrary

tobeusedforfuturereference.

NOTE: Youmayeditthename

ofthisdeviceatthistime.

E) The dimmer is now installed in

the network.

NOTE: Ifadimmerhasbeen

successfullyIncludedinthenetwork

andtheusertriestoIncludeitagain

withoutrstexcludingitfromthe

network,themodulewillretainthe

rstnodeIDithadreceivedand

ignorethesecond.

Testing your Dimmer prior to mounting in

wall box:

LIMITED 5 YEAR WARRANTY AND EXCLUSIONS

LevitonwarrantstotheoriginalconsumerpurchaserandnotforthebenetofanyoneelsethatthisproductatthetimeofitssalebyLevitonisfreeofdefectsinmaterialsandworkmanshipundernormalandproperuseforveyearsfromthepurchasedate.Leviton’sonlyobligationistocorrectsuchdefectsbyrepairorreplacement,atitsoption,ifwithinsuchveyearperiodtheproductisreturnedprepaid,withproofof

purchasedate,andadescriptionoftheproblemtoLeviton Manufacturing Co., Inc., Att: Quality Assurance Department, 59-25 Little Neck Parkway, Little Neck, New York 11362-2591.Thiswarrantyexcludesandthereisdisclaimedliabilityforlaborforremovalofthisproductorreinstallation.Thiswarrantyisvoidifthisproductisinstalledimproperlyorinanimproperenvironment,overloaded,misused,opened,

abused,oralteredinanymanner,orisnotusedundernormaloperatingconditionsornotinaccordancewithanylabelsorinstructions.There are no other or implied warranties of any kind, including merchantability and ﬁtness for a particular purpose,butifanyimpliedwarrantyisrequiredbytheapplicablejurisdiction,thedurationofanysuchimpliedwarranty,includingmerchantabilityandtnessforaparticular

purpose,islimitedtoveyears.Leviton is not liable for incidental, indirect, special, or consequential damages, including without limitation, damage to, or loss of use of, any equipment, lost sales or proﬁts or delay or failure to perform this warranty obligation.Theremediesprovidedhereinaretheexclusiveremediesunderthiswarranty,whetherbasedoncontract,tortorotherwise.

• Restorepoweratcircuitbreakerorfuse.

• PresspaduntillocatorlightisOFF.Lights

shouldturnON.IflightsdonotturnON,

presstherighthalfofDIM/BRIGHTbaruntil

thelightsbrighten.

If lights still do not turn ON, refer to the

TROUBLESHOOTING section.

NOTES:

• Ifusinganon-LevitonProgrammer/Controller,

refertotheProgrammer/Controllerinstruction

sheetforIncludingadevice.

• IfusingtheVRCPG'sInstallChecklistfeature,

godirectlytoStepB.

A)IfusingaLevitonZ-Wave

Programmer/

Controller,Cat.No.VRCPG,presstheMenu

buttonandscrolldowntoSystemSetup.

PressthecenterbuttontoselectSystem

SetupMenu.ChooseAdvancedSettings.

PressthecenterbuttontoselectNetwork.

B)Whilestandingclosetothemodule(approx.

2-5ft),pressthecenterbuttonto<Include>

deviceinthenetwork.

NOTE:Onlyonedevicemaybeincludedatatime.DO NOTput

multipledevicesintotheInclusionmodeatanytime.

C) WhiletheProgrammer/ControllerisintheInclusionmodeandthe

LocatorLEDisONonthedimmer,pushthepushpadtoturnON

thedimmer.TheProgrammer/Controllerwillverifyinclusionand

thelocatorLEDwillturnOFFonthedimmer.

 IfthedimmerisashingAmberwhileintheInclusionmode,the

Programmer/Controllerisstilltryingtocommunicatewiththe

dimmer.Waituntilthedevicestopsashing,thenpresspushpad.

NOTE:IfthelocatorLEDonthedimmerturnssolidRedwhile

including,therehasbeenacommunicationerror.Referto

Troubleshootingsection.

DI-000-VRI10-02A2008©LevitonMfg.Co.,Inc.

ProtectedunderU.S.PatentNumber6,388,399andpatentspending

andlicensedunderU.S.PatentsNumbers5,905,442,and5,982,103

Programmer/Controller

Cat. No. VRCPG

Button

OFF

Center

Button

• Lights Flickering

 - Lamphasabadconnection.

 - Wiresnotsecuredrmlyunderterminalscrewsofdimmer

and/orremote.

 - Localswitch,ON

• Light does not turn ON and Locator LED does not turn ON

 - Circuitbreakerorfusehastripped.

 - Lampisburnedout.

 - LampNeutralconnectionisnotwired.

 - Conrmthatthedeviceisbeingsuppliedfroma120V,60HzAC

sourceONLY.

 - Conrmthatunitisprogrammedproperly.Repeat“TOINSTALL”

sectiontoverifythatithasbeenincludedintheZ-Wave™

network.

• Intermittent dimmer operation

- Minimumloadisunder40W.

 - ConrmthattheLoadbeingcontrolleddoesnotexceedthe

1000Wdimmerlimit.

• Remote does not operate lights

- Ensurethattotalwirelengthdoesnotexceed300ft.

TROUBLESHOOTING

For additional information, contact Leviton’s Techline

at 1-800-824-3005 or visit Leviton’s website at

www.ViziaRFplus.com

NOTE:Thelocatorlightwillilluminatewhen

theloadisintheOFFpositiontofacilitate

accessinthedark.

NOTE:Ifusingthedimmerina3-way

application,thelightswillturnONat

brightnesssetondimmer’sDIM/BRIGHTbar.

Thelightingcanbecontrolledfromeitherthe

dimmerortheremotelocation.

Push Pad (Default settings)

Turn ON from OFF position:

Tap–LightsturnONtopresetlevel.

PressandHold–LightsturnONtofullbright.

Turn OFF from ON position:

Tap–LightsturnOFF.

LED Brightness

Display

DIM/BRIGHT

Bar

Push

Pad

Locator

Light

OPERATION

Installationmaynowbecompleted

bytighteningmountingscrewsinto

wallbox.Attachwallplate.

Dimmer Mounting:

TURN OFF POWER AT

CIRCUIT BREAKER

OR FUSE.

Step 7

Step 6

NOTE: ItisveryimportanttoaccuratelyExcludedevicesfromthe

networkwhenmovingorremovingadevicefromaZ-Wave

network.

ThisensuresthatallinformationhasbeenremovedfromyourPrimary

Programmer/Controller’sinformationtableandisnotcountedontobea

partofthemeshnetwork.

A)IfusingaLevitonZ-Wave

Programmer/Controller,Cat.No.VRCPG,

presstheMenubuttonandscrolldowntoSystemSetup.Press

thecenterbuttontoselectSystemSetupMenu.ChooseAdvanced

Settings.PressthecenterbuttontoselectNetwork.

B) Whilestandingclosetothedimmer,pressthecenterbuttonto

<Exclude>devicefromthenetwork.WhiletheProgrammer/Controller

isintheExclusionmodeandthelocatorLEDisONonthedimmer,

pressthepushpadonthedimmer.TheProgrammer/Controllerwill

verifyExclusionandthelocatorLEDwillturnOFFonthedimmer.

 IfthedimmerisashingAmberwhileintheExlusionmode,the

Programmer/Controllerisstilltryingtocommunicatewiththedimmer.

Waituntilthedevicestopsashing,thenpressthepushpad.

Factory Default:

Ifyourdimmerisnotresponding,oryouareunabletocontrolitafter

youhavetriedtoInclude/Excludeitmultipletimes,itmaybenecessary

toresetthedimmertoitsoriginalfactorysettings.Toaccomplishthis,

proceedasfollows:

• Onthedimmer,engageheair-gapswitch(refer to Operation

section)andwait5seconds.Presspushpadbackintoframeand

holdpushpaduntilthelocatorLEDturnsAmberandthenturns

Red.Thedimmerisnowreset.Oncethedimmerisreset,itwillbe

necessarytoRe-Includeittoanetworkbeforeitcanbeused.

CAUTION:SETTINGADEVICETOAFACTORYDEFAULTDOES

NOTEXCLUDETHATDEVICEFROMANETWORK.THEEXCLUSION

PROCEDUREMUSTSTILLBEFOLLOWEDTOREMOVETHEDEVICE

FROMTHEPRIMARYCONTROLLER’SINFORMATIONTABLE.

FAILURETODOSOMAYRESULTINASYSTEMTHATISSLOWTO

RESPOND,ORMAYFAILTORESPONDTOSOMEDEVICES.

Step 9

Excluding Dimmer from Network:

Step 8

NOTE: Dresswireswithabend

asshownindiagraminorderto

relievestresswhenmounting

device.

• Positionallwirestoprovideroominoutlet

wallboxfordevice.

• Ensurethattheword“TOP”isfacingup

ondevicestrap.

• Partiallyscrewinmountingscrewsinwall

boxmountingholes.

Step 5

A-2) TheLocatorLEDwillblink2timespersecondtoindicatethe

deviceisinProgramModeA-2, Minimum Brightness Level.

TochangetheMinimum Brightness Levelfrom1-50%,use

theDIM/BRIGHTBar.Thelightoutputwillreecttheminimum

brightnesslevelselected.BytappingthePushPadthissettingwill

automaticallybesavedandthedevicewilladvancetothenext

programmingmode,A-3.

A-3) TheLocatorLEDwillblink3timespersecondtoindicateProgram

Mode A-3, Preset ON Level.TochangethecurrentPreset ON

Levelfrom1-100%,usetheDIM/BRIGHTBar.Ifthisfeatureis

notdesired,pressandholdthelefthalfoftheDIM/BRIGHTBar

(

)

untilnoLEDislit(defaultsetting).BytappingthePushPad

thissettingwillautomaticallybesavedandthedevicewill

exit

ProgrammingModeA.

Program Mode B

To enter Program Mode B:

PressandholdthePushPadandthenthelefthalfofthe

DIM/BRIGHTBar(

)for5secondsuntiltheLocatorLEDandrightmost

LED(LED7)begintoblink.

B-1) UponreleasingthePushPadandthelefthalfofthe

DIM/BRIGHTBar(

),theLocatorLEDwillcontinuetoblinkonce

persecondindicatinghedimmerisinProgramModeB-1, ON

Fade Rate.TochangetheON Fade Rate,usetheDIM/BRIGHT

BartomovetheLEDtothedesiredpresetlevelaccordingtoChart

B.BytappingthePushPadthissettingwillautomaticallybesaved

andthedevicewilladvancetothenextprogrammingmode,B-2.

B-2) TheLocatorLEDwillblink2timespersecondtoindicateProgram

Mode B-2, OFF Fade Rate.TochangetheOFF Fade Rate,use

theDIM/BRIGHTBartomovetheLEDtothedesiredpresetlevel

according to Chart B.BytappingthePushPadthissettingwill

automaticallybesavedandthedevicewilladvancetothenext

programmingmode,B-3.

LED Brightness

Display

1 2 3 4 5 6 7

Deﬁnition of A Modes

A-1) EnergySave:Setsthemaximumbrightnesslevelforenergy

savings.

A-2) MinimumBrightnessLevel:Setstheminimumdimminglevel.

A-3) PresetONLevel:Setstheturnonbrightnesslevelregardlessof

theprevioussetlightlevel(formerlyDimLock).

Deﬁnition of B Modes

B-1) ONFadeRate:Setstheamountoftimeinsecondsittakesthe

lightstoturnONtomaximumbrightness.

B-2) OFFFadeRate:Setstheamountoftimeinsecondsittakesthe

lightstoturnOFFfrommaximumbrightness.

B-3) LEDOptions:SetsthetimeperiodinsecondstheLocatorLED

andBrightnessdisplaywillstayonbeforeextinguishing.

Deﬁnition of LEDs

LeftmostLED=LED1

RightmostLED=LED7

NOTES:

• Thedevicewillexitprogramming

modeafter3minutesofinactivity.

• Pressingthepushpadatanytime

duringprogrammingwilladvancethe

devicetothenextprogrammingmode.

ADVANCED PROGRAMMING FEATURES

Program Mode A

To enter Program Mode A:

PressandholdthePushPadandthentherighthalfofthe

DIM/BRIGHTBar

(

)

for5secondsuntiltheLocatorLEDand

leftmostLED(LED1)begintoblink.

A-1) UponreleasingthePushPadandtherighthalfofthe

DIM/BRIGHTBar

(

)

,theLocatorLEDwillcontinuetoblink

oncepersecondandtherightmostLEDwillilluminateto

displaythedeviceisinProgramModeA-1, Energy Save.The

defaultenergysavemodeis100%i.e.fullbright.Tochange

the Energy Savelevel,usetheDIM/BRIGHTBartomove

thecorrespondingLEDtothedesireddiscretepresetlevel

according to Chart A.BytappingthePushPadthissettingwill

automaticallybesavedandthedevicewilladvancetothenext

programmingmode,A-2.

B-3)

TheLocatorLEDwillblink3timespersecondtoindicateProgram

Mode B-3, LED Options.TochangetheLED Optionssettings,

usetheDIM/BRIGHTBartomovetheLEDtothedesiredpreset

settingaccordingtotheChart B-3.BytappingthePushPad

thissettingwillautomaticallybesavedandthedevicewillexit

Programming

ModeB.

LED

LED 1

LED 2 (Default)

LED 3

LED 4

LED 5

LED 6

LED 7

FADE ON

0 seconds (instant)

0.5 seconds

1.5 seconds

3.0 seconds

6.0 seconds

10 seconds

25 seconds

0 seconds (instant)

0.5 seconds

1.5 seconds

3.0 seconds

6.0 seconds

10 seconds

25 seconds

FADE OFF

Chart B

When indicator

light is at LED #

Light output is at

100%

97%

95%

90%

85%

80%

75%

Energy consumption

savings amounts to

11%

14%

17%

20%

Chart A

Chart B-3

LED

LED 1

LED 2

LED 3

LED 4

LED 5

LED 6

LED 7

LOCATOR LED TIMEOUT

Active

Turns off 5 sec. after use

LED BRIGHTNESS DISPLAY OPTIONS

Active

Turns off 5 sec. after use

Active

Turns off 5 sec. after use

LED Bar active

LED Bar turns off 5 sec. after use

VRCPG

Programmer/

Controller

NOTE: Remotemustbeinclose

proximitytodimmerwhenincluding

innetwork.

DIM/BRIGHT Bar

BRIGHTEN:

PressrighthalfofDIM/BRIGHTBar–Lightsbrightentodesiredlevel.

DIM:

PresslefthalfofDIM/BRIGHTBar–Lightsdimtodesiredlevel.

IfyoucontinuetoholdthelowerhalfoftheDIM/BRIGHTBar,thelights

willDIMtominimumlevelandthenturnOFF.

NOTE:WhenlightsareOFFyoucanchangethe

lightlevelthatthelightswillturnONtousingthe

DIM/BRIGHTBar.

Ifthereisapoweroutage,whenthepoweris

restoredthelightswillreturntothelastsetting

beforethepowerinterruption.

Air-Gap Switch:Onthedimmeronly,engage

theair-gapswitchbygentlypressingthe

topofthepushpaduntilthebottomlifts

completelyoutoftheframeandaclickis

heard (refer to Figure).LEDswillturnOFF.

Thiswillcutpowertothexturetoreplace

thebulb.Afterservicingiscomplete,pushthe

pushpadbackfornormaloperation.

Cleaning: Cleanwithadampcloth.DO NOT

usechemicalcleaners.

Gently press top

of push pad

Thisequipmenthasbeentestedandfoundtocomplywiththelimits

foraClassBDigitalDevice,pursuanttoPart15oftheFCCRules.

Theselimitsaredesignedtoprovidereasonableprotectionagainst

harmfulinterferenceinaresidentialinstallation.Thisequipment

generates,uses,andcanradiateradiofrequencyenergyand,ifnot

installedandusedinaccordancewiththeinstructions,maycause

harmfulinterferencetoradiocommunications.However,thereisno

guaranteethatinterferencewillnotoccurinaparticularinstallation.If

thisequipmentdoescauseharmfulinterferencetoradioortelevision

reception,whichcanbedeterminedbyturningtheequipmentOFF

andON,theuserisencouragedtotrytocorrecttheinterferenceby

oneormoreofthefollowingmeasures:

• ReorientorrelocatethereceivingAntenna.

• Increasetheseparationbetweentheequipmentandthe

receiver.

• Connecttheequipmentintoanoutletonacircuitdifferentfrom

thattowhichthereceiverisconnected.

• Consultthedealeroranexperiencedradio/tvtechnicianfor

help.

FCC COMPLIANCE STATEMENT

Z-Wave VRI10-1LZ Installation guide

Brand: Z-Wave

Model: VRI10-1LZ

Category: Dimmers

Type: Installation guide

Download PDF

report

Z-Wave VRI10-1LZ Installation guide

Z-Wave VRI10-1LZ Installation guide

Related papers

Other documents