Ranger design 6256 Installation guide

Type
Installation guide
INSTALLATION GUIDE
6256 BUCKET SEAT SET
Ford Transit Connect ( 2014-2016 )
For technical support, contact us at 1-800-565-5321 6256 Installation Guide | REV. A1 | Page 2
Phase 1 - Preparation
Phase 2 - Installation
q 1.1 Remove Headrests.
q 2.1 Install Seat Bottom Cover.
q 2.2 Install Seat Back Cover.
q 2.3 Install Headrest Cover.
QUICK START GUIDE
BILL OF MATERIALS
General care instructions:
1. In most cases dirt, debris, spills and pet hair can be removed by wiping with a
damp cloth.
2. Seat covers can be removed and machine washed on low temperature setting
using mild detergent.
Drip dry or machine tumble dry on a no heat cycle.
Straps should be coiled and secured with rubber bands for machine washing
and drying.
3. Soil may be removed with spray cleaner or detergent and water.
4. Oil or grease stains should rst be treated with a dry cleaning solvent followed
by a spray cleaner or detergent and water.
5. Do not use bleach.
Item No. Description Qty.
62-563 Seat Back Cover Passenger Side 1
62-561 Seat Bottom Cover Passenger Side 1
62-564 Headrest Cover Passenger Side 1
62-562 Seat Back Cover Driver Side 1
62-560 Seat Bottom Cover Driver Side 1
62-565 Headrest Cover Driver Side 1
For technical support, contact us at 1-800-565-5321 6256 Installation Guide | REV. A1 | Page 3
PHASE 1 – PREPARATION
1.1 REMOVING
q 1.1 Remove Headrests.
q Pull headrests out of the seats by pressing the tabs at the
base of the headrests and pulling up. Press the small tab on
the inside of the headrest mount with a paperclip or small pick.
q 2.1 Install Seat Bottom Cover.
q Ensure the tag inside the cover corresponds with the seat you are working on.
Each cover will have a Driver or Passenger tag.
q Lean seat back.
q Undo elasc straps from under seat boom to release seat back ap.
q Push ap on top of cover between seat back and seat boom.
q Tuck sides of cover behind plasc trim.
q Push strings between seat boom and plasc trim. They will go through where the seat back
and boom meet.
q Pull strings behind seat and pull ght.
q Tie a loop in one string, close to the edge of the seat.
q Run the other string through the loop and pull as ght as possible. This is what keeps your seat
boom from shiing.
q Pull boom aps from front of seat boom and aach to top ap under the rear of the seat.
q Flaps MUST run OVER bars and brackets under seat.
PHASE 2 – DRIVER’S SEAT COVER INSTALLATION
2.1 SEAT COVER INSTALLATION
2 STRAPS UNDER SEAT
Seat cover bottom ap, running OVER all bars,
For technical support, contact us at 1-800-565-5321 6256 Installation Guide | REV. A1 | Page 4
q 2.2 Install Seat Back Cover.
q Ensure the tag inside the cover corresponds
with the seat you are working on.
Each cover will have a Driver or Passenger tag.
q Turn cover 3/4 of the way inside out.
q Pull cover over seat back, pulling ght against the
top of the seat.
q Align the holes in the cover with the headrest
holes on the seat back.
q Work the plasc trim around the headrest holes
through the holes in the seat cover.
q Pull the cover down over the seat, unrolling as you
go.
q Push the front ap of the cover between the
seat back and seat boom.
q Pull ap ght and fasten to Velcro under seat
boom.
q Re-aach elasc straps under seat boom.
q Pull the rear ap ght and fasten to Velcro under
seat boom.
For technical support, contact us at 1-800-565-5321 6256 Installation Guide | REV. A1 | Page 5
PHASE 3 – PASSENGER’S SEAT COVER INSTALLATION
3.1 SEAT COVER INSTALLATION
q Ensure the tag inside the cover corresponds with the
seat you are working on.
Each cover will have a Driver or Passenger tag.
q Undo elasc strap holding seat back ap from under
seat boom (Black strap with white clip).
q Tip seat back ap up and tuck inside seat cover as
you pull it down.
q Turn seat cover 3/4 of the way inside out.
q Pull seat back cover into posion, making sure that
the holes in the cover align with the holes in
the seat back.
q Stretch the cover over the headrest holes.
q Connue pulling the cover down the seat back,
turning it right side out as you go.
q Push ap from front of cover between seat back and
seat boom, out the back of the seat .
q Lean the seat back all the way forward.
q Pull the ap ght and aach to the Velcro on the
back of the seat.
For technical support, contact us at 1-800-565-5321 6256 Installation Guide | REV. A1 | Page 6
q Ensure the tag inside the cover corresponds with the seat you are working on.
Each cover will have a Driver or Passenger tag.
q Lean seat back.
q Undo elasc straps from under seat boom to release seat back ap.
q Push ap on top of cover between seat back and seat boom.
q Tuck sides of cover behind plasc trim.
q Push strings between seat boom and plasc trim. They will go through where the seat back
and boom meet.
q Pull strings behind seat and pull ght.
q Tie a loop in one string, close to the edge of the seat.
q Run the other string through the loop and pull as ght as possible. This is what keeps your
seat boom from shiing.
q Pull boom aps from front of seat boom and aach to top ap under the rear of the seat.
q Flaps MUST run OVER bars and brackets under seat.
Seat cover bottom ap, running OVER all bars,
q 3.2 Install Seat Bottom Cover.
For technical support, contact us at 1-800-565-5321 6256 Installation Guide | REV. A1 | Page 7
q 3.3 Install Headrest Covers.
q Put headrests back on seats.
q Press tabs at base of headrest and push headrest into seat back.
q Pull headrest cover over headrest with “hook” Velcro on
the back and “loop” Velcro on the front.
q Pull front ap over back ap and fasten.
For technical support, contact us at 1-800-565-5321 6256 Installation Guide | REV. A1 | Page 8
“Congratulations, you have successfully installed your
Seat Cover Set!
Thank you for doing business with us.”
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8

Ranger design 6256 Installation guide

Type
Installation guide

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI