Maxell FL710M User guide

Maxell
Brand
Maxell
Model
FL710M
Category
Projector mounts
Type
User guide

This manual is also suitable for

1
Model
Thank you for purchasing this lens unit for Projectors.
Prior to use, read the user manuals of both this product and your projector thoroughly and follow their instructions.
After reading the User's Manual, keep it in a safe place for future use.
This product consists of the lens mount brackets and option lens (FL-710) for Projectors.
Notice
●Thecontentofthismanualissubjecttochangewithoutnotice;thisincludestheproductspecications.
●Maxellwillnotbeliableforanyinjuriesordamageduetoimproperuseorapplicationoutsidetheintendedscope.
Projector Lens Unit
FL-720 Projector Lens Unit
Symbols
This manual uses the following symbols to help you and any helpers use the product safely and according to
instructions, in order to prevent any injury or property damage. Please read thoroughly so you understand them and
use the product accordingly.
Warning
Ignoring this symbol and handling the product incorrectly may result in serious injury or
death.
Caution
Ignoring this symbol and handling the product incorrectly may result in injury and/or
property damage.
Table of Contents
Symbols .................................................. 1
Overview.................................................2
Important Considerations for Installation
...2
Periodic Inspection .................................3
Checking the Contents of Packaging .....4
Mounting the Brackets ............................7
When Using on a Tabletop ...................10
When Using the Ceiling Mount Bracket
(HAS-404U) ..........................................10
This symbol indicates prohibited actions.
The description after this symbol indicates actions that are not allowed to be performed.
This symbol indicates mandatory actions.
The description after this symbol indicates actions that must always be performed.
User’s Manual
2
FL-720
Special skills are necessary for installing this product. Be sure to ask the sales outlet or a service company (See the
User's Manual of your Projector) to perform the installation job.
Pay particular attention to the following points when mounting a projector on the ceiling.
1. Before performing the mounting design and construction work, verify that the weight of the projector and ceiling
mountwith6-axisadjustment(HAS-404U)canbefullysupported.
2.
To protect itself, the projector has a temperature sensor that turns off the power if its internal temperature rises
abnormally.
Follow the instructions below to prevent the temperature from rising abnormally.
(1) Do not install in locations where the temperature is outside the operating temperature range indicated in the
projector's User's Manual.
(2)Periodicallycleantheairlterontheinsideoftheairintake.Seeyourprojector'sUser'sManualforinformation
on cleaning frequency and method.
(3) If installed in a location with lots of dust, the cleaning mentioned in (2) has to be done more frequently, so
mount in a location where it can easily be cleaned.
(4)Tofacilitateventilationfromtheexhaustoutlet,allowforatleast50cmofspacearoundtheprojector.
(5)Donotinstallinlocationsthataresubjecttosuddenchangesintemperature,suchasnearanairconditioner,or
wherethetemperatureexceedstheoperatingtemperatureindicatedintheprojector'sUser'sManual.
3.
If r
esidue from tobacco gets on the optics of the projector, it deteriorates its projection performance. Do not install
in a l
ocationsubjecttoexcessivetobaccosmoke.
4.
T
he remote control may not function properly if the remote control signal receiver on the projector is subject to
stronglight,suchasdirectsunlight,oruorescentlightingatpointblankrange.Installsothereceiverisnotsubject
to direct light.
Important Considerations for Installation
Overview
This product includes the lens mount brackets and option lens (FL-710) for Projectors.
3
FL-720 FL-720
Warning
To the customer:
■Thecustomershouldneverattempttoperformtheinstallationwork.Pleasehavethesalesoutlet
or service company perform the installation. Please be warned that we shall bear no responsibility
whatsoever for any accidents or injuries that occur from improper installation or handling.
■Installataheightwherepeoplewillnothittheirheadontheprojector.Iftheprojectorisinstalledata
lowposition,beextremelycarefulwhenusing.
■
Afterinstallation,donothang downfromtheprojectororceilingmountwith6-axisadjustment
(HAS-404U). An injury or damage could occur due to the projector falling, the bracket becoming bent,
or other breakage.
■
Donotinstallinlocations exposedtolargeamountsofhumidity,dust,orcigarettesmoke,locations
exposedtooilsmokeorsteam,orlocationswheresaltdamagecanoccur.
■
Donotinstallinlocationsexposedtolargeamountsofvibrations.
■
Once installation is completed, store this manual and the accessories in a safe location.
■
Be careful when handling the small parts. They could be ingested by children or pets. If a part is
ingested, seek medical attention immediately.
To the installer:
■InstallthisproductproperlyaccordingtothisUser'sManual.Installallthescrewsandhardwareas
indicated.
■
Before performing the mounting design and construction work, verify that the weight of the projector
andceilingmountwith6-axisadjustment(HAS-404U)canbefullysupported.
■
Nevermodifytheceilingmountwith6-axisadjustment.
(The strength can no longer be guaranteed
onceitismodied.)
■Afterperformingthemountingadjustment,checkthatthescrewsaresecuredinplaceatthe
speciedforce.Becarefulthatnoscrewsarelooseorover-tightened.
■Donotusescrewlockingadhesive,lubricants,oils,orothersolventsontheanchoringsectionofthe
projector ceiling mount because the case could break or the projector could fall, resulting in an injury
or other accident.
■Installandroutethepowerandothercablesthroughthedesignatedlocations,andbecarefulthat
they are not damaged.
■Carefullyreadtheprojector'sUser'sManualpriortoperforminganyinstallationwork,andinstall
correctly by following all safety precautions.
■Priortoinstallation,makesuretheprojectorisOFFandunplugthepowercord.
■Donotinstallinlocations whereoilisused.Oilcanadhereduetooilsmokeorothersubstances,
resultinginabreakdown,re,orelectricalshock.Itcanalsocausedeteriorationoftheplastic,which
can result in an injury due to parts falling from the ceiling or elevated locations.
Periodic Inspection
As a general guideline, inspect the points below once per year in the same way as the set unit.
1. Check that the screws of the ceiling mount brackets and adjustment locations are not loose.
2. Inspect that the ceiling mount brackets, adjustment parts, set unit, and other parts are not broken or damaged.
4
FL-720
Makesurethefollowingitemsarepackedinsidethebox.Ifsomethingshouldbemissing,contactthesalesoutletright
away.
Accessories Packaged with FL-720 Lens Unit
Checking the Contents of Packaging
Lens mount bracket
Lens Mount bracket
User's Manual
(this manual)
Option lens FL-710
5
FL-720 FL-720
Code Part Name Qty. Appearance Code Part Name Qty. Appearance
(A) Mount bracket A 1
(D) M4×10 screws 2
(B) Mount bracket B 1 (E) Collar 2
(C)
M6×16
Hex-headscrew
4 (F) Hexkey 1
Code Part Name Qty. Appearance Code Part Name Qty. Appearance
(H)
Option lens
(FL-710)
1 (
I
)
Option Lens
User's Manual
1
Names of parts are indicated with codes in the table below and on subsequent pages.
●AccessoriesPackagedwithLensMountBracket
●AccessoriesPackagedwithFL-720
6
FL-720
1.RemovetheoptionlensFL-710(H)fromthebox.
For details on operating the option lens FL-710 (H), refer to the Option Lens User's Manual (I).
2.Removethemountbrackets(A)andaccessorypartsfromthebox.
Removing the Packaged Items
Option Lens User's Manual (I)
FL-710 (H)
Mount bracket A
Accessory parts
7
FL-720 FL-720
1. Attach the option lens FL-710 (H) to the projector.
(For details, refer to the Option Lens User's Manual (I).
2. Provide a worktable so that no force is applied to the option lens FL-710 (H).
Put cushioning materials on top of the worktable, and place the projector upside-down on the cushioning before
starting work.
Put the option lens FL-710 (H) in a location away from the worktable.
3. Use the two M4X10 screws (D) to attach the mount bracket (B) to the option lens FL-710 (H).
Tightening torque: 0.98 N·m (10 kgf·cm)
4. Remove the two adjusters from the projector. 5.Insertthetwocollars(E)intotheremovedadjusters,
and mount to the projector.
Mounting the Brackets
Option lens FL-710 (H)
Mount bracket (B)
Note the direction of
the arrow on mount
bracket (B).
M4x10screws(D)(2locations)
Warning
■Beextremelycarefulwhenperformingthemountingwork.An injury or other
accident can occur if the projector falls.
Adjuster
Option lens FL-710 (H)
Projector
Worktable
Adjuster Adjuster
Collar (E)
8
FL-720
6.Usethehexkey(F)toloosenthescrew(Q)untilitstops.
7. Mount the mount bracket (A) to the mount bracket (B).
Screw (Q)
Screw (Q)
(Hole)
Mount bracket (B)
Mount bracket (A)
Insertion direction
Protrusion
9
FL-720 FL-720
8. Move the screw (Q) of mount bracket (A) up and down as well as left and right to insert it into the protrusion of
mount bracket (B).
It can be easier to insert when viewing from the top (hole) of mount bracket (A).
Screw (Q)
Mount Bracket (B)
Mount bracket (B)
Side view of engaged section
Screw (Q) Mount bracket (A)
(Hole)
Protrusion
Insert the protrusion of
mount bracket (B) into this
section.
10
FL-720
UsethefourM6×16hex-headscrews(C)toattachthemountbracket(A)totheprojector.
TightentheM6×16hex-headscrews(C)intheorder
to
. Tightening torque: 1.96N·m (20kgf·cm)
When Using on a Tabletop
9. Return the projector to its original state.
10. Use the vertical and horizontal shift adjustment to adjust to the proper screen position.
11. Firmly tighten the screw (Q) until it is locked in place.
Warning
■ Whenever adjusting the vertical and horizontal shift, be sure to always loosen
the screw (Q). Adjusting the vertical and horizontal shift without loosening the
screw (Q) can damage the product.
■ After adjusting the vertical and horizontalshift,rmlyretightenthescrew(Q).
1.UsethefourM6×16hex-headscrews(C)tomountthebracket(B)oftheceilingmountbracket(HAS-404U)tothe
projectorandmountbracket(A).TightentheM6×16hex-headscrews(C)intheorder
to
.
2. For the mounting work after this procedure, refer to the ceiling mount bracket (HAS-404U) user's manual.
3. Use the vertical and horizontal shift adjustment to adjust to the proper screen position.
4. Firmly tighten the screw (Q) until it is locked in place.
When Using the Ceiling Mount Bracket (HAS-404U)
Mounting completed
M6×16
Hex-headscrew(C)
HAS-404U
Bracket (B)
M6×16
Hex-headscrew(C)
Screw (Q)
M6×16hex-headscrews(C)
M6×16hex-headscrews(C)
Screw (Q)
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10

Maxell FL710M User guide

Maxell
Brand
Maxell
Model
FL710M
Category
Projector mounts
Type
User guide
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents