B-K lighting Power Pipe Installation guide

Brand
B-K lighting
Model
Power Pipe
Type
Installation guide
RELEASED
12-13-16
REFERENCE NUMBER
INS001284
40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX 559.438.5900
www.bklighting.com • [email protected]
B-K LIGHTING
THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION OF B-K LIGHTING, INC. AND ITS RECEIPT OR POSSESSION DOES NOT CONVEY ANY RIGHTS TO REPRODUCE, DISCLOSE ITS CONTENTS, OR TO MANUFACTURE, USE OR SELL ANYTHING IT MAY
DESCRIBE. REPRODUCTION, DISCLOSURE OR USE WITHOUT SPECIFIC WRITTEN AUTHORIZATION OF B-K LIGHTING, INC. IS STRICTLY FORBIDDEN.
IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE THESE INSTALLATION INSTRUCTIONS
TOOLS
REQUIRED:
By Others
Waterproof Wire Connectors
5/64” Allen Wrench
Phillips Screwdriver
POWER PIPE™ SYSTEM
Power Pipe™ Junction Box Installation Instructions
• Product must be installed by a qualified person in a manner
consistent with its intended use and in compliance with the
National Electrical Code, Canadian Electrical Code, and all Local
and Provincial Codes.
• Follow product label information and instructions.
• Qualified Personnel must perform all servicing or relamping of
this product.
• Before wiring to power supply and during servicing or relamping,
turn off power at fuse or circuit breaker before service.
• The use of accessory equipment not recommended by the
manufacturer or installed contrary to instructions may cause an
unsafe condition. The use of damaged components may cause
an unsafe condition and void product warranty.
IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE ALL SAFETY
AND INSTALLATION INSTRUCTIONS
• Do not block light emanating from product in whole or part,
as this may cause an unsafe condition.
• Never operate the fixture with missing or damaged lens.
Lens must be cleaned on regular basis.
• Entire fixture may become extremely hot. Do not touch hot
lens or fixture body. Do not touch the lamp at any time. Use
a clean, dry, soft cloth to handle the lamp. Oil from skin may
damage the lamp and cause it to rupture.
• Replace lamp only with correct wattage and type of lamp
marked on fixture label.
• All gaskets, o-rings and sealing surfaces must be kept clean
during installation and service; failure to do this may cause an
unsafe condition and void product warranty.
INSTRUCTIONS PERTAINING TO
A RISK OF FIRE, OR INJURY TO
PERSONS IMPORTANT SAFETY
INSTRUCTIONS
Lighted lamp is HOT!
WARNING - To reduce the risk of FIRE OR INJURY TO PERSONS:
Turn off/unplug and allow to cool before replacing lamp.
Lamp gets HOT quickly! Contact only switch/plug when
turning on.
Do not touch hot lens, guard, or enclosure (see diagram/
picture).
Keep lamp away from materials that may burn.
Do no touch the lamp at any time. Use a soft cloth. Oil
from skin may damage lamp.
Do not operate the luminaire fitting with a missing or
damaged shield.
SAVE THESE INSTRUCTIONS
· Suitable for wet locations
IMPORTANT LISTINGS AND CERTIFICATIONS
Warning High Voltage
Box With Integral
12V or 12V or
With 'B' Cap
Power Pipe Junction Box Power Pipe Junction
Fixtures With 'C' Cap
Transformer For Remote
Box With Integral
Transformer With 'B' Cap
Power Pipe Junction
120V/230V/277V In 120V/230V/277V Out 120V/230V/277V In 12V Out 120V/230V/277V In 12V or 120V/230V/277V Out
Grade Grade
or UF CableConduit or UF CableConduit or UF CableConduit
Fixtures With 'C' Cap
Power Pipe Stake
Power Pipe Stake
With Integral Transformer With 'B' Cap
120V/230V/277V In
Transformer For Remote
With Integral
12V Out
12V or
12V or 120V/230V/277V Out
With 'B' Cap
Power Pipe Stake
Grade Grade
120V/230V/277V In
12V or
or UF CableConduit or UF CableConduit or UF CableConduit
120V/230V/277V In 120V/230V/277V In
12V Out
Power Pipe
Adjustable Stem
12V In
Grade
or UF CableConduit
GRADE
Stability Flange™
Specify Fixture
Separately
12V In 12V Out 120V In 12V Out 120V In 12V or
120V Out
12V or
120V Out
Conduit or UF Cable Conduit or UF Cable
Conduit or UF Cable
GRADEGRADE
Power Pipe™
Junction Box
with ‘B’ Cap
Power Pipe™
Junction Box
with integral 75VA
transformer for
remote fixtures
with ‘C’ Cap
Power Pipe™
Junction Box
with integral 75VA
transformer
with ‘B’ Cap
with integral 75VA
transformer for
remote fixtures
with ‘C’ Cap
with integral 75VA
transformer
with ‘B’ Cap
12V In 12V Out
Power Pipe™
Stake
with ‘B’ Cap
GRADE
12V Out
Power Pipe™
Stake
GRADE
120V In120V In
Power Pipe™
Stake
GRADE
12" or
18"
2" Dia. PVC
Housing
Two 1/2"
PVC Slip
Connectors
PP Stake ‘S’
PP Junction ‘J ’
12" or
18"
2" Dia. PVC
Housing
Hot Surface
Specify Fixture
Separately
Please refer to the low voltage
design guide at www.bklighting.
com/lvguide before installation for
proper wire selection.
Grade Level Label
Proper soil preparation is
recommended before installation. See
the DIG-IT guide at www.bklighting.
com/dig-it for more information.
40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX 559.438.5900
www.bklighting.com • [email protected]
B-K LIGHTING
IMPORTANT SAFETY INFORMATION LISTED ON REVERSE
READ, FOLLOW, AND SAVE ALL SAFETY AND INSTALLATION INSTRUCTIONS
RELEASED
12-13-16
REFERENCE NUMBER
INS001284
POWER PIPE™ SYSTEM
Power Pipe™ Junction Box Installation Instructions
2. Connect conduit to the 1/2” conduit couplers
attached to the bottom of the Power Pipe™.
Place Power Pipe™ in hole.
3. Back fill hole with soil and/or prep for concrete.
4. Pull branch circuit or low voltage wiring
necessary for appropriate installation (By
Others).
1. Excavate trench according to designed lighting plan.
Dig hole a minimum of 24” deep and 10” wide to
accommodate Power Pipe™ at desired fixture
locations. Do not cut PVC..
INSTALLATION OF POWER PIPE™ JUNCTION BOX
Finished grade
Pea gravel or sand
Concrete or Dirt
Finished grade
Finished grade
Pea gravel or sand
Concrete or Dirt
Finished grade
Finished grade
Pea gravel or sand
Concrete or Dirt
Finished grade
1. Make watertight connections from remote 12V
transformer to fixture leads using waterproof wire
connectors. (By Others)
JUNCTION BOX WITH “B” CAP:
2. Attach B cap to Power Pipe™ with (3) #8-32
round head Phillips stainless steel screws at
base to secure to Power Pipe™ with Phillips
screwdriver.
120V 12V
Fixture
COM
Remote
Transformer
COM
120V 12V
Fixture
COM
GROUND
WIRING DIAGRAM
Integral
Transformer
COM
GROUND IN HOUSING
WIRING DIAGRAM
TRANSFORMER HOUSING MUST BE INSTALLED ABOVE GRADE. POWER PIPE™ IS LABELED AT GRADE LEVEL.
TRANSFORMER HOUSING INSTALLED BELOW GRADE WILL VOID WARRANTY
Soil Prep
Conduit
trench
B. Dig hole 10” wide and 24” deep.
Conduit
Trench
Excavated
for Housing
C. Prep soil according to DIG-IT Guide.A. Determine Soil Type by referencing DIG-IT Guide.
Prep soil according to DIG-IT Guide.
Failure to use waterproof wire connectors
will cause fixture to fail and VOID PRODUCT
WARRANTY.
40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX 559.438.5900
www.bklighting.com • [email protected]
B-K LIGHTING
IMPORTANT SAFETY INFORMATION LISTED ON REVERSE
READ, FOLLOW, AND SAVE ALL SAFETY AND INSTALLATION INSTRUCTIONS
RELEASED
12-13-16
REFERENCE NUMBER
INS001284
POWER PIPE™ SYSTEM
Power Pipe™ Junction Box Installation Instructions
WIRING DIAGRAM 4. Place transformer and connectors into
T-housing. Attach B cap to T-housing with
(3) #8-32 stainless steel set screws using 5/64”
Allen wrench.
3. Make watertight connections from primary
branch circuit wiring to primary side of
transformer using waterproof wire connectors.
(By Others). Attach secondary leads from
transformer to fixture leads using waterproof wire
connectors. (By Others). See wiring diagram.
JUNCTION BOX WITH INTEGRAL TRANSFORMER AND “B” CAP:
1. Pull primary branch circuit through transformer
T-housing. Attach ground from branch circuit
to screw in transformer T-housing.
WIRING DIAGRAM
120V 12V
Lamp
COM
GROUND
Transformer
COM
GROUND IN T-HOUSING
WIRING DIAGRAM
Junction Box/Stake w Transformer and B Cap
120V 12V
Fixture
COM
GROUND
Transformer
COM
GROUND IN T-HOUSING
WIRING DIAGRAM
Junction Box/Stake w Transformer and C Cap
2. Attach transformer T-housing to Power Pipe™
with (3) #8-32 round head Phillips stainless
steel screws at base of housing to secure to
Power Pipe™ with Phillips screwdriver.
2. Attach ground from branch circuit to screw in
transformer T-housing. Place transformer and
connectors into T-housing.
3. Attach C cap and transformer T-housing to Power
Pipe™ with (3) #8-32 round head Phillips stainless
steel screws at base of housing to secure to Power
Pipe™ with Phillips screwdriver.
WIRING DIAGRAM
120V 12V
Lamp
COM
GROUND
Transformer
COM
GROUND IN T-HOUSING
WIRING DIAGRAM
Junction Box/Stake w Transformer and B Cap
120V 12V
Fixture
COM
GROUND
Transformer
COM
GROUND IN T-HOUSING
WIRING DIAGRAM
Junction Box/Stake w Transformer and C Cap
1. Make watertight connections from primary
branch circuit to primary side of transformer
using waterproof wire connectors. (By Others).
Attach secondary leads from transformer to
low voltage cable using approved waterproof
wire connectors. (By Others).
JUNCTION BOX WITH INTEGRAL TRANSFORMER T-HOUSING WITH “C” CAP:
Failure to use waterproof wire connectors
will cause fixture to fail and VOID PRODUCT
WARRANTY.
Failure to use waterproof wire connectors
will cause fixture to fail and VOID PRODUCT
WARRANTY.
Box With Integral
12V or 12V or
With 'B' Cap
Power Pipe Junction Box Power Pipe Junction
Fixtures With 'C' Cap
Transformer For Remote
Box With Integral
Transformer With 'B' Cap
Power Pipe Junction
120V/230V/277V In 120V/230V/277V Out 120V/230V/277V In 12V Out 120V/230V/277V In 12V or 120V/230V/277V Out
Grade Grade
or UF CableConduit or UF CableConduit or UF CableConduit
Fixtures With 'C' Cap
Power Pipe Stake
Power Pipe Stake
With Integral Transformer With 'B' Cap
120V/230V/277V In
Transformer For Remote
With Integral
12V Out
12V or
12V or 120V/230V/277V Out
With 'B' Cap
Power Pipe Stake
Grade Grade
120V/230V/277V In
12V or
or UF CableConduit or UF CableConduit or UF CableConduit
120V/230V/277V In 120V/230V/277V In
12V Out
Power Pipe
Adjustable Stem
12V In
Grade
or UF CableConduit
RELEASED
12-13-16
REFERENCE NUMBER
INS001284
40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX 559.438.5900
www.bklighting.com • [email protected]
B-K LIGHTING
THIS DOCUMENT CONTAINS PROPRIETARY INFORMATION OF B-K LIGHTING, INC. AND ITS RECEIPT OR POSSESSION DOES NOT CONVEY ANY RIGHTS TO REPRODUCE, DISCLOSE ITS CONTENTS, OR TO MANUFACTURE, USE OR SELL ANYTHING IT MAY
DESCRIBE. REPRODUCTION, DISCLOSURE OR USE WITHOUT SPECIFIC WRITTEN AUTHORIZATION OF B-K LIGHTING, INC. IS STRICTLY FORBIDDEN.
IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE THESE INSTALLATION INSTRUCTIONS
TOOLS
REQUIRED:
By Others
• Product must be installed by a qualified person in a manner
consistent with its intended use and in compliance with the
National Electrical Code, Canadian Electrical Code, and all Local
and Provincial Codes.
• Follow product label information and instructions.
• Qualified Personnel must perform all servicing or relamping of
this product.
• Before wiring to power supply and during servicing or relamping,
turn off power at fuse or circuit breaker before service.
• The use of accessory equipment not recommended by the
manufacturer or installed contrary to instructions may cause an
unsafe condition. The use of damaged components may cause
an unsafe condition and void product warranty.
IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE ALL SAFETY
AND INSTALLATION INSTRUCTIONS
• Do not block light emanating from product in whole or part,
as this may cause an unsafe condition.
• Never operate the fixture with missing or damaged lens.
Lens must be cleaned on regular basis.
• Entire fixture may become extremely hot. Do not touch hot
lens or fixture body. Do not touch the lamp at any time. Use
a clean, dry, soft cloth to handle the lamp. Oil from skin may
damage the lamp and cause it to rupture.
• Replace lamp only with correct wattage and type of lamp
marked on fixture label.
• All gaskets, o-rings and sealing surfaces must be kept clean
during installation and service; failure to do this may cause an
unsafe condition and void product warranty.
INSTRUCTIONS PERTAINING TO
A RISK OF FIRE, OR INJURY TO
PERSONS IMPORTANT SAFETY
INSTRUCTIONS
Lighted lamp is HOT!
WARNING - To reduce the risk of FIRE OR INJURY TO PERSONS:
Turn off/unplug and allow to cool before replacing lamp.
Lamp gets HOT quickly! Contact only switch/plug when
turning on.
Do not touch hot lens, guard, or enclosure (see diagram/
picture).
Keep lamp away from materials that may burn.
Do no touch the lamp at any time. Use a soft cloth. Oil
from skin may damage lamp.
Do not operate the luminaire fitting with a missing or
damaged shield.
SAVE THESE INSTRUCTIONS
· Suitable for wet locations
IMPORTANT LISTINGS AND CERTIFICATIONS
Warning High Voltage
POWER PIPE™ SYSTEM
Power Pipe™ Stake and Adjustable Stem
Installation Instructions
GRADE
GRADE
Stability Flange™
PP Stake ‘S’
12" or
18"
2" Dia. PVC
Housing
Specify Fixture
Separately
5/64” Allen Wrench
Waterproof Wire Connectors
Phillips Screwdriver
Please refer to the low voltage
design guide at www.bklighting.
com/lvguide before installation for
proper wire selection.
Grade Level Label
Proper soil preparation is
recommended before installation. See
the DIG-IT guide at www.bklighting.
com/dig-it for more information.
40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX 559.438.5900
www.bklighting.com • [email protected]
B-K LIGHTING
IMPORTANT SAFETY INFORMATION LISTED ON REVERSE
READ, FOLLOW, AND SAVE ALL SAFETY AND INSTALLATION INSTRUCTIONS
RELEASED
12-13-16
REFERENCE NUMBER
INS001284
POWER PIPE™ SYSTEM
Power Pipe™ Stake and Adjustable Stem
Installation Instructions
1. Make watertight connections from remote 12V
transformer to fixture leads using waterproof
wire connectors. (By Others)
STAKE WITH “B” CAP:
2. Route the necessary UL approved under
ground branch circuit or low voltage wiring
to Power Pipe™ necessary for appropriate
installation. Leave enough length to make
connections to fixture leads.
3. Back fill hole with soil and/or prep for concrete.
4. Pull branch circuit or low voltage wiring
necessary for appropriate installation (By
Others).
1. Excavate trench according to designed lighting plan.
Dig hole a minimum of 24” deep and 10” wide
to accommodate Power Pipe™ at desired fixture
locations. Do not cut PVC.
INSTALLATION OF POWER PIPE™ STAKE
Finished grade
Pea gravel or sand
Finished grade
Finished grade
Stability Flange Pea gravel or sand
Finished grade
Pea gravel
or sand
Above Ground
Installation
Pea gravel
or sand
Concrete
Pea gravel
or sand
Pea gravel
or sand
Pea gravel
or sand
Concrete
Below Ground
Installation
Pea gravel
or sand
Finished grade
Pea gravel or sand
Finished grade
Finished grade
Stability Flange Pea gravel or sand
Finished grade
Pea gravel
or sand
Above Ground
Installation
Pea gravel
or sand
Concrete
Pea gravel
or sand
Pea gravel
or sand
Pea gravel
or sand
Concrete
Below Ground
Installation
Pea gravel
or sand
Finished grade
Pea gravel or sand
Finished grade
Finished grade
Stability Flange Pea gravel or sand
Finished grade
Pea gravel
or sand
Above Ground
Installation
Pea gravel
or sand
Concrete
Pea gravel
or sand
Pea gravel
or sand
Pea gravel
or sand
Concrete
Below Ground
Installation
Pea gravel
or sand
2. Attach B cap to Power Pipe™ with (3) #8-32
round head Phillips stainless steel screws at
base to secure to Power Pipe™ with Phillips
screwdriver.
120V 12V
Fixture
COM
Remote
Transformer
COM
120V 12V
Fixture
COM
GROUND
WIRING DIAGRAM
Integral
Transformer
COM
GROUND IN HOUSING
WIRING DIAGRAM
GRADE
TRANSFORMER HOUSING MUST BE INSTALLED ABOVE GRADE. POWER PIPE™ IS LABELED AT GRADE LEVEL.
TRANSFORMER HOUSING INSTALLED BELOW GRADE WILL VOID WARRANTY
Soil Prep
Conduit
trench
B. Dig hole 10” wide and 24” deep.
Conduit
Trench
Excavated
for Housing
C. Prep soil according to DIG-IT Guide.A. Determine Soil Type by referencing DIG-IT Guide.
Prep soil according to DIG-IT Guide.
Failure to use waterproof wire connectors
will cause fixture to fail and VOID PRODUCT
WARRANTY.
40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX 559.438.5900
www.bklighting.com • [email protected]
B-K LIGHTING
IMPORTANT SAFETY INFORMATION LISTED ON REVERSE
READ, FOLLOW, AND SAVE ALL SAFETY AND INSTALLATION INSTRUCTIONS
RELEASED
12-13-16
REFERENCE NUMBER
INS001284
PROJECT:
TYPE:
POWER PIPE™ SYSTEM
Power Pipe™ Stake and Adjustable Stem
Installation Instructions
WIRING DIAGRAM 4. Place transformer and connectors into
T-housing. Attach B cap to T-housing with
(3) #8-32 stainless steel set screws using 5/64”
Allen wrench.
3. Make watertight connections from primary
branch circuit to primary side of transformer
using waterproof wire connectors. (By Others).
Attach secondary leads from transformer to
fixture leads using waterproof wire connectors.
(By Others). See wiring diagram.
STAKE WITH INTEGRAL TRANSFORMER AND “B” CAP:
1. Pull primary branch circuit through
transformer T-housing. Attach ground
from branch circuit to screw in transformer
T-housing.
WIRING DIAGRAM
120V 12V
Lamp
COM
GROUND
Transformer
COM
GROUND IN T-HOUSING
WIRING DIAGRAM
Junction Box/Stake w Transformer and B Cap
120V 12V
Fixture
COM
GROUND
Transformer
COM
GROUND IN T-HOUSING
WIRING DIAGRAM
Junction Box/Stake w Transformer and C Cap
2. Attach transformer T-housing to Power Pipe™
with (3) #8-32 round head Phillips stainless
steel screws at base of housing to secure to
Power Pipe™ with Phillips screwdriver.
GRADE
2. Attach ground from branch circuit to screw in
transformer T-housing. Place transformer and
connectors into T-housing.
3. Attach C cap and transformer T-housing to
Power Pipe™ with (3) #8-32 round head Phillips
stainless steel screws at base of housing to
secure to Power Pipe™ with Phillips screwdriver.
WIRING DIAGRAM
120V 12V
Lamp
COM
GROUND
Transformer
COM
GROUND IN T-HOUSING
WIRING DIAGRAM
Junction Box/Stake w Transformer and B Cap
120V 12V
Fixture
COM
GROUND
Transformer
COM
GROUND IN T-HOUSING
WIRING DIAGRAM
Junction Box/Stake w Transformer and C Cap
1. Make watertight connections from primary
branch circuit to primary side of transformer
using waterproof wire connectors. (By Others).
Attach secondary leads from transformer to low
voltage cable using waterproof wire connectors.
(By Others).
STAKE WITH INTEGRAL TRANSFORMER T-HOUSING WITH “C” CAP:
Failure to use waterproof wire connectors
will cause fixture to fail and VOID PRODUCT
WARRANTY.
Failure to use waterproof wire connectors
will cause fixture to fail and VOID PRODUCT
WARRANTY.
40429 Brickyard Drive • Madera, CA 93636 • USA
559.438.5800 • FAX 559.438.5900
www.bklighting.com • [email protected]
B-K LIGHTING
IMPORTANT SAFETY INFORMATION LISTED ON REVERSE
READ, FOLLOW, AND SAVE ALL SAFETY AND INSTALLATION INSTRUCTIONS
RELEASED
12-13-16
REFERENCE NUMBER
INS001284
PROJECT:
TYPE:
POWER PIPE™ SYSTEM
Power Pipe™ Stake and Adjustable Stem
Installation Instructions
GRADE
2. Insert additional wires and connectors into
Power Pipe. Place fixture on Power Pipe™.
3. Tighten three (3) #8-32 round head Phillips
stainless steel screws at base to secure to Power
Pipe™ with Phillips screwdriver.
Pea gravel or sand
Finished grade
Pea gravel or sand
Concrete or Soil
Finished grade
LINE 12V
FIXTURE
COM
Remote
Transformer
(by others)
COM
Finished grade Optional
Stability Flange
1. Make watertight connections from
remote transformer to fixture leads using
waterproof wire connectors. (By Others).
Adjustable stem includes 60” of additional
18/2 direct burial low voltage cable.
4. Slide stem up or down to desired height. Delrin
bushing holds stem in position. Tighten three (3)
#8-32 stainless steel set screws using a 5/64” Allen
wrench to lock mounting height in place. Unused
stem length remains hidden inside Power Pipe™
to accommodate future landscape growth.
Pea gravel or sand
Finished grade
Pea gravel or sand
Concrete or Soil
Finished grade
LINE 12V
FIXTURE
COM
Remote
Transformer
(by others)
COM
Finished grade Optional
Stability Flange
ADJUSTABLE STEM FIXTURE INSTALLATION
For Adjustable Stem Only
Failure to use waterproof wire connectors
will cause fixture to fail and VOID PRODUCT
WARRANTY.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7

B-K lighting Power Pipe Installation guide

Brand
B-K lighting
Model
Power Pipe
Type
Installation guide
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents