Ranger design 6257-19 Installation guide

Brand
Ranger design
Model
6257-19
Type
Installation guide

Ranger design 6257-19 is a seat cover set compatible with Mercedes Benz Sprinter (2018-2019). It includes seat back covers, seat bottom covers, and headrest covers for both driver and passenger seats. The covers can protect your seats from dirt, debris, spills and pet hair. They are made of durable material that is easy to clean and maintain. The covers can be removed and machine washed on a low temperature setting using mild detergent. They can also be spot cleaned with a spray cleaner or detergent and water. The covers are designed to fit snugly over your seats and stay in place, even during use. They have a variety of features to ensure a comfortable and secure fit, including:

Ranger design 6257-19 is a seat cover set compatible with Mercedes Benz Sprinter (2018-2019). It includes seat back covers, seat bottom covers, and headrest covers for both driver and passenger seats. The covers can protect your seats from dirt, debris, spills and pet hair. They are made of durable material that is easy to clean and maintain. The covers can be removed and machine washed on a low temperature setting using mild detergent. They can also be spot cleaned with a spray cleaner or detergent and water. The covers are designed to fit snugly over your seats and stay in place, even during use. They have a variety of features to ensure a comfortable and secure fit, including:

INSTALLATION GUIDE
6257-19 BUCKET SEAT SET
Mercedes Benz Sprinter ( 2018-2019 )
For technical support, contact us at 1-800-565-5321 6257-19 Installation Guide | REV. A1 | Page 2
Phase 1 - Preparation
Phase 2 - Installation
q 1.1 Remove Headrests.
q 1.2 Raise seat up, slide forward and lean back forward.
q 2.1 Install Seat Back Cover.
q 2.2 Install Seat Bottom Cover.
q 2.3 Install Headrest Cover.
QUICK START GUIDE
BILL OF MATERIALS
General care instructions:
1. In most cases dirt, debris, spills and pet hair can be removed by wiping with a
damp cloth.
2. Seat covers can be removed and machine washed on low temperature setting
using mild detergent.
Drip dry or machine tumble dry on a no heat cycle.
Straps should be coiled and secured with rubber bands for machine washing
and drying.
3. Soil may be removed with spray cleaner or detergent and water.
4. Oil or grease stains should rst be treated with a dry cleaning solvent followed
by a spray cleaner or detergent and water.
5. Do not use bleach.
Item No. Description Qty.
62-573 Seat Back Cover Passenger Side 1
62-571 Seat Bottom Cover Passenger Side 1
62-574 Headrest Cover Passenger Side 1
62-572 Seat Back Cover Driver Side 1
62-573 Seat Bottom Cover Driver Side 1
62-574 Headrest Cover Driver Side 1
For technical support, contact us at 1-800-565-5321 6257-19 Installation Guide | REV. A1 | Page 3
PHASE 1 – PREPARATION
1.1 REMOVING
PHASE 2 – INSTALLATION
2.1 SEAT COVER INSTALLATION
q 1.1 Remove Headrests.
q Pull headrests out of the seats
by pressing the tabs at the base of the headreasts.
q Slide seat forward, raise up, and lean seat back forward.
q 2.1 Install Seat Back Cover.
q Ensure the tag inside the cover corresponds with the seat you are working on.
Each cover will have a Driver or Passenger tag.
q Turn seat cover 3/4 of the way inside out.
q Pull seat back cover into posion, making sure that the holes in the cover align
with the holes in the seat back.
q Stretch the cover over the headrest holes.
q Connue pulling the cover down the seat back, turning it right side out as you go.
q Push ap from front of cover between seat back and seat boom, out the back of the seat .
q Double the end of the ap over to prevent the “hook” Velcro
from scking to the factory upholstery.
q Pull the ap ght and aach to the Velcro on the back of the seat.
q Fasten ap under the armrest.
For technical support, contact us at 1-800-565-5321 6257-19 Installation Guide | REV. A1 | Page 4
q 2.2 Install Seat Bottom Cover.
q Put cover over seat boom.
q Tuck strings between seat boom and
tr im , w he re th e b ac k a nd bo om meet .
q Tuck sides of cover behind plasc trim.
q Pull strings ght.
q Tie a loop in one string. Run the other string through
the loop, pull ght, and e string back on itself. It is im-
portant to pull ght as this is what keeps your cover from
shiing.
q Push top ap between seat back and seat boom.
q Run front ap over seat adjustment lever, wires, and
brackets.
q Pull front ap ght and fasten to Velcro on top ap.
For technical support, contact us at 1-800-565-5321 6257-19 Installation Guide | REV. A1 | Page 5
q 2.3 Install Headrest Covers.
q Put headrests back on seats.
q Press tabs at base of headrest and push headrest into seat back.
q Pull headrest cover over headrest with “hook” Velcro on
the back and “loop” Velcro on the front.
q Pull front ap over back ap and fasten.
For technical support, contact us at 1-800-565-5321 6257-19 Installation Guide | REV. A1 | Page 6
“Congratulations, you have successfully installed your
Seat Cover Set!
Thank you for doing business with us.”
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6

Ranger design 6257-19 Installation guide

Brand
Ranger design
Model
6257-19
Type
Installation guide

Ranger design 6257-19 is a seat cover set compatible with Mercedes Benz Sprinter (2018-2019). It includes seat back covers, seat bottom covers, and headrest covers for both driver and passenger seats. The covers can protect your seats from dirt, debris, spills and pet hair. They are made of durable material that is easy to clean and maintain. The covers can be removed and machine washed on a low temperature setting using mild detergent. They can also be spot cleaned with a spray cleaner or detergent and water. The covers are designed to fit snugly over your seats and stay in place, even during use. They have a variety of features to ensure a comfortable and secure fit, including:

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents