Golden Lighting 9104-B14 PW-OP Installation guide

Type
Installation guide
IMPORTANT:
• ALLINSTALLATIONWORKSHOULDBEDONEBYACCREDITEDPROFESSIONAL.
• SHUTOFFPOWERSUPPLYATFUSEORCIRCUITBREAKER!
• USEONLYTHESPECIFIEDBULBS.DONOTEXCEEDTHEMAXIMUMWATTAGE!
For Customer Service, please
contact the place of purchase.
AssemblyInstructions:9104-B14, B18, B24 (Zen)
Do you have a house ground wire? If yes, proceed to step 1. If no, ip to the other side.
CLEANING TIPS
Treat the xture gently! Regular cleaning will reduce the need for deep cleaning. For regular cleaning, turn off the light and wipe down the
xture with a clean lint-free cotton or microber cloth. Never spray cleaner directly onto the xture.
1.The xture may be mounted vertically or horizontally.
Mounting bracket (I) may be positioned in various places along
cover plate (H). Please decide how you would like to mount
the xture before proceeding. (See the diagram below) Before
beginning, decide how you would like to install the xture.
PREPARING FOR INSTALLATION
Remove all of the contents from the carton. See the important notes above.
Remove the old xture from the wall, including the old mounting strap.
Please Note: The LEDs are sensitive. Try to avoid touching LED board
INSTALLING THE FIXTURE
3.Takethemountingstrapassemblyfromthepartsbag.
Nipple(F)shouldbeattachedtomountingstrap(A).You
mayneedtotightenwasher(C)andnut(D).
4.Pullthehousewires(neutralandhot)throughthe
centerofnipple(F).Pullthehouseneutralwiretothe
frontofmountingstrap(A).Loopthehouseneutralover
groundscrew(E)andtigtenwithascrewdriver.
5.Securemountingstrap(A)tothejunctionboxwith
mountingscrews(B).Tightenthescrewssecurely.
6.Bynow,youshouldknowhowyouwouldliketo
positionthexture.Slidemountingbracket(I)overthe
nipple(F)andholdituptothewall.Checkthatitislevel.
Oncelevel,takeapencilandmarkthewalltoindicate
whereanchors(J)shouldbeinserted.
2.CarefullytakeLEDmodule(O),oneofnials(N),andglassshade
(Q).Usescrews(M)toattachoneofnials(N)toLEDmodule(O).
Slideglassshade(Q)alongthetracksatthetopandbottomofLED
module(O).
Note: Theglassshouldsitinthechannel,notbehindtheentireLED
module.Usethe2remainingscrews(M)toattachtheremaining
nial(N)totheothersideofthexture.Carefullyplacethexture
onaatsurfaceforfutureuse.
CONNECTING THE WIRES
11.Haveyourassistantsupportthexture’sweightwhile
completingthewiring.Refertothewiringdiagramandattach
thexture’swirestothepowersupplywiresfromthejunction
box.ConnectHottoHotandNeutraltoNeutral.Twisttheends
ofthewirepairstogether,andthentwistonawireconnector.
Makesurealltwistsareinthesamedirection.Tuckthewires
intothecavitybetweenthebackoftheLEDpanelandthe
mountingbracket.
A
B
B
C
D
E
F
H
L
L
H
J
I
K
L
L
O
R
G
FINISHING THE INSTALLATION
12.PlaceLEDmodule(O)overmountingbracket(I).Doublecheckthatthewiresaretuckedinbeforealigningtheholesatthetopand
bottom.Usescrews(L)atthetopandbottomtosecurethexturetomountingbracket(I).
Yourinstallationisnowcomplete.Turnonthepowerandtestthexture.
H
I
Q
O
M
M
N
P
P
7.Takemountingbracket(I)awayfromthewall.
Withasmalldrillbit,makesmallholesatthe
pencilmarks.Insertanchors(J).
8.Slidecoverplate(H)andmountingbracket(I)
overthehousewiresandnipple(F).
9.Placemountingbracket(I)uptothewallso
thatyoucanseeanchors(J).Lockmounting
bracket(I)ontocoverplate(H)byslidingwasher
(G)andhexnut(R)overthewiresandthreading
ontonipple(F).
10.Anchormountingbracket(I)tothewallby
screwingmountingscrews(K)intoanchors(J)
withascrewdriverordrill.
House Wires
Fixture Wires
Hot
How to Identify the Fixture’s Wires
Hot Neutral Ground
Smooth
Ribbed
Bare Metal,
Green, or
Green Inner
Thread
Black
White
Black Inner
Thread
White Inner
Thread
IMPORTANT:
• ALLINSTALLATIONWORKSHOULDBEDONEBYACCREDITEDPROFESSIONAL.
• SHUTOFFPOWERSUPPLYATFUSEORCIRCUITBREAKER!
• USEONLYTHESPECIFIEDBULBS.DONOTEXCEEDTHEMAXIMUMWATTAGE!
For Customer Service, please
contact the place of purchase.
AssemblyInstructions:9104-B14, B18, B24 (Zen)
Do you have a house ground wire? If no, proceed to step 1. If yes, ip to the other side.
CLEANING TIPS
Treat the xture gently! Regular cleaning will reduce the need for deep cleaning. For regular cleaning, turn off the light and wipe down the
xture with a clean lint-free cotton or microber cloth. Never spray cleaner directly onto the xture.
1.The xture may be mounted vertically or horizontally.Mounting
bracket (I) may be positioned in various places along cover plate
(H). Please decide how you would like to mount the xture before
proceeding. Before beginning, decide how you would like to install
the xture.
PREPARING FOR INSTALLATION
Remove all of the contents from the carton. See the important notes above.
Remove the old xture from the wall, including the old mounting strap.
Please Note: The LEDs are sensitive. Try to avoid touching LED board (O).
6.Takemountingbracket(I)awayfromthewall.With
asmalldrillbit,makesmallholesatthepencilmarks.
Insertanchors(J).
7.Slidecoverplate(H)andmountingbracket(I)over
thehousewiresandnipple(F).Haveanassistanthold
thextureup.Slidehexnut(R)andthenwasher(G)
ontothexture’sgroundwire.
8.Passthexture’sgroundwirethroughthefrontof
nipple(F).Pullthexture’sgroundwirearoundtothe
frontofthemountingstraptolooparoundground
screw(E).Useascrewdrivertotightentheground
screw(E)ontothewiresandontothemountingstrap.
9.Placemountingbracket(I)uptothewallsothatyou
canseeanchors(J).Lockmountingbracket(I)onto
coverplate(H)byslidingwasher(G)andhexnut(R)
overthewiresandthreadingontonipple(F).
10.Anchormountingbracket(I)tothewallby
screwingmountingscrews(K)intoanchors(J)witha
screwdriverordrill.
2.CarefullytakeLEDmodule(O),oneofnials(N),andglassshade
(Q).Usescrews(M)toattachoneofnials(N)toLEDmodule(O).
Slideglassshade(Q)alongthetracksatthetopandbottomofLED
module(O).
Note: Theglassshouldsitinthechannel,notbehindtheentireLED
module.Usethe2remainingscrews(M)toattachtheremaining
nial(N)totheothersideofthexture.Carefullyplacethexture
onaatsurfaceforfutureuse.
CONNECTING THE WIRES
11.Haveyourassistantsupportthexture’sweightwhilecompletingthe
wiring.Refertothewiringdiagramandattachthexture’swirestothe
powersupplywiresfromthejunctionbox.ConnectHottoHotandNeutral
toNeutral.Twisttheendsofthewirepairstogether,andthentwistonawire
connector.Makesurealltwistsareinthesamedirection.Tuckthewiresinto
thecavitybetweenthebackoftheLEDpanelandthemountingbracket.
H
I
FINISHING THE INSTALLATION
12.PlaceLEDmodule(O)overmountingbracket(I).Doublecheckthatthewiresaretuckedinbeforealigningtheholesatthetopand
bottom.Usescrews(L)atthetopandbottomtosecurethexturetomountingbracket(I).
Yourinstallationisnowcomplete.Turnonthepowerandtestthexture.
A
B
B
C
D
E
F
H
L
L
H
J
I
K
L
L
O
R
G
INSTALLING THE FIXTURE
3.Takethemountingstrapassemblyfromthepartsbag.Nipple
(F)shouldbeattachedtomountingstrap(A).Youmayneedto
tightenwasher(C)andnut(D).Pullthehousewiresthroughthe
centerofnipple(F).
4.Securemountingstrap(A)tothejunctionboxwithmounting
screws(B).Tightenthescrewssecurely.
5.Bynow,youshouldknowhowyouwouldliketopositionthe
xture.Slidemountingbracket(I)overthenipple(F)andhold
ituptothewall.Checkthatitislevel.Oncelevel,takeapencil
andmarkthewalltoindicatewhereanchors(J)shouldbe
inserted.
Q
O
M
M
N
P
P
House Wires
Fixture Wires
Hot
How to Identify the Fixture’s Wires
Hot Neutral Ground
Smooth
Ribbed
Bare Metal,
Green, or
Green Inner
Thread
Black
White
Black Inner
Thread
White Inner
Thread
  • Page 1 1
  • Page 2 2

Golden Lighting 9104-B14 PW-OP Installation guide

Type
Installation guide

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI