Hitachi FL920 User guide

Category
Projector mounts
Type
User guide
ENGLISH
1
Model
Thank you for purchasing this lens unit for HITACHI projectors.
Prior to use, read the user manuals of both this product and your projector thoroughly and follow their instructions.
After reading the User's Manual, keep it in a safe place for future use.
This product consists of the lens mount brackets and option lens (FL-900) for HITACHI projectors.
Notice
●Thecontentofthismanualissubjecttochangewithoutnotice;thisincludestheproductspecications.
●HITACHIwillnotbeliableforanyinjuriesordamageduetoimproperuseorapplicationoutsidetheintendedscope.
Projector Lens Unit
FL-920 Projector Lens Unit Users Manual
Symbols
This manual uses the following symbols to help you and any helpers use the product safely and according to
instructions, in order to prevent any injury or property damage. Please read thoroughly so you understand them and
use the product accordingly.
Warning
Ignoring this symbol and handling the product incorrectly may result in serious injury or
death.
Caution
Ignoring this symbol and handling the product incorrectly may result in injury and/or
property damage.
Table of Contents
Symbols ..................................................1
Overview.................................................2
Important Considerations for Installation
...2
Periodic Inspection .................................3
Checking the Contents of Packaging .....4
Mounting the Brackets ............................7
When Using on a Tabletop ...................10
When Using the Ceiling Mount Bracket
(HAS-404U) ..........................................10
This symbol indicates prohibited actions.
The description after this symbol indicates actions that are not allowed to be performed.
This symbol indicates mandatory actions.
The description after this symbol indicates actions that must always be performed.
01 FL-920_DD2_LensUnit_Eng_conv.indd 1 2016/01/05 21:22:32
2
Special skills are necessary for installing this product. Be sure to ask the sales outlet or a service company (See the
User's Manual of your HITACHI projector) to perform the installation job.
Pay particular attention to the following points when mounting a projector on the ceiling.
1. Before performing the mounting design and construction work, verify that the weight of the projector and ceiling
mount with 6-axis adjustment (HAS-404U) can be fully supported.
2.
To protect itself, the projector has a temperature sensor that turns off the power if its internal temperature rises
abnormally.
Follow the instructions below to prevent the temperature from rising abnormally.
(1) Do not install in locations where the temperature is outside the operating temperature range indicated in the
projector's User's Manual.
(2) Avoid placing the projector in smoky, humid or dusty place.
(3) To facilitate ventilation from the exhaust outlet, allow for at least 50 cm of space around the projector.
(4) Do not install in locations that are subject to sudden changes in temperature, such as near an air conditioner, or
where the temperature exceeds the operating temperature indicated in the projector's User's Manual.
3.
If r
esidue from tobacco gets on the optics of the projector, it deteriorates its projection performance. Do not install
in a l
ocation subject to excessive tobacco smoke.
4.
T
he remote control may not function properly if the remote control signal receiver on the projector is subject to
stronglight,suchasdirectsunlight,oruorescentlightingatpointblankrange.Installsothereceiverisnotsubject
to direct light.
Important Considerations for Installation
Overview
This product includes the lens mount brackets and option lens (FL-900) for HITACHI projectors.
3
Warning
To the customer:
T h e customershouldneverattempttoperform theinstallation work.Please havethe salesoutlet
or service company perform the installation. Please be warned that we shall bear no responsibility
whatsoever for any accidents or injuries that occur from improper installation or handling.
■Installataheightwherepeoplewillnothittheirheadontheprojector.Iftheprojectorisinstalledata
low position, be extremely careful when using.
After installation, do not hang down from the projector or ceiling mount with 6-axis adjustment
(HAS-
404U).
An injury or damage could occur due to the projector falling, the bracket becoming bent, or
other breakage.
Do not install in locations exposed to large amounts of humidity, dust, or cigarette smoke, locations
exposed to oil smoke or steam, or locations where salt damage can occur.
Do not install in locations exposed to large amounts of vibrations.
Once installation is completed, store this manual and the accessories in a safe location.
Be careful when handling the small parts. They could be ingested by children or pets. If a part is
ingested, seek medical attention immediately.
To the installer:
■InstallthisproductproperlyaccordingtothisUser'sManual.Installallthescrewsandhardwareas
indicated.
■
Before performing the mounting design and construction work, verify that the weight of the projector
and ceiling mount with 6-axis adjustment (HAS-404U) can be fully supported.
■
Never modify the ceiling mount with 6-axis adjustment.
(The strength can no longer be guaranteed
onceitismodied.)
■After performing the mounting adjustment, check that the screws are secured in place at the
speciedforce.Becarefulthatnoscrewsarelooseorover-tightened.
■Donotusescrewlockingadhesive,lubricants,oils,orothersolventsontheanchoringsectionofthe
projector ceiling mount because the case could break or the projector could fall, resulting in an injury
or other accident.
■Installandroute thepower andothercablesthroughthedesignatedlocations, andbe carefulthat
they are not damaged.
■Carefully read theprojector's User's Manualprior toperformingany installationwork, and install
correctly by following all safety precautions.
■Priortoinstallation,makesuretheprojectorisOFFandunplugthepowercord.
■Donotinstallinlocations whereoil isused. Oilcanadheredueto oilsmoke orothersubstances,
resultinginabreakdown,re,orelectricalshock.Itcanalsocausedeteriorationoftheplastic,which
can result in an injury due to parts falling from the ceiling or elevated locations.
Periodic Inspection
As a general guideline, inspect the points below once per year in the same way as the set unit.
1. Check that the screws of the ceiling mount brackets and adjustment locations are not loose.
2. Inspect that the ceiling mount brackets, adjustment parts, set unit, and other parts are not broken or damaged.
01 FL-920_DD2_LensUnit_Eng_conv.indd 2 2016/01/05 21:22:32
ENGLISH
2
Special skills are necessary for installing this product. Be sure to ask the sales outlet or a service company (See the
User's Manual of your HITACHI projector) to perform the installation job.
Pay particular attention to the following points when mounting a projector on the ceiling.
1. Before performing the mounting design and construction work, verify that the weight of the projector and ceiling
mount with 6-axis adjustment (HAS-404U) can be fully supported.
2.
To protect itself, the projector has a temperature sensor that turns off the power if its internal temperature rises
abnormally.
Follow the instructions below to prevent the temperature from rising abnormally.
(1) Do not install in locations where the temperature is outside the operating temperature range indicated in the
projector's User's Manual.
(2) Avoid placing the projector in smoky, humid or dusty place.
(3) To facilitate ventilation from the exhaust outlet, allow for at least 50 cm of space around the projector.
(4) Do not install in locations that are subject to sudden changes in temperature, such as near an air conditioner, or
where the temperature exceeds the operating temperature indicated in the projector's User's Manual.
3.
If r
esidue from tobacco gets on the optics of the projector, it deteriorates its projection performance. Do not install
in a l
ocation subject to excessive tobacco smoke.
4.
T
he remote control may not function properly if the remote control signal receiver on the projector is subject to
stronglight,suchasdirectsunlight,oruorescentlightingatpointblankrange.Installsothereceiverisnotsubject
to direct light.
Important Considerations for Installation
Overview
This product includes the lens mount brackets and option lens (FL-900) for HITACHI projectors.
3
Warning
To the customer:
T h e customershouldneverattempttoperform theinstallation work.Please havethe salesoutlet
or service company perform the installation. Please be warned that we shall bear no responsibility
whatsoever for any accidents or injuries that occur from improper installation or handling.
■Installataheightwherepeoplewillnothittheirheadontheprojector.Iftheprojectorisinstalledata
low position, be extremely careful when using.
After installation, do not hang down from the projector or ceiling mount with 6-axis adjustment
(HAS-
404U).
An injury or damage could occur due to the projector falling, the bracket becoming bent, or
other breakage.
Do not install in locations exposed to large amounts of humidity, dust, or cigarette smoke, locations
exposed to oil smoke or steam, or locations where salt damage can occur.
Do not install in locations exposed to large amounts of vibrations.
Once installation is completed, store this manual and the accessories in a safe location.
Be careful when handling the small parts. They could be ingested by children or pets. If a part is
ingested, seek medical attention immediately.
To the installer:
■InstallthisproductproperlyaccordingtothisUser'sManual.Installallthescrewsandhardwareas
indicated.
■
Before performing the mounting design and construction work, verify that the weight of the projector
and ceiling mount with 6-axis adjustment (HAS-404U) can be fully supported.
■
Never modify the ceiling mount with 6-axis adjustment.
(The strength can no longer be guaranteed
onceitismodied.)
■After performing the mounting adjustment, check that the screws are secured in place at the
speciedforce.Becarefulthatnoscrewsarelooseorover-tightened.
■Donotusescrewlockingadhesive,lubricants,oils,orothersolventsontheanchoringsectionofthe
projector ceiling mount because the case could break or the projector could fall, resulting in an injury
or other accident.
■Installandroute thepower andothercablesthroughthedesignatedlocations, andbe carefulthat
they are not damaged.
■Carefully read theprojector's User's Manualprior toperformingany installationwork, and install
correctly by following all safety precautions.
■Priortoinstallation,makesuretheprojectorisOFFandunplugthepowercord.
■Donotinstallinlocations whereoil isused. Oilcanadheredueto oilsmoke orothersubstances,
resultinginabreakdown,re,orelectricalshock.Itcanalsocausedeteriorationoftheplastic,which
can result in an injury due to parts falling from the ceiling or elevated locations.
Periodic Inspection
As a general guideline, inspect the points below once per year in the same way as the set unit.
1. Check that the screws of the ceiling mount brackets and adjustment locations are not loose.
2. Inspect that the ceiling mount brackets, adjustment parts, set unit, and other parts are not broken or damaged.
01 FL-920_DD2_LensUnit_Eng_conv.indd 3 2016/01/05 21:22:33
4
Make sure the following items are packed inside the box. If something should be missing, contact the sales outlet right
away.
Accessories Packaged with FL-920 Lens Unit
Checking the Contents of Packaging
Lens mount bracket
Lens Mount bracket
User's Manual
(this manual)
Option lens FL-900
5
Code Part Name Qty. Appearance Code Part Name Qty. Appearance
(A) Mount bracket A 1
(E) Collar A 4
(B) Mount bracket B 1 (F) Hex key 1
(C)
M4×16
Hex-head screw
6 (G) Collar B 2
(D) M4×10 screws 2
Code Part Name Qty. Appearance Code Part Name Qty. Appearance
(H)
Option lens
(FL-900)
1
(
I
)
Option Lens
User's Manual
1
Names of parts are indicated with codes in the table below and on subsequent pages.
●AccessoriesPackagedwithLensMountBracket
●AccessoriesPackagedwithFL-900
01 FL-920_DD2_LensUnit_Eng_conv.indd 4 2016/01/05 21:22:33
ENGLISH
4
Make sure the following items are packed inside the box. If something should be missing, contact the sales outlet right
away.
Accessories Packaged with FL-920 Lens Unit
Checking the Contents of Packaging
Lens mount bracket
Lens Mount bracket
User's Manual
(this manual)
Option lens FL-900
5
Code Part Name Qty. Appearance Code Part Name Qty. Appearance
(A) Mount bracket A 1
(E) Collar A 4
(B) Mount bracket B 1 (F) Hex key 1
(C)
M4×16
Hex-head screw
6 (G) Collar B 2
(D) M4×10 screws 2
Code Part Name Qty. Appearance Code Part Name Qty. Appearance
(H)
Option lens
(FL-900)
1
(
I
)
Option Lens
User's Manual
1
Names of parts are indicated with codes in the table below and on subsequent pages.
●AccessoriesPackagedwithLensMountBracket
●AccessoriesPackagedwithFL-900
01 FL-920_DD2_LensUnit_Eng_conv.indd 5 2016/01/05 21:22:34
6
1. Remove the option lens FL-900 (H) from the box.
For details on operating the option lens FL-900 (H), refer to the Option Lens User's Manual (I).
2. Remove the mount brackets (A) and accessory parts from the box.
Removing the Packaged Items
Option Lens User's Manual (I)
FL-900 (H)
Mount bracket A
Accessory parts
7
1. Attach the option lens FL-900 (H) to the projector.
(For details, refer to the Option Lens User's Manual (I).
2. Provide a worktable so that no force is applied to the option lens FL-900 (H).
Put cushioning materials on top of the worktable, and place the projector upside-down on the cushioning before
starting work.
Put the option lens FL-900 (H) in a location away from the worktable.
3. Use the two M4X10 screws (D) to attach the mount bracket (B) to the option lens FL-900 (H).
Tighteningtorque:0.98N•m(10kgf•cm)
4. Remove the four adjusters from the projector. 5. Insert the four collars (E) into the removed adjusters,
and mount to the projector.
Mounting the Brackets
Option lens FL-900 (H)
Mount bracket (B)
Note the direction of
the arrow on mount
bracket (B).
M4x10 screws (D) (2 locations)
Projector
Worktable
Adjuster
Option lens FL-900 (H)
Warning
Be extremely careful when performing the mounting work. An injury or other
accident can occur if the projector falls.
Collar (E)
Adjuster Adjuster
01 FL-920_DD2_LensUnit_Eng_conv.indd 6 2016/01/05 21:22:44
ENGLISH
6
1. Remove the option lens FL-900 (H) from the box.
For details on operating the option lens FL-900 (H), refer to the Option Lens User's Manual (I).
2. Remove the mount brackets (A) and accessory parts from the box.
Removing the Packaged Items
Option Lens User's Manual (I)
FL-900 (H)
Mount bracket A
Accessory parts
7
1. Attach the option lens FL-900 (H) to the projector.
(For details, refer to the Option Lens User's Manual (I).
2. Provide a worktable so that no force is applied to the option lens FL-900 (H).
Put cushioning materials on top of the worktable, and place the projector upside-down on the cushioning before
starting work.
Put the option lens FL-900 (H) in a location away from the worktable.
3. Use the two M4X10 screws (D) to attach the mount bracket (B) to the option lens FL-900 (H).
Tighteningtorque:0.98N•m(10kgf•cm)
4. Remove the four adjusters from the projector. 5. Insert the four collars (E) into the removed adjusters,
and mount to the projector.
Mounting the Brackets
Option lens FL-900 (H)
Mount bracket (B)
Note the direction of
the arrow on mount
bracket (B).
M4x10 screws (D) (2 locations)
Projector
Worktable
Adjuster
Option lens FL-900 (H)
Warning
Be extremely careful when performing the mounting work. An injury or other
accident can occur if the projector falls.
Collar (E)
Adjuster Adjuster
01 FL-920_DD2_LensUnit_Eng_conv.indd 7 2016/01/05 21:22:52
8
6. Use the hex key (F) to loosen the screw (Q) until it stops.
7. Mount the mount bracket (A) to the mount bracket (B).
Screw (Q)
Screw (Q)
(Hole)
Mount bracket (B)
Mount bracket (A)
Insertion direction
Protrusion
9
8. Move the screw (Q) of mount bracket (A) up and down as well as left and right to insert it into the protrusion of
mount bracket (B).
It can be easier to insert when viewing from the top (hole) of mount bracket (A).
Screw (Q)
Mount Bracket (B)
Mount bracket (B)
Side view of engaged section
Screw (Q) Mount bracket (A)
(Hole)
Protrusion
Insert the protrusion of
mount bracket (B) into this
section.
01 FL-920_DD2_LensUnit_Eng_conv.indd 8 2016/01/05 21:22:54
ENGLISH
8
6. Use the hex key (F) to loosen the screw (Q) until it stops.
7. Mount the mount bracket (A) to the mount bracket (B).
Screw (Q)
Screw (Q)
(Hole)
Mount bracket (B)
Mount bracket (A)
Insertion direction
Protrusion
9
8. Move the screw (Q) of mount bracket (A) up and down as well as left and right to insert it into the protrusion of
mount bracket (B).
It can be easier to insert when viewing from the top (hole) of mount bracket (A).
Screw (Q)
Mount Bracket (B)
Mount bracket (B)
Side view of engaged section
Screw (Q) Mount bracket (A)
(Hole)
Protrusion
Insert the protrusion of
mount bracket (B) into this
section.
01 FL-920_DD2_LensUnit_Eng_conv.indd 9 2016/01/05 21:22:54
10
Use the four M4×16 hex-head screws (C) to attach the mount bracket (A) to the projector.
Tighten the M4×16 hex-head screws (C) in the order
to
.Tighteningtorque:1.47N•m(15kgf•cm)
When Using on a Tabletop
9. Return the projector to its original state.
10. Use the vertical and horizontal shift adjustment to adjust to the proper screen position.
11. Firmly tighten the screw (Q) until it is locked in place.
Warning
■ Whenever adjusting the vertical and horizontal shift, be sure to always loosen
the screw (Q). Adjusting the vertical and horizontal shift without loosening the
screw (Q) can damage the product.
■ After adjusting the vertical and horizontalshift,rmlyretightenthescrew(Q).
M4×16 hex-head screws (C)
M4×16 hex-head screws (C)
1. Peel off the the separators from the 2 collars B (G), and stick them aligned with the screw holes on the bottom case,
as shown in the diagram.
2. Use the six M4×16 hex-head screws (C) to mount the bracket (B) of the ceiling mount bracket (HAS-404U) to the
projector and mount bracket (A). Tighten the M4 × 16 hex-head screws (C) in the order
to
.
3. For the mounting work after this procedure, refer to the ceiling mount bracket (HAS-404U) user's manual.
4. Use the vertical and horizontal shift adjustment to adjust to the proper screen position.
5. Firmly tighten the screw (Q) until it is locked in place.
When Using the Ceiling Mount Bracket (HAS-404U)
M4×16
Hex-head screw (C)
HAS-404U
Bracket (B)
Mounting completed
M4×16
Hex-head screw (C)
Screw (Q)
Screw (Q)
01 FL-920_DD2_LensUnit_Eng_conv.indd 10 2016/01/05 21:23:06
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10

Hitachi FL920 User guide

Category
Projector mounts
Type
User guide

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI