Z-Wave VRF01-1LZ Operating instructions

Brand: Z-Wave

Model: VRF01-1LZ

Type: Operating instructions

This manual is also suitable for

031-VRF01-1LZ

Single Pole (One location) or 3-Way (Multi-location)

Quiet Fan Speed Control

Cat. No. VRF

1-1L, 1.5A

120VAC, 60Hz

INSTALLATION INSTRUCTIONS

WARNINGS AND CAUTIONS:

• Tobeinstalledand/orusedinaccordancewithappropriateelectricalcodesandregulations.

• Ifyouareunsureaboutanypartoftheseinstructions,consultaqualiedelectrician.

• Toavoidoverheatingandpossibledamagetothisdeviceandotherequipment,donotinstalltocontrolareceptacle,uorescentlighting,amotorora

transformer-operatedapplianceotherthanappropriateceilingfans.

• Toreduceriskofreorelectricalshock,thiscontrolistobeusedwithceilingfansthatarerated120VAC,totalload1.5amperesmaximum.

• Foruseonceilingpaddlefanswithsplit-capacitororshadedpolemotorsonly.Pleaserefertomanufacturer’sinstructionsorratinglabelonthemotorto

conrmtype.Usewithanyothertypesofmotorsorequipmentmaycauseoverheatingand/ordamagetothemotorsorequipment.

WARNINGS AND CAUTIONS:

• ViziaRF+™fanspeedcontrolsarenotcompatiblewithstandard3-wayor4-wayswitches.

TheymustbeusedwithcompatibleVizia+

orViziaRF+™remotesformulti-locationcontrol.

• Useonlyone(1)ViziaRF+™fanspeedcontrolinamulti-locationcircuitwithupto9coordinatingremotes(withoutLEDs)

orupto4matchingremotes(withLEDs).Theremote(s)willturnthefanonatthespeedselectedatthecontrol.

• Recommendedminimumwallboxdepthis2-1/2".

• Maximumwirelengthfromdimmertoallinstalledremotescannotexceed300ft(90m).

• Disconnectpoweratcircuitbreakerorfusewhenservicing,installingorremovingxture.

• Usethisdeviceonlywithcopperorcoppercladwire.WithaluminumwireuseonlydevicesmarkedCO/ALRorCU/AL.

DI-000-VRF01-02A-X3

For non-standard wiring applications, refer

to Wire Nut and Connector Size Chart

1-#12w/1to3#14,#16or#18

2-#12w/1or2#16or#18

1-#14w/1to4#16or#18

2-#14w/1to3#16or#18

WIRE CONNECTOR / # OF COND. COMBINATION CHART

• ForSingle-PoleApplication,gotoStep4a.

• For3-WayCoordinatingRemote(noLEDs)Application,gotoStep4b.

• For3-WayMatchingRemote(withLEDs)Application,gotoStep4c.

Fan Speed Control

Fan

Hot (Black)

Neutral (White)

Bla c k

White

Red

Green

Ground

Line

120 V A C , 60H z

Insulating

Label

Y e llow/

Red

WIRINGFANSPEEDCONTROL:

ConnectwiresperWIRINGDIAGRAMasfollows:

• GreenorbarecopperwireinwallboxtoGreenlead.

• LineHotwallboxwiretoBlacklead.

• LoadwallboxwiretoRedlead.

• LineNeutralwallboxwiretoWhitelead.

• Yellow/RedwireshouldhaveRedinsulationlabelafxed.

NOTE:IfinsulatinglabelisnotafxedtoYellow/Redlead,use

electricaltapetocover.

• ProceedtoStep5.

Hot (Bla c k )

Neutral (White)

Fan Speed Control Coo r dinating Remote (no LEDs )

YL/RD

Bla c k

BK WH

White

White Black

Yellow/Red Red

Fan

Line

120 V A C , 60H z

Green

G r oun d

Green

G r oun d

(u n used )

Slotted/PhillipsScrewdriver ElectricalTape Pliers 

Pencil   Cutters  Ruler

ToolsneededtoinstallyourFanSpeedControl

Changingthecolorofyourdevice:

Yourdevicemayincludecoloroptions.Tochangecoloroftheface,

proceedasfollows:

Pushinsideat

tabtorelease

Lineuptabsand

press in sides one

atatimetoattach

MULTI-DEVICEAPPLICATION

Inmulti-fanspeedcontrolinstallations,there

isnoderatingnecessary.Refertothechartfor

maximumloadperfanspeedcontrol.

Ifinstallingfanspeedcontrolinasingledevice

application,proceedwiththeINSTALLING

YOURFANSPEEDCONTROLsection.If

installingfanspeedcontrolinamulti-device

application,proceedasfollows:

InstallingFanControlbyitselforwithotherdevices

Black

Red

Yellow/Red

Green

White

InsulatingLabel:

Thiswireisusedin3-way

installationsonly. For single

pole installations, do not

removethisinsulatinglabel.

SinglePoleWiringApplication:

Step4a

YL/RD

Coo r dinating Remot e

Fan Speed Control

Black

R ed

Yellow/Red

Green

White

3-WayWiringwithCoordinatingRemote

(noLEDs)Application:

Step4b

INTRODUCTION

Leviton’s

ViziaRF+

componentsaredesignedtocommunicatewitheachothervia

RadioFrequency(RF)toprovideremotecontrolofyourlighting.UsingRFtechnology

allowsLevitontoprovidethegreatestsignalintegritypossible.Eachmodulein

Leviton’s

ViziaRF+

componentlineisaZ-Wave

enableddevice.InaZ-Wave

network,eachdeviceisdesignedtoactasarouter.Theserouterswillre-transmit

theRFsignalfromonedevicetoanotheruntiltheintendeddeviceisreached.This

ensuresthatthesignalisreceivedbyitsintendeddevicebyroutingthesignalaround

obstaclesandradiodeadspots.TheSceneCapableQuietFanSpeedControlis

compatiblewithanyZ-Wave

enablednetwork,regardlessofthemanufacturerand

canalsobeusedwithotherdevicesdisplayingtheZ-Wave

logo.

CAUTION:RemembertoexercisegoodcommonsensewhenusingtheTimer

featuresofyourremote,especiallywhenschedulingunattendeddevices.Therecan

besomeunexpectedconsequencesifnotusedwithcare.Forexample,anempty

coffeepotcanberemotelyturnedon.Ifthatshouldhappen,yourcoffeepotcould

bedamagedfromoverheating.Ifanelectricheateristurnedonbyremotecontrol

whileclothingisdrapedoverit,arecouldresult.DO NOT USEtheremoteforthe

controlofhighpowerheatingappliancessuchasportableheaters.Thisdevicewill

notcontrollightingthatisusedwithelectroniclow-voltageandhighfrequencypower

supplytransformers,norhighpressuredischargelamps(HIDlighting).Thisincludes

mercury-vapor,sodiumvaporandmetalhalidelamps.

IMPORTANT :For3-Wayapplications,notethatoneofthescrew

terminalsfromtheoldswitchbeingremovedwillusuallybeadifferent

color(Black)orlabeledCommon.Tagthatwirewithelectricaltapeand

identifyasthecommon(LineorLoad)inboththefanspeedcontrolwall

boxandremotewallbox.

MAXIMUMLOADPERFANSPEEDCONTROLFORMULTI-DEVICEAPPLICATION

Morethan2Devices

1.5A

TwoDevices

1.5A

Single

1.5A

Cat. No.

VRF

/./&&

/./&&/./&&

/./&&

Preparingandconnectingwires:

Pulloffpre-cutinsulationfromfanspeedcontrolleads.Make

surethattheendsofthewiresfromthewallboxarestraight

(cutifnecessary).Removeinsulationfromeachwireinthe

wallboxasshown:

INSTALLINGYOURFANSPEEDCONTROL

NOTE:UsecheckboxeswhenStepsarecompleted.

WARNING:TO

AVOID FIRE SHOCK

OR DEATH; TURN

OFFPOWERat circuit

breakerorfuseand

testthatpowerisoff

beforewiring!

Step 1

Identifyingyourwiringapplication

(mostcommon):

NOTE:Ifthewiringinyourwallboxdoesnotresembleanyof

thesecongurations,consultaqualiedelectrician.

Step 2

Step3

3-Way

1. LineorLoad

 (Seeimportant

instruction

 below)

2. Neutral

3. Ground

4. FirstTraveler

– note color

5. SecondTraveler

– note color

Single-Pole

1. Line (Hot)

2. Neutral

3. Ground

4. Load

Strip Gage

(measurebarewire

here or use gage on

backofthedimmer)

5/8”

(1.6cm)

cut

(ifnecessary)

•

ThisisaZ-Wave

controller

• Scenecapable

• Twowaycommunication

• RFreliability

• ON/OFFLEDandFanSpeedlevelLED

• Easeofinstallation–Nonewwiring

• CompatiblewithotherZ-Wave

enabled

devices

FEATURES

WIRINGFANSPEEDCONTROL:

ConnectwiresperWIRINGDIAGRAMasfollows:

NOTE:WhenusingthecoordinatingremotewithoutLEDs,thefanspeed

controlcanbeinstalledoneithertheLineorLoadsideofthe3-waycircuit.

NOTE:Maximumwirelengthfromfanspeedcontroltoallinstalledremotes

cannotexceed300ft(90m).

• GreenorbarecopperwireinwallboxtoGreenlead.

• LineHot(common)wallboxwireidentied(tagged)whenremovingold

switchtoBlacklead.

• FirstTravelerwallboxwiretoRedlead(notewirecolor).

• RemoveRedinsulatinglabelfromYellow/Redlead.

• SecondTravelerwallboxwiretoYellow/Redlead(notewirecolor).This

travelerfromthefanspeedcontrolmustgototheterminalscrewonthe

remotemarked"YL/RD".

• LineNeutralwallboxwiretoWhitelead.

WIRINGCOORDINATINGREMOTE:

ConnectwiresperWIRINGDIAGRAMasfollows:

NOTE:"BK"and"RD"terminalsoncoordinatingremoteareunused.Tightenboth

screws.

NOTE:

Maximumwirelengthfromfanspeedcontroltolastremoteis300ft(90m).

• GreenorbarecopperwireinwallboxtoGreenterminalscrew.

• Loadwallboxwireidentied(tagged)whenremovingoldswitchtoFirst

Traveler(notecolorasabove).

• SecondTravelerwallboxwire(notecolorasabove)toterminalscrewmarked

"YL/RD".ThistravelerfromtheremotemustgototheYellow/Redfanspeed

controllead.

• RemoveWhiteinsulatinglabelfromterminalscrewmarked"WH".

• LineNeutralwallboxwiretoterminalscrewmarked"WH".

• ProceedtoStep5.

LIMITED5YEARWARRANTYANDEXCLUSIONS

LevitonwarrantstotheoriginalconsumerpurchaserandnotforthebenetofanyoneelsethatthisproductatthetimeofitssalebyLevitonisfreeofdefectsinmaterialsandworkmanshipundernormalandproperuseforveyearsfromthepurchasedate.Leviton’sonlyobligationistocorrectsuchdefectsbyrepairorreplacement,atitsoption,ifwithinsuchveyearperiodtheproductisreturnedprepaid,withproof

ofpurchasedate,andadescriptionoftheproblemtoLevitonManufacturingCo.,Inc.,Att:QualityAssuranceDepartment,59-25LittleNeckParkway,LittleNeck,NewYork11362-2591.Thiswarrantyexcludesandthereisdisclaimedliabilityforlaborforremovalofthisproductorreinstallation.Thiswarrantyisvoidifthisproductisinstalledimproperlyorinanimproperenvironment,overloaded,misused,

opened,abused,oralteredinanymanner,orisnotusedundernormaloperatingconditionsornotinaccordancewithanylabelsorinstructions.Therearenootherorimpliedwarrantiesofanykind,includingmerchantabilityandtnessforaparticularpurpose,butifanyimpliedwarrantyisrequiredbytheapplicablejurisdiction,thedurationofanysuchimpliedwarranty,includingmerchantabilityandtness

foraparticularpurpose,islimitedtoveyears.Levitonisnotliableforincidental,indirect,special,orconsequentialdamages,includingwithoutlimitation,damageto,orlossofuseof,anyequipment,lostsalesorprotsordelayorfailuretoperformthiswarrantyobligation.Theremediesprovidedhereinaretheexclusiveremediesunderthiswarranty,whetherbasedoncontract,tortorotherwise.

DI-000-VRF01-02A-X3

WIRINGFANSPEEDCONTROL

(wallboxwithLoadconnection):

ConnectwiresperWIRINGDIAGRAMasfollows:

• GreenorbarecopperwireinwallboxtoGreenlead.

• Loadwallboxwireidentied(tagged)whenremovingoldswitchtoRedlead.

• FirstTravelerLineHottoBlacklead.

• RemoveRedinsulatinglabelfromYellow/Redlead.

• SecondTravelerwallboxwire(notecolorasabove)toYellow/Redlead.Thistraveler

fromthefancontrolmustgototheterminalscrewontheremotemarked"YL/RD".

• LineneutralwallboxwiretoWhitelead.

• ProceedtoStep5.

Foradditionalinformation,contactLeviton’sTechlineat

1-800-824-3005orvisitLeviton’swebsiteatwww.ViziaRFplus.com

• FandoesnotturnONandON/OFFLEDdoesnotturnON

 - Circuitbreakerorfusehastripped.

 - Fanhasburnedout.

 - FanNeutralconnectionisnotwired.

 - Conrmthatthedeviceisbeingsuppliedfroma120V,60HzACsourceONLY.

 - Conrmthatunitisprogrammedproperly.Repeat“TOINSTALL”sectionto

verifythatithasbeenincludedintheZ-Wave™network.

• Remotedoesnotoperatefan

 - Ensurethattotalwirelengthdoesnotexceed300ft.

TROUBLESHOOTING

Air-GapSwitch:

OntheFanSpeedControlonly,engagethe

air-gapswitchbygentlypressingthetopofthe

PushPaduntilthebottomliftscompletelyoutof

theframeandaclickisheard(refertoFigure).

Thiswillcutpowertothexture.Afterservicingis

complete,pressthePushPadbackintoplacefor

normaloperation.

Cleaning:Cleanwithadampcloth.

DO NOTusechemicalcleaners.

NOTE:ThelocatorlightwillilluminatewhentheloadisintheOFFpositionto

facilitateaccessinthedark.

NOTE:Ifusingthefanspeedcontrolina3-wayapplication,thefanwillturn

ONatspeedsetonfan’sFanSpeedbar.Thefanspeedcanbecontrolled

fromeitherthefanspeedcontrolortheremotelocation.

PushPad(Defaultsettings)

TurnONfromOFFposition:

Tap–FanturnsONtopresetspeed.

TurnOFFfromONposition:

Tap–FanturnsOFF.

Fan Speed Bar

PressFanSpeedBarrightorlefttoincreaseor

decreasefanspeedrespectively.

Thereare3speeds-High,MediumorLow.

INCREASE:

PresstherighthalfoftheFanSpeedBarto

increasefanspeed.

DECREASE:

PressthelefthalfoftheFanSpeedBarto

decreasefanspeed.

Ifyoucontinuetohold,thefanwillreducespeedto

minimumlevelandthenturnOFF.

NOTE:Thefanspeedcanbechangedwhenthe

fanisoffusingtheFanSpeedBar.Intheeventof

poweroutageorinterruptionthefanwillresetto

thelastfanspeedwhenpowerisrestored.

Push

Pad

Locator

Light

LED Fan

Speed

Display

Fan

Speed

Bar

OPERATION

NOTE:Dresswireswithabendasshownindiagram

inordertorelievestresswhenmountingdevice.

• Positionallwirestoprovideroominoutletwallbox

fordevice.

• Ensurethattheword“TOP”isfacingupondevice

strap.

• Partiallyscrewinmountingscrewsinwallbox

mountingholes.

• Restorepoweratcircuitbreakerorfuse.

• PressPushPadandfanshouldturnON.Iffandoes

notturnON,presstherighthalfoftheFanSpeed

BaruntilthefanturnsON.

If fan still does not turn ON, refer to the

TROUBLESHOOTING section.

TestingyourFanSpeedControlpriorto

mountinginwallbox:

Step5

RestorePower:

Restorepoweratcircuitbreakerorfuse. Installation is

complete.

Step 7

Fan Speed ControlMatchingRemote

YL/RD

Black

R ed

Yellow/Red

Green

White

Hot (Bla c k )

Neutral (White)

Fan Speed control Mat c hing Remote (with LEDs )

YL/RD

Bla c k

White

Red

Y e llow/Red

Fan

Line

120 V A C , 60H z

Green

G r oun d

Green

G r oun d

3-WayWiringwithMatchingRemote

(w/LEDs)Application:

Step4c

ADVANCEDPROGRAMMINGFEATURES

DenitionofAModes

A) PresetONSpeed:Setstheturnonfanspeedregardlessoftheprevious

speedset(FormerlySpeedLock).

DenitionofBModes

B) LEDOptions:SetsthetimeperiodinsecondstheLocatorLEDand

Brightnessdisplaywillstayonbeforeextinguishing.

NOTES:

• Thedevicewillexitprogrammingmodeafter3minutesofinactivity

• PressingthePushPadatanytimeduringprogrammingwilladvancethe

devicetothenextprogrammingmode.

ProgramModeA

ToenterProgramModeA:

PressandholdthePushPadandthentherighthalf

oftheFANSPEEDBar(

)for5secondsuntilthe

LocatorLEDandleftmostLED(LED1)beginstoblink.

• TheLocatorLEDwillblinkoncepersecondto

indicateProgramModeA,PresetONSpeed.To

changethecurrentPresetONSpeedfromHIGH

(LED7),MEDIUM(LED4),LOW(LED1),usethe

FANSPEEDBar.Ifthisfeatureisnotdesired,pressandholdthelefthalf

oftheFANSPEEDBar(

)untilnoLEDislit(defaultsetting).Bytapping

thePushPadthissettingwillautomaticallybesavedandthedevicewill

exitProgrammingModeA.

ProgramModeB

ToenterProgramModeB:

PressandholdthePushPadandthenthelefthalfoftheFANSPEEDBar(

)

for5secondsuntiltheLocatorLEDandrightmostLED(LED7)beginstoblink.

• TheLocatorLEDwillblinkoncepersecondtoindicateProgramModeB,

LED OptionsMode.TochangetheLED Optionssettings,usetheFAN

SPEEDBartomovetheLEDtothedesiredpresetsettingaccordingto

thechartbelow.BytappingthePushPadthissettingwillautomaticallybe

savedandthedevicewillexitProgrammingModeB.

LED Fan Speed

Display

1 4 7

LED

LED 1 (Default)

LED 4

LED 7

LED LOCATOR TIMEOUT

Active

Turns off 5 seconds after use

LED BRIGHTNESS DISPLAY TIMEOUT

Active

Turns off 5 seconds after use

Gentlypresstop

ofPushPad

NOTE:ThefanspeedcontrolmustbeinstalledinawallboxthathasaLoad

connection.ThematchingremotemustbeinstalledinawallboxwithaLineHot

connectionandaNeutralconnection.ANeutralwiretothematchingremoteneeds

tobeaddedasshown.

Ifyouareunsureaboutanypartoftheseinstructions,consultaqualiedelectrician.

NOTE:Maximumwirelengthfromfanspeedcontroltoallinstalledremotescannot

exceed300ft(90m).

WIRING MATCHING REMOTE

(wallboxwithLineHotconnection):

ConnectwiresperWIRINGDIAGRAMasfollows:

• GreenorbarecopperwireinwallboxtoGreenterminalscrew.

• LineHot(common)wallboxwireidentied(tagged)whenremovingold

switchandFirstTravelertoremoteterminalscrewmarked"BK".

• SecondTravelerwallboxwirefromfanspeedcontroltoremoteterminal

screwmarked"YL/RD"(notewirecolor).Thistravelerfromtheremote

mustgotothefancontrolYellow/Redlead.

• LineNeutralwallboxtoremoteterminalscrewmarked"WH".

FanSpeedControlMounting:

TURNOFFPOWERATCIRCUIT

BREAKER OR FUSE.

Installationmaynowbecompleted

bytighteningmountingscrewsinto

wallbox.Attachwallplate.

Step6

NOTES:

• Ifusinganon-LevitonProgrammer/Controller,

refertotheProgrammer/Controllerinstruction

sheetforIncludingadevice.

• IfusingtheVRCPG'sInstallChecklistfeature,

godirectlytoStepB.

A)IfusingaLevitonZ-Wave

Programmer/

Controller,Cat.No.VRCPG,presstheMenu

buttonandscrolldowntoSystemSetup.

ChooseAdvancedSettings.Pressthecenter

buttontoselectSystemSetupMenu.Pressthe

centerbuttontoselectNetwork.

B)Whilestandingclosetothemodule(approx.

2-5ft),pressthecenterbuttonto<Include>

deviceinthenetwork.

NOTE:Onlyonedevicemaybeincludedatatime.DO NOTput

multipledevicesintotheInclusionmodeatanytime.

C)WhiletheProgrammer/ControllerisintheInclusionmodeand

theLocatorLEDisONonthefanspeedcontrol,pushthepush

padtoturnONthefan.TheProgrammer/Controllerwillverify

inclusionandthelocatorLEDwillturnOFFonthefanspeed

control.IfthefanspeedcontrolisashingAmberwhileinthe

Inclusionmode,theProgrammer/Controllerisstilltryingto

communicatewiththefanspeedcontrol.Waituntilthedevice

stopsashing,thenpressthepushpad.

 NOTE:IfthelocatorLEDonthefanspeedcontrolturnssolid

Redwhileincluding,therehasbeenacommunicationerror.

RefertoTroubleshootingsection.

D)ThePrimaryProgrammer/ControllerwillassignanodeID

number(Name)forthismodule.

NOTE:ThisIDnumber(Name)willbestoredinthecontroller

librarytobeusedforfuturereference.

 NOTE:Youmayeditthename

ofthisdeviceatthistime.

E) The fan speed control is now

installed in the network.

NOTE:Ifafanspeedcontrol

hasbeensuccessfullyIncluded

inthenetworkandtheusertries

toIncludeitagainwithoutrst

excludingitfromthenetwork,the

modulewillretaintherstnode

IDithadreceivedandignorethe

second.

Programmer/Controller

Cat.No.VRCPG

Button

OFF

Center

Button

IncludingSceneCapableFanSpeed

ControlintoZ-Wave

Network:

VRCPG

Programmer/

Controller

NOTE:Remotemustbeinclose

proximitytofanspeedcontrolwhen

includinginnetwork.

FactoryDefault:

Ifyourfanspeedcontrolisnotresponding,oryouareunabletocontrolitafter

youhavetriedtoInclude/Excludeitmultipletimes,itmaybenecessaryto

resetthefanspeedcontroltoitsoriginalfactorysettings.Toaccomplishthis,

proceedasfollows:

• Onthefanspeedcontrol,engagetheair-gapswitch(refertoOperation

section)andwait5seconds.Presspushpadbackintoframeandhold

pushpaduntilthelocatorLEDturnsAmberandthenashesRed.Thefan

speedcontrolisnowreset.Oncethefanspeedcontrolisreset,itwillbe

necessarytoRe-Includeittoanetworkbeforeitcanbeused.

CAUTION:SETTINGADEVICETOAFACTORYDEFAULTDOES

NOTEXCLUDETHATDEVICEFROMANETWORK.THEEXCLUSION

PROCEDUREMUSTSTILLBEFOLLOWEDTOREMOVETHEDEVICE

FROMTHEPRIMARYCONTROLLER’SINFORMATIONTABLE.FAILURE

TODOSOMAYRESULTINASYSTEMTHATISSLOWTORESPOND,OR

MAYFAILTORESPONDTOSOMEDEVICES.

ExcludingFanSpeed

ControlfromNetwork:

NOTE:ItisveryimportanttoaccuratelyExcludedevicesfromthenetwork

whenmovingorremovingadevicefromaZ-Wave

network.Thisensures

thatallinformationhasbeenremovedfromyourPrimaryProgrammer/

Controller’sinformationtableandisnotcountedontobeapartofthemesh

network.

ProtectedunderU.S.PatentNumber6,388,399andpatentspending

andlicensedunderU.S.PatentsNumbers5,905,442,and5,982,103

ThisequipmenthasbeentestedandfoundtocomplywiththelimitsforaClassBDigitalDevice,

pursuanttoPart15oftheFCCRules.Theselimitsaredesignedtoprovidereasonableprotection

againstharmfulinterferenceinaresidentialinstallation.Thisequipmentgenerates,uses,andcan

radiateradiofrequencyenergyand,ifnotinstalledandusedinaccordancewiththeinstructions,may

causeharmfulinterferencetoradiocommunications.However,thereisnoguaranteethatinterference

willnotoccurinaparticularinstallation.Ifthisequipmentdoescauseharmfulinterferencetoradio

ortelevisionreception,whichcanbedeterminedbyturningtheequipmentOFFandON,theuseris

encouragedtotrytocorrecttheinterferencebyoneormoreofthefollowingmeasures:

• ReorientorrelocatethereceivingAntenna.

• Increasetheseparationbetweentheequipmentandthereceiver.

• Connecttheequipmentintoanoutletonacircuitdifferentfromthat

towhichthereceiverisconnected.

• Consultthedealeroranexperiencedradio/tvtechnicianforhelp.

FCCCOMPLIANCESTATEMENT

A)IfusingaLevitonZ-Wave

Programmer/Controller,Cat.No.VRCPG,pressthe

MenubuttonandscrolldowntoSystemSetup.ChooseAdvancedSettings.

PressthecenterbuttontoselectSystemSetupMenu.Pressthecenterbutton

toselectNetwork.

B)Whilestandingclosetothefanspeedcontrol,pressthecenterbuttonto

<Exclude>devicefromthenetwork.WhiletheProgrammer/Controllerisinthe

ExclusionmodeandthelocatorLEDisONonthefanspeedcontrol,press

thepushpadonthefanspeedcontrol.TheProgrammer/Controllerwillverify

ExclusionandthelocatorLEDwillturnOFFonthefanspeedcontrol.

 IfthefanspeedcontrolisashingAmberwhileintheExlusionmode,the

Programmer/Controllerisstilltryingtocommunicatewiththefanspeedcontrol.

Waituntilthedevicestopsashing,thenpressthepushpad.

Step8

Step9

Z-Wave VRF01-1LZ Operating instructions

Brand: Z-Wave

Model: VRF01-1LZ

Type: Operating instructions

This manual is also suitable for

031-VRF01-1LZ

Download PDF

report

Z-Wave VRF01-1LZ Operating instructions

This manual is also suitable for

Z-Wave VRF01-1LZ Operating instructions

Related papers

Other documents