B-K lighting Path Star Installation guide

Brand
B-K lighting
Model
Path Star
Type
Installation guide
REFERENCE NUMBER
INS000733
40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX 559.438.5900
www.bklighting.com • [email protected]
B-K LIGHTING
THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION OF B-K LIGHTING, INC. AND ITS RECEIPT OR POSSESSION DOES NOT CONVEY ANY RIGHTS TO REPRODUCE, DISCLOSE ITS CONTENTS, OR TO MANUFACTURE, USE OR SELL ANYTHING IT MAY
DESCRIBE. REPRODUCTION, DISCLOSURE OR USE WITHOUT SPECIFIC WRITTEN AUTHORIZATION OF B-K LIGHTING, INC. IS STRICTLY FORBIDDEN.
PS™ / BS™/ PSL™ / BSL™
Installation Instructions
IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE THESE INSTALLATION INSTRUCTIONS
This set of instructions works for:
PS - Path Star™
BS - Bollard Star™
PSL - Louvered Path Star™
BSL - Louvered Bollard Star™
BS
(33mm)
1 5/16"
(76mm)
3"
Specify
Length
BS-LED
S000891
1 3/8"
(35mm)
(4) 3/8" Dia. (10mm)
Bolt Holes
Slip Anchor
(38mm)
2" Dia. (51mm)
O.C.
Slip Conduit Hole
1 1/2"
3 1/2" O.C.
(89mm)
68° Angle = A
90° Angle = B
5"
(127mm)
PS
Anchor Base
RELEASE DATE
5-23-18
Warning Flammable Hot Surface
TECHNOLOGY
with TECHNOLOGY
psl bsl
psl bsl
PSL
BSL
• Product must be installed by a qualified person in a manner
consistent with its intended use and in compliance with the
National Electrical Code, Canadian Electrical Code, and all Local
and Provincial Codes.
• Follow product label information and instructions.
• Qualified Personnel must perform all servicing or relamping of
this product.
• Before wiring to power supply and during servicing or relamping,
turn off power at fuse or circuit breaker before service.
• The use of accessory equipment not recommended by the
manufacturer or installed contrary to instructions may cause an
unsafe condition. The use of damaged components may cause
an unsafe condition and void product warranty.
IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE ALL SAFETY
AND INSTALLATION INSTRUCTIONS
• Do not block light emanating from product in whole or part,
as this may cause an unsafe condition.
• Never operate the fixture with missing or damaged lens.
Lens must be cleaned on regular basis.
• Entire fixture may become extremely hot. Do not touch hot
lens or fixture body. Do not touch the lamp at any time. Use
a clean, dry, soft cloth to handle the lamp. Oil from skin may
damage the lamp and cause it to rupture.
• Replace lamp only with correct wattage and type of lamp
marked on fixture label.
• All gaskets, o-rings and sealing surfaces must be kept clean
during installation and service; failure to do this may cause an
unsafe condition and void product warranty.
INSTRUCTIONS PERTAINING TO
A RISK OF FIRE, OR INJURY TO
PERSONS IMPORTANT SAFETY
INSTRUCTIONS
Lighted lamp is HOT!
WARNING - To reduce the risk of FIRE OR INJURY TO PERSONS:
Turn off/unplug and allow to cool before replacing lamp.
Lamp gets HOT quickly! Contact only switch/plug when
turning on.
Do not touch hot lens, guard, or enclosure (see diagram/
picture).
Keep lamp away from materials that may burn.
Do no touch the lamp at any time. Use a soft cloth. Oil
from skin may damage lamp.
Do not operate the luminaire fitting with a missing or
damaged shield.
SAVE THESE INSTRUCTIONS
· Suitable for wet locations • Suitable for mounting within 4 ft. of the ground.
IMPORTANT LISTINGS AND CERTIFICATIONS
High Voltage
TOOLS
NEEDED:
By Others
1/8” Allen Wrench
Waterproof Wire Connectors
Mounting Hardware
Drill
& Low Voltage
RELEASE DATE
5-23-18
40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX 559.438.5900
www.bklighting.com • [email protected]
B-K LIGHTING
IMPORTANT SAFETY INFORMATION LISTED ON REVERSE
READ, FOLLOW, AND SAVE ALL SAFETY AND INSTALLATION INSTRUCTIONS
Remote Transformer
5. Make watertight connections from remote
transformer to fixture source leads using
waterproof wire connectors (By Others). See
wiring diagram.
4. Pull low voltage wire or pull branch circuit
wires necessary for installation (By Others)
through anchor base.
Anchor base can accommodate up to two (2)
1/2” conduits.
7. Place fixture on anchor base and tighten four
(4) #10-32 stainless steel button head cap
screws using a 1/8” Allen wrench.
120V 12V
Fixture
COM
Remote
Transformer
COM
120V 12V
Fixture
COM
GROUND
Integral
Transformer
COM
GROUND
Integral Transformer
6. Use waterproof wire connectors
(By Others) to make watertight connections
from transformer primary leads to branch circuit
wires. Connect incoming ground to ground wire
provided in fixture body. See wiring diagram.
WIRING DIAGRAM
3.50
1.50
1. Determine suitable anchors (By Others) to
attach anchor base to architectural surface.
2. Place provided template in final mounting
position according to designed lighting plan.
3. Drill holes into surface for maximum 7/16”
fasteners (By Others) on locations illustrated
on template. Base mounting hole locations is
1-1/2” on center by 3-1/2” on center apart.
PROJECT:
TYPE:
(33mm)
1 5/16"
(76mm)
3"
Specify
Length
BS-LED
S000891
1 3/8"
(35mm)
(4) 3/8" Dia. (10mm)
Bolt Holes
Slip Anchor
(38mm)
2" Dia. (51mm)
O.C.
Slip Conduit Hole
1 1/2"
3 1/2" O.C.
(89mm)
68° Angle = A
90° Angle = B
5"
(127mm)
PS™ / BS™/ PSL™ / BSL™
Installation Instructions
REFERENCE NUMBER
INS000733
TECHNOLOGY
with TECHNOLOGY
Anchor Base Installation
TRANSFORMER HOUSING MUST BE INSTALLED ABOVE GRADE.
TRANSFORMER HOUSING INSTALLED BELOW GRADE WILL VOID WARRANTY
& Low Voltage
120V 12V
Fixture
COM
Remote
Transformer
COM
120V 12V
Fixture
COM
GROUND
Integral
Transformer
COM
GROUND
WIRING DIAGRAM
8. Use 1/8” Allen wrench to loosen #10-24 stainless
faceplate screws to remove faceplate. for access
to source.
5"
3"
3 1/2"
1 1/2"
4 X
7/16" Dia.
NOTES: Full Scale Anchor Bolt Template
DRAWING NUMBER
BASE,PS,MACH,ALU
511085
5/15/08
THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION OF B-K LIGHTING AND ITS RECEIPT OR POSSESSION
DOES NOT CONVEY ANY RIGHTS TO REPRODUCE, DISCLOSE ITS CONTENTS, OR TO MANUFACTURE, USE OR
SELL ANYTHING IT MAY DESCRIBE. REPRODUCTION, DISCLOSURE OR USE WITHOUT SPECIFIC WRITTEN
AUTHORIZATION OF B-K LIGHTING IS STRICTLY FORBIDDEN.
WARNING!
Template must print at proper scale.
Verify dimensions prior to use.
REFERENCE NUMBER
INS000733.1
40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX 559.438.5900
www.bklighting.com • [email protected]
B-K LIGHTING
THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION OF B-K LIGHTING, INC. AND ITS RECEIPT OR POSSESSION DOES NOT CONVEY ANY RIGHTS TO REPRODUCE, DISCLOSE ITS CONTENTS, OR TO MANUFACTURE, USE OR SELL ANYTHING IT MAY
DESCRIBE. REPRODUCTION, DISCLOSURE OR USE WITHOUT SPECIFIC WRITTEN AUTHORIZATION OF B-K LIGHTING, INC. IS STRICTLY FORBIDDEN.
PS™ / PSL™
Installation Instructions
IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE THESE INSTALLATION INSTRUCTIONS
1 3/8"
35mm
68° Angle = A
S000733
PS-LED
1 3/8"
(35mm)
3/8" Dia. (10mm)
Bolt Holes
(38mm)
Slip Anchor
2" Dia. (51mm)
Slip Conduit Hole
1 1/2" O.C.
3 1/2"O.C.
(89mm)
Optional
Stability
Flange
5 7/8" Dia.
(149mm)
8"
(203mm)
3"
76mm
90° Angle = B
5"
(127mm)
Standard
Base Pipe
Stake
TOOLS
NEEDED:
By Others
1/8” Allen Wrench
Waterproof Wire Connectors
Mounting Hardware
PS
This set of instructions works for:
PS - Path Star™
PSL - Louvered Path Star™
18 Gauge Wire
Anchor Base
on Power PipeTM
Stability Flange
RELEASE DATE
5-23-18
Warning Flammable Hot Surface
TECHNOLOGY
with TECHNOLOGY
• Product must be installed by a qualified person in a manner
consistent with its intended use and in compliance with the
National Electrical Code, Canadian Electrical Code, and all Local
and Provincial Codes.
• Follow product label information and instructions.
• Qualified Personnel must perform all servicing or relamping of
this product.
• Before wiring to power supply and during servicing or relamping,
turn off power at fuse or circuit breaker before service.
• The use of accessory equipment not recommended by the
manufacturer or installed contrary to instructions may cause an
unsafe condition. The use of damaged components may cause
an unsafe condition and void product warranty.
IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE ALL SAFETY
AND INSTALLATION INSTRUCTIONS
• Do not block light emanating from product in whole or part,
as this may cause an unsafe condition.
• Never operate the fixture with missing or damaged lens.
Lens must be cleaned on regular basis.
• Entire fixture may become extremely hot. Do not touch hot
lens or fixture body. Do not touch the lamp at any time. Use
a clean, dry, soft cloth to handle the lamp. Oil from skin may
damage the lamp and cause it to rupture.
• Replace lamp only with correct wattage and type of lamp
marked on fixture label.
• All gaskets, o-rings and sealing surfaces must be kept clean
during installation and service; failure to do this may cause an
unsafe condition and void product warranty.
INSTRUCTIONS PERTAINING TO
A RISK OF FIRE, OR INJURY TO
PERSONS IMPORTANT SAFETY
INSTRUCTIONS
Lighted lamp is HOT!
WARNING - To reduce the risk of FIRE OR INJURY TO PERSONS:
Turn off/unplug and allow to cool before replacing lamp.
Lamp gets HOT quickly! Contact only switch/plug when
turning on.
Do not touch hot lens, guard, or enclosure (see diagram/
picture).
Keep lamp away from materials that may burn.
Do no touch the lamp at any time. Use a soft cloth. Oil
from skin may damage lamp.
Do not operate the luminaire fitting with a missing or
damaged shield.
SAVE THESE INSTRUCTIONS
· Suitable for wet locations • Suitable for mounting within 4 ft. of the ground.
IMPORTANT LISTINGS AND CERTIFICATIONS
High Voltage
psl bsl
PSL
& Low Voltage
Proper soil preparation is recommended before installation. See the DIG-IT guide at www.bklighting.com/dig-it for more information.
RELEASE DATE
5-23-18
40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX 559.438.5900
www.bklighting.com • [email protected]
B-K LIGHTING
IMPORTANT SAFETY INFORMATION LISTED ON REVERSE
READ, FOLLOW, AND SAVE ALL SAFETY AND INSTALLATION INSTRUCTIONS
1 3/8"
35mm
68° Angle = A
S000733
PS-LED
1 3/8"
(35mm)
3/8" Dia. (10mm)
Bolt Holes
(38mm)
Slip Anchor
2" Dia. (51mm)
Slip Conduit Hole
1 1/2" O.C.
3 1/2"O.C.
(89mm)
Optional
Stability
Flange
5 7/8" Dia.
(149mm)
8"
(203mm)
3"
76mm
90° Angle = B
5"
(127mm)
Standard
Base Pipe
Stake
PS™ / PSL™
Installation Instructions
REFERENCE NUMBER
INS000733.1
Finished grade Concrete
Finished grade
Finished grade Optional
Stability Flange
Pea gravel
or sand
Finished grade
Pea gravel
or sand
Pea gravel
or sand
Above Ground
Finished grade
Pea gravel
or sand
Pea gravel
or sand
Above Ground
Finished grade Concrete
Below Ground
Finished grade
Pea gravel
or sand
3. Pull branch circuit wiring necessary for
installation (By Others) to Power Pipe™. Place
Power Pipe™ in hole.
Allow for additional cable to make connections
to fixture leads and future service. Do not cut
PVC.
2. Slide optional Stability Flange onto Power
Pipe™. Use optional Stability Flange to aid in
installation of Power Pipe™.
1. Excavate trench according to designed lighting
plan. Dig hole a minimum of 18” deep and 10”
wide to accommodate Power Pipe™ at desired
fixture locations.
Power Pipe with Anchor Base Mounting Option
Finished grade Concrete
Finished grade
Finished grade Optional
Stability Flange
Pea gravel
or sand
Finished grade
Pea gravel
or sand
Pea gravel
or sand
Above Ground
Finished grade
Pea gravel
or sand
Pea gravel
or sand
Above Ground
Finished grade Concrete
Below Ground
Finished grade
Pea gravel
or sand
4. Back fill with pea gravel or sand prior to pour.
Finished grade Concrete
Finished grade
Finished grade Optional
Stability Flange
Pea gravel
or sand
Finished grade
Pea gravel
or sand
Pea gravel
or sand
Above Ground
Finished grade
Pea gravel
or sand
Pea gravel
or sand
Above Ground
Finished grade Concrete
Below Ground
Finished grade
Pea gravel
or sand
5. Pour concrete (By Others).
Label on Power Pipe™ indicates installation
depth with finished grade.
Remote
Transformer
Remote Transformer
6. Make watertight connections from remote 12V
transformer to LED source leads (18 gauge wire)
using waterproof wire connectors (By Others).
See wiring diagram.
TECHNOLOGY
with TECHNOLOGY
TRANSFORMER HOUSING MUST BE INSTALLED ABOVE GRADE. POWER PIPE™ IS LABELED AT GRADE LEVEL.
TRANSFORMER HOUSING INSTALLED BELOW GRADE WILL VOID WARRANTY
& Low Voltage
Soil Prep
Conduit
trench
B. Dig hole 10” wide and 24” deep.
Conduit
Trench
Excavated
for Housing
C. Prep soil according to DIG-IT Guide.
A. Determine Soil Type by referencing DIG-IT Guide.
Prep soil according to DIG-IT Guide.
1 3/8"
35mm
68° Angle = A
S000733
PS-LED
1 3/8"
(35mm)
3/8" Dia. (10mm)
Bolt Holes
(38mm)
Slip Anchor
2" Dia. (51mm)
Slip Conduit Hole
1 1/2" O.C.
3 1/2"O.C.
(89mm)
Optional
Stability
Flange
5 7/8" Dia.
(149mm)
8"
(203mm)
3"
76mm
90° Angle = B
5"
(127mm)
Standard
Base Pipe
Stake
PS™ / PSL™
Installation Instructions
TECHNOLOGY
with TECHNOLOGY
& Low Voltage
RELEASE DATE
5-23-18
40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX 559.438.5900
www.bklighting.com • [email protected]
B-K LIGHTING
IMPORTANT SAFETY INFORMATION LISTED ON REVERSE
READ, FOLLOW, AND SAVE ALL SAFETY AND INSTALLATION INSTRUCTIONS
REFERENCE NUMBER
INS000733.1
Integral Transformer
7. Pull branch circuit wires necessary for
installation (By Others) through Power Pipe™.
Use waterproof wire connectors (By Others) to
connect transformer primary leads to branch
circuit wires. Connect incoming ground to
ground wire provided in fixture body. See
wiring diagram.
120V 12V
Fixture
COM
Remote
Transformer
COM
120V 12V
Fixture
COM
GROUND
Integral
Transformer
COM
GROUND
WIRING DIAGRAM
8. Place fixture on anchor base and tighten four (4)
#10-32 stainless steel button head cap screws
using a 1/8” Allen wrench.
Integral
Transformer
9. Use 1/8” Allen wrench to loosen #10-24 stainless
faceplate screws to remove faceplate for access
to source.
120V 12V
Fixture
COM
Remote
Transformer
COM
120V 12V
Fixture
COM
GROUND
Integral
Transformer
COM
GROUND
WIRING DIAGRAM
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6

B-K lighting Path Star Installation guide

Brand
B-K lighting
Model
Path Star
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents