Maxell FL710M User guide

Brand: Maxell

Model: FL710M

Category: Projector mounts

Type: User guide

Model

Thank you for purchasing this lens unit for Projectors.

Prior to use, read the user manuals of both this product and your projector thoroughly and follow their instructions.

After reading the User's Manual, keep it in a safe place for future use.

This product consists of the lens mount brackets and option lens (FL-710) for Projectors.

Notice

●Thecontentofthismanualissubjecttochangewithoutnotice;thisincludestheproductspecications.

●Maxellwillnotbeliableforanyinjuriesordamageduetoimproperuseorapplicationoutsidetheintendedscope.

Projector Lens Unit

FL-710 Projector Lens Unit

Symbols

This manual uses the following symbols to help you and any helpers use the product safely and according to

instructions, in order to prevent any injury or property damage. Please read thoroughly so you understand them and

use the product accordingly.

Warning

Ignoring this symbol and handling the product incorrectly may result in serious injury or

death.

Caution

Ignoring this symbol and handling the product incorrectly may result in injury and/or

property damage.

Table of Contents

Symbols .................................................. 1

Overview.................................................2

Important Considerations for Installation

...2

Periodic Inspection .................................3

Checking the Contents of Packaging .....4

Mounting the Brackets ............................7

When Using on a Tabletop ...................10

When Using the Ceiling Mount Bracket

(HAS-404U) ..........................................10

This symbol indicates prohibited actions.

The description after this symbol indicates actions that are not allowed to be performed.

This symbol indicates mandatory actions.

The description after this symbol indicates actions that must always be performed.

User’s Manual

FL-710

Special skills are necessary for installing this product. Be sure to ask the sales outlet or a service company (See the

User's Manual of your Projector) to perform the installation job.

Pay particular attention to the following points when mounting a projector on the ceiling.

1. Before performing the mounting design and construction work, verify that the weight of the projector and ceiling

mountwith6-axisadjustment(HAS-404U)canbefullysupported.

To protect itself, the projector has a temperature sensor that turns off the power if its internal temperature rises

abnormally.

Follow the instructions below to prevent the temperature from rising abnormally.

(1) Do not install in locations where the temperature is outside the operating temperature range indicated in the

projector's User's Manual.

(2)Periodicallycleantheairlterontheinsideoftheairintake.Seeyourprojector'sUser'sManualforinformation

on cleaning frequency and method.

(3) If installed in a location with lots of dust, the cleaning mentioned in (2) has to be done more frequently, so

mount in a location where it can easily be cleaned.

(4)Tofacilitateventilationfromtheexhaustoutlet,allowforatleast50cmofspacearoundtheprojector.

(5)Donotinstallinlocationsthataresubjecttosuddenchangesintemperature,suchasnearanairconditioner,or

wherethetemperatureexceedstheoperatingtemperatureindicatedintheprojector'sUser'sManual.

If r

esidue from tobacco gets on the optics of the projector, it deteriorates its projection performance. Do not install

in a l

ocationsubjecttoexcessivetobaccosmoke.

he remote control may not function properly if the remote control signal receiver on the projector is subject to

stronglight,suchasdirectsunlight,oruorescentlightingatpointblankrange.Installsothereceiverisnotsubject

to direct light.

Important Considerations for Installation

Overview

This product includes the lens mount brackets and option lens (FL-710) for Projectors.

FL-710 FL-710

Warning

To the customer:

■Thecustomershouldneverattempttoperformtheinstallationwork.Pleasehavethesalesoutlet

or service company perform the installation. Please be warned that we shall bear no responsibility

whatsoever for any accidents or injuries that occur from improper installation or handling.

■Installataheightwherepeoplewillnothittheirheadontheprojector.Iftheprojectorisinstalledata

lowposition,beextremelycarefulwhenusing.

■

Afterinstallation,donothangdownfromtheprojectororceilingmountwith6-axisadjustment

(HAS-

404U).

An injury or damage could occur due to the projector falling, the bracket becoming bent, or

other breakage.

■

Donotinstallinlocations exposedtolargeamountsofhumidity,dust,orcigarettesmoke,locations

exposedtooilsmokeorsteam,orlocationswheresaltdamagecanoccur.

■

Donotinstallinlocationsexposedtolargeamountsofvibrations.

■

Once installation is completed, store this manual and the accessories in a safe location.

■

Be careful when handling the small parts. They could be ingested by children or pets. If a part is

ingested, seek medical attention immediately.

To the installer:

■InstallthisproductproperlyaccordingtothisUser'sManual.Installallthescrewsandhardwareas

indicated.

■

Before performing the mounting design and construction work, verify that the weight of the projector

andceilingmountwith6-axisadjustment(HAS-404U)canbefullysupported.

■

Nevermodifytheceilingmountwith6-axisadjustment.

(The strength can no longer be guaranteed

onceitismodied.)

■Afterperformingthemountingadjustment,checkthatthescrewsaresecuredinplaceatthe

speciedforce.Becarefulthatnoscrewsarelooseorover-tightened.

■Donotusescrewlockingadhesive,lubricants,oils,orothersolventsontheanchoringsectionofthe

projector ceiling mount because the case could break or the projector could fall, resulting in an injury

or other accident.

■Installandroutethepowerandothercablesthroughthedesignatedlocations,andbecarefulthat

they are not damaged.

■Carefullyreadtheprojector'sUser'sManualpriortoperforminganyinstallationwork,andinstall

correctly by following all safety precautions.

■Priortoinstallation,makesuretheprojectorisOFFandunplugthepowercord.

■Donotinstallinlocations whereoilisused.Oilcanadhereduetooilsmokeorothersubstances,

resultinginabreakdown,re,orelectricalshock.Itcanalsocausedeteriorationoftheplastic,which

can result in an injury due to parts falling from the ceiling or elevated locations.

Periodic Inspection

As a general guideline, inspect the points below once per year in the same way as the set unit.

1. Check that the screws of the ceiling mount brackets and adjustment locations are not loose.

2. Inspect that the ceiling mount brackets, adjustment parts, set unit, and other parts are not broken or damaged.

FL-710

Makesurethefollowingitemsarepackedinsidethebox.Ifsomethingshouldbemissing,contactthesalesoutletright

away.

Accessories Packaged with FL-710 Lens Unit

Checking the Contents of Packaging

Lens mount bracket

Lens Mount bracket

User's Manual

(this manual)

Option lens FL-710

FL-710 FL-710

Code Part Name Qty. Appearance Code Part Name Qty. Appearance

(A) Mount bracket A 1

(D) M4×10 screws 2

(B) Mount bracket B 1 (E) Collar 2

(C)

M6×16

Hex-headscrew

4 (F) Hexkey 1

Code Part Name Qty. Appearance Code Part Name Qty. Appearance

(H)

Option lens

(FL-710)

1 (

)

Option Lens

User's Manual

Names of parts are indicated with codes in the table below and on subsequent pages.

●AccessoriesPackagedwithLensMountBracket

●AccessoriesPackagedwithFL-710

FL-710

1.RemovetheoptionlensFL-710(H)fromthebox.

For details on operating the option lens FL-710 (H), refer to the Option Lens User's Manual (I).

2.Removethemountbrackets(A)andaccessorypartsfromthebox.

Removing the Packaged Items

Option Lens User's Manual (I)

FL-710 (H)

Mount bracket A

Accessory parts

FL-710 FL-710

1. Attach the option lens FL-710 (H) to the projector.

(For details, refer to the Option Lens User's Manual (I).

2. Provide a worktable so that no force is applied to the option lens FL-710 (H).

Put cushioning materials on top of the worktable, and place the projector upside-down on the cushioning before

starting work.

Put the option lens FL-710 (H) in a location away from the worktable.

3. Use the two M4X10 screws (D) to attach the mount bracket (B) to the option lens FL-710 (H).

Tightening torque: 0.98 N·m (10 kgf·cm)

4. Remove the two adjusters from the projector. 5.Insertthetwocollars(E)intotheremovedadjusters,

and mount to the projector.

Mounting the Brackets

Option lens FL-710 (H)

Mount bracket (B)

Note the direction of

the arrow on mount

bracket (B).

M4x10screws(D)(2locations)

Projector

Worktable

Adjuster

Option lens FL-710 (H)

Warning

■Beextremelycarefulwhenperformingthemountingwork.An injury or other

accident can occur if the projector falls.

Collar (E)

Adjuster Adjuster

FL-710

6.Usethehexkey(F)toloosenthescrew(Q)untilitstops.

7. Mount the mount bracket (A) to the mount bracket (B).

Screw (Q)

(Hole)

Mount bracket (B)

Mount bracket (A)

Insertion direction

Protrusion

FL-710 FL-710

8. Move the screw (Q) of mount bracket (A) up and down as well as left and right to insert it into the protrusion of

mount bracket (B).

It can be easier to insert when viewing from the top (hole) of mount bracket (A).

Screw (Q)

Mount Bracket (B)

Mount bracket (B)

Side view of engaged section

Screw (Q) Mount bracket (A)

(Hole)

Protrusion

Insert the protrusion of

mount bracket (B) into this

section.

FL-710

UsethefourM6×16hex-headscrews(C)toattachthemountbracket(A)totheprojector.

TightentheM6×16hex-headscrews(C)intheorder





. Tightening torque: 1.96N·m (20kgf·cm)

When Using on a Tabletop

9. Return the projector to its original state.

10. Use the vertical and horizontal shift adjustment to adjust to the proper screen position.

11. Firmly tighten the screw (Q) until it is locked in place.

Warning

■ Whenever adjusting the vertical and horizontal shift, be sure to always loosen

the screw (Q). Adjusting the vertical and horizontal shift without loosening the

screw (Q) can damage the product.

■ After adjusting the vertical and horizontalshift,rmlyretightenthescrew(Q).

1.UsethefourM6×16hex-headscrews(C)tomountthebracket(B)oftheceilingmountbracket(HAS-404U)tothe

projectorandmountbracket(A).TightentheM6×16hex-headscrews(C)intheorder





2. For the mounting work after this procedure, refer to the ceiling mount bracket (HAS-404U) user's manual.

3. Use the vertical and horizontal shift adjustment to adjust to the proper screen position.

4. Firmly tighten the screw (Q) until it is locked in place.

When Using the Ceiling Mount Bracket (HAS-404U)

M6×16

Hex-headscrew(C)

HAS-404U

Bracket (B)

Mounting completed

M6×16

Hex-headscrew(C)









Screw (Q)

M6×16hex-headscrews(C)









Screw (Q)

Maxell FL710M User guide

Brand: Maxell

Model: FL710M

Category: Projector mounts

Type: User guide

Download PDF

report

Maxell FL710M User guide

Maxell FL710M User guide

Related papers

Other documents