Sargent P2 PASSPORT 1000 Installation Instructions Manual

Brand: Sargent

Model: P2 PASSPORT 1000

Category: Security door controllers

Type: Installation Instructions Manual

Sargent P2 PASSPORT 1000 is an ANSI/BHMA Grade 1 lock using WiFi technology that provides a cost-effective, future-proof solution for campuses and other facilities. Featuring multiCLASS SE® Technology from HID Global®, it provides simultaneous support for multiple credentials and offers an easy migration path to higher security credentials and mobile access. With no wiring required, installation is fast, easy and affordable. Some of the capabilities of the device include:

Multiple credential support: The lock supports a wide range of credentials, including mobile IDs (Bluetooth Smart), iCLASS®, iCLASS SE® (SIO-enabled), iCLASS Seos®, SIO on MIFARE® Classic, SIO on MIFARE® DESfire® EV1, MIFARE® Classic, DESfire® EV1, NFC-enabled mobile phones, and HID Prox®.

Multiple credential support: The lock supports a wide range of credentials, including mobile IDs (Bluetooth Smart), iCLASS®, iCLASS SE® (SIO-enabled), iCLASS Seos®, SIO on MIFARE® Classic, SIO on MIFARE® DESfire® EV1, MIFARE® Classic, DESfire® EV1, NFC-enabled mobile phones, and HID Prox®.

A8013H

04/16

permission of Sargent Manufacturing Company is prohibited.

PASSPORT 1000

Cylindrical Lock

Installation Instructions

1-800-810-WIRE • www.sargentlock.com • A8013H

Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.

04/30/16

Warning

Changes or modiﬁcations to this unit not expressly approved by the party respon-

sible for compliance could void the user’s authority to operate the equipment.

Table of Contents

Warning ...................................................................................3

General Description .................................................................4

Hardware Speciﬁcations .........................................................4

Electronic Speciﬁcations .........................................................4

Parts Breakdown .....................................................................5

Installation Instructions ..........................................................7

Operational Check ................................................................17

Industry Canada:

This Class B digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations. Operation is subject

to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference re-

ceived, including interference that may cause undesired operation.

Cet appareillage numérique de la classe B répond à toutes les exigences de l’interférence canadienne causant des règlements

d’équipement. L’opération est sujette aux deux conditions suivantes: (1) ce dispositif peut ne pas causer l’interférence nocive, et (2) ce

dispositif doit accepter n’importe quelle interférence reçue, y compris l’interférence qui peut causer l’opération peu désirée.

“This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be in-

stalled and operated with minimum distance 20cm between the radiator and your body. This transmitter must not be co-located or operat-

ing in conjunction with any other antenna or transmitter.”

Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain ap-

proved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should

be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.

Conformément à la réglementation d’Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d’un type et d’un

gain maximal (ou inférieur) approuvé pour l’émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique

à l’intention des autres utilisateurs, il faut choisir le type d’antenne et son gain de sorte que la puissance isotrope rayonnée équivalente

(p.i.r.e.) ne dépasse pas l’intensité nécessaire à l’établissement d’une communication satisfaisante.

Any retroﬁt or other ﬁeld modiﬁcation to a ﬁre rated opening can potentially impact the ﬁre rating of the opening, and SARGENT Manufac-

turing makes no representations or warranties concerning what such impact may be in any speciﬁc situation. When retroﬁtting any portion

of an existing ﬁre rated opening, or specifying and installing a new ﬁre-rated opening, please consult with a code specialist or local code

ofﬁcial (Authority Having Jurisdiction) to ensure compliance with all applicable codes and ratings.

FCC

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the

FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential instal-

lation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accor-

dance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or televi-

sion reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

To avoid possible damage from electrostatic discharge (ESD), some basic precautions should be used when handling

electronic components:

• Minimize build-up of static by touching and/or maintaining contact with unpainted metal surfaces such as

door hinges, latches, and mounting plates especially when mounting electronic components such as readers

and controllers onto the door.

• Leave components (reader and controller) protected in their respective anti-static bags until ready

for installation

• Do not touch pins, leads or solder connections on the circuit boards

4 1-800-810-WIRE • www.sargentlock.com • A8013H

Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.

04/30/16

Passport 1000 P2 WiFi Cylindrical Lock

General Description

Hardware Specifications

Electronic Specifications

• Inside lever retracts latch

• Outside lever controlled by any combination of

keypad, magnetic swipe, contactless reader or

mechanical cylinder

• ANSI/BHMA A156.25 Listed Grade 1 Compliant

• May be used for indoor and outdoor applications

• Complete locksets with controller

• Easily retroﬁts existing Passport 1000

(cylindrical lock) door preps

• ADA Compliant

• Latch 1/2” standard 3/4” throw ﬁre-rated

double doors (optional) (41- preﬁx)

• Deadlocking latch

• WiFi (IEEE 802.11 b/g/n)

• Multiple time zone and holiday access scheduling

• First-in unlock or automatic unlock conﬁguration,

based on speciﬁed time schedule

• Support for most advanced wireless encryption

and authentication standards such as WEP, WPA,

WPA2 and 802.1x*

• 2,400 users per lock; 10,000 event audit trail

• Privacy button

*For speciﬁc security information, please contact your local

ASSA ABLOY Door Security Solutions sales consultant or

call 800-810-WIRE.

• HID

multiCLASS SE

technology offers

support for the following credentials:

• 2.4 GHz credential compatibility:

• 125 kHz credential compatibilty:

• HID Prox

• Secure Identity Object™ (SIO) on

Mobile IDs (Bluetooth Smart)

• 13.56 MHz credential compatibility:

• iCLASS

• iCLASS SE

(SIO-enabled)

• iCLASS Seos

• SIO on MIFARE

Classic

• SIO on MIFARE

DESﬁre

EV1

• MIFARE

Classic

• DESﬁre

EV1

• NFC-enabled mobile phones

Destructive Attack Level 1

Line Security Level 1

Endurance Level 4

Standby Power Level 1

Power Requirements:

• Alkaline AA Batteries: 9V, 300mA

• Optional Hard Power (UL294 Listed Power

Supply Required): 9-24VDC, 300mA

• UL Listed - UL 294 Indoor Use

• CUL Listed - S319: Class 1

• UL 294 Access Control Ratings:

An ANSI/BHMA Grade 1 lock using WiFi technology, the Passport 1000 P2 cylindrical lock provides a

cost-effective, future-proof solution for campuses.

Featuring multiCLASS SE

Technology from HID Global

, it provides simultaneous support for multiple

credentials and offers an easy migration path to higher security credentials and mobile access.

With no wiring required, installation is fast, easy and affordable.

Note: A weather-protective gasket is required

for outdoor applications.

04/30/16

1-800-810-WIRE • www.sargentlock.com • A8013H 5

Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.

Passport 1000 P2 WiFi Cylindrical Lock

Parts Breakdown

P2 WiFi Lock with Magnetic Card Swipe With or Without Keypad

ITEM No. PART No. DESCRIPTION

1 52-3583-[ﬁnish] Outside Escutcheon Assemby, mag stripe

52-3582-[ﬁnish] Outside Escutcheon Assemby, mag stripe and Keypad (shown)

52-4244-[ﬁnish] Outside Escutcheon Assemby, Mag Swipe, Keypad, and HID 125 kHz Prox

52-4759-[ﬁnish] Outside Escutcheon Assemby, iCLASS, keypad, mag stripe, Prox, smart card (MIFARE, DESFIRE - shown)

52-4777-[ﬁnish] Outside Escutcheon Assemby, iCLASS, mag stripe, Prox, smart card (MIFARE, DESFIRE)

52-4787-[ﬁnish] Outside Escutcheon Assemby, FeliCa, keypad, mag stripe, Prox

52-4788-[ﬁnish] Outside Escutcheon Assemby, FeliCa, mag stripe, Prox

52-4894-[ﬁnish]* Outside Escutcheon Assemby, Standard Reader and Keypad

52-4895-[ﬁnish]* Outside Escutcheon Assemby, Standard Reader

52-4896-[ﬁnish]* Outside Escutcheon Assemby, Felica Reader and Keypad

52-4897-[ﬁnish]* Outside Escutcheon Assemby, Felica Reader

52-4779 Mounting Plate Assembly

3 52-5409 WiFi Controller Assembly

4 52-4776-[ﬁnish] Inside Escutcheon Assembly with Privacy Button

5 52-5373 Door Position Switch Kit

*Bluetooth

Smart option

6 1-800-810-WIRE • www.sargentlock.com • A8013H

Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.

04/30/16

Passport 1000 P2 WiFi Cylindrical Lock

10 Line Series Cylindrical Lock

Parts Breakdown (Continued)

*Adapter Plate/Spacer (10-0847)

only shipped with orders that

specify 1-3/8” doors.

Tools Required:

• #2 Phillips screwdriver

• Flat head

• T20 Torx

driver

ITEM PART No. DESCRIPTION REQ’D

1 --- Outside Lever (Reference Catalog for Available Styles) 1

2 10-0043 Lever Retainer Key (In Screw Pack 10-2052) 1

3 --- Cylinder Assembly (Reference Catalog for Available Cylinders) 1

4 --- Rose (Reference Catalog for Avalable Styles) 2

5 10-0792 Spacer Bushing 2

6 10-3049 Outside Rose Spring Assembly 1

7 10-3449 Lockbody Assembly 10G77 - Standard Cylinder 1

10-3450 Lockbody - LFIC 1

10-3451 Lockbody - SFIC 1

7a 52-4844 Lockbody Harness 1

8 10-0847 Adapter Plate/Spacer (*Only Included With 1-3/8” Thick Doors) 2

9 10-3192 Latch Assembly 1

10 10-2052 Screw Pack 2

11 10-3048 Inside Rose Spring Assembly 1

12 --- Inside Lever (Reference Catalog for Available Styles) 1

04/30/16

1-800-810-WIRE • www.sargentlock.com • A8013H 7

Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.

Passport 1000 P2 WiFi Cylindrical Lock

1 Door Preparation

Installation Instructions

A. Verify Hand and Bevel of Door

Stand on outside of locked door when determining door hand.

• Prior to installation, all holes must be free of burrs, debris and sharp edges.

• If doors are not properly reinforced per ANSI 115.2, commercially available

reinforcements should be installed.

• Prepare door according to appropriate template:

• Field template A8068 (for wood doors) with DPS

• Field template A8069 (for wood doors) without DPS

• Manufacturer’s template 4655 with DPS.

• Manufacturer’s template 4691 without DPS.

Fig. 1

Door

Position

Switch

Latch

Front

and Hole

Escutcheon Through Bolt Holes

Inside Mouthing Plate Holes

Controller Wire Hole

Wire Run Channel

Lock Body Through Bolt Hoes

Alignment Notches

Lock Body Prep

Escutcheon Through Bolt Holes

Controller Wire Hole

Lockbody Through Bolt Holes

Alignment Notches

Lock Body Prep

B. Door Preparation

Outside of Door

Inside of Door

Left Hand (LH)

Hinges Left.

Open Inward.

Left Hand

Reverse Bevel

(LHRB)

Hinges Left.

Open Outward.

Right Hand (RH)

Hinges Right.

Open Inward.

Right Hand

Reverse Bevel

(RHRB)

Hinges Right.

Open Outward.

Raceway for Power (Optional)

8 1-800-810-WIRE • www.sargentlock.com • A8013H

Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.

04/30/16

Passport 1000 P2 WiFi Cylindrical Lock

2 Install Strike

Install strike in the door frame (Fig.2).

(2) #8-32 x 3/4” Screws

Fig. 2

Centerline of Latch

Front and Strike

Outside of Door

Fig. 3A

Latch Assembly

(2) #8-32 x 3/4”

Combination

Screws

IMPORTANT: Latch bevel must match door bevel and

deadlocking latch must stop on strike when door is closed.

Strike

Deadlocking Latch

Fig. 3B Detail

Install Latchbolt

1. Install latch with beveled bolt facing strike.

2. Attach with two screws.

DO NOT tighten completely at this time.

IMPORTANT:

• Door must remain open during installation

• Use door stop

04/30/16

1-800-810-WIRE • www.sargentlock.com • A8013H 9

Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.

Passport 1000 P2 WiFi Cylindrical Lock

Install Door Position Switch (DPS)

Horizontal

of Strike

Door Position

Switch Hole

Dim 2

(See template)

Dim 1

Fig. 4A

Vertical

of Strike

Fig. 4B

Wood Frame Metal Frame

Dim 1

3/8” 3/4”

Strike for Cylindrical Lock

Collar is used only

with metal doors.

Door Position

Switch (DPS)

Inside of Door

1. Insert connector end of DPS harness through raceway on latch

edge of door.

Note: Use collar in METAL door only.

2. Push DPS ﬁrmly into place by hand.

Important: DO NOT TAP SWITCH WITH ANY TOOL.

10 1-800-810-WIRE • www.sargentlock.com • A8013H

Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.

04/30/16

Passport 1000 P2 WiFi Cylindrical Lock

Lock Presets and Adjustments (If Required)

A. Lock Preset

▪ Lock body holes – 12 and 6 o’clock

(Fig. 5A).

▪ Door thickness – 1-3/4” thick. Refer to

adjustments below for other door

conditions (Fig. 5B).

B. Through-Bolt and Door Thickness Adjustment

(If Required)

▪ Remove outside lever (Fig. 5A), scalp and

spacer bushing.

▪ Rotate mounting plate to either align with

through-bolt holes in door or adjust for

proper door thicknesses (Fig. 5A and 5B).

See markings on through-bolt post.

▪ Re-install spacer bushing (to align

with back of lever), scalp and lever.

Fig. 5A

Lock Body Holes

Spacer Bushing

Rotate to match

lock body holes in door.

Fig. 5B Detail

1-3/4” Thick Doors

2” Thick Doors

C. How To Remove Outside Lever (If Necessary)

1. Insert key, rotate 45° clockwise and hold (Fig. 5C).

2. Depress lever retainer with push pin tool (provided).

1. With outside lever in hand, use standard

pliers to pull out cylinder retainer.

2. Remove key and cylinder from lever.

3. Insert new cylinder.

4. Secure by pressing cylinder retainer ﬂush.

D. How To Change Cylinder (If Necessary)

Fig. 5C

Outside Lever

Key

Cylinder Retainer

Fig. 5D

Cylinder

Washers (Only 30- Preﬁx)

04/30/16

1-800-810-WIRE • www.sargentlock.com • A8013H 11

Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.

Passport 1000 P2 WiFi Cylindrical Lock

Install Lock

1. Feed wires followed by the lockbody from

outside of door through the lockbody hole (Fig. 6A).

2. Lockbody must engage both the latchbolt unit prongs

and tail piece (Fig. 6B).

Secure Lock To Door

Fig. 6B Detail

Wire Harness

(From Lock Body)

Cylindrical Lock Body

and Outside Trim

Wire Harness

(From Lockbody)

Grounding Harness

(Wood Doors Only)

Put ground ring terminal

through top ﬂat head

screw and tighten down.

(2) #10-32 x 1-1/4”

Flat Head Machine

Screws (Secures

outer spring housing)

Spring housing

assembly

Fig. 7A

Fig. 7B Detail

IMPORTANT: If lock is being installed as a retroﬁt;

(replacing an existing P2 product), remove the

DPS wires and connector (Fig. 6A) by simply

severing the wires as indicated (see arrow).

If this is a new lock being installed for the ﬁrst

time, DO NOT REMOVE wires and connector.

Fig. 6A

Grounding Harness

from Lock Body

(Wood Doors Only)

Cut wires here

(if required)

Ground

Wire

1. Feed wire and connector:

• For wood door, feed connectors and wires through the door and up

the wire run channel (Fig. 7A).

• For metal door (not shown), feed connectors and wires into the lock-

body hole and out the controller hole.

2. Position ground lug between (top) #10-32x1-1/4”

through-bolt and rose assembly (Fig. 7A).

NOTE: Proper placement of

ground wire (Fig. 7A, B)

will prevent pinching or

damage to the ground wire.

3. Secure rose assembly with (2)

#10-32x1-1/4” through-bolts.

4. Secure latch by fully tighten-

ing (2) #6 x 3/4” self-tapping

screws (refer to previous sec-

tion 3 - Install Latchbolt).

12 1-800-810-WIRE • www.sargentlock.com • A8013H

Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.

04/30/16

Passport 1000 P2 WiFi Cylindrical Lock

Assemble Inside Trim

1. Verify spacer bushing is inserted horizontally and aligned

with lever (Fig. 8).

2. Place rose (scalp) over shaft of lock body against

surface of door; hand-tighten, turning clockwise.

3. Attach lever. Push until engaged.

Fig. 8

Inside of door

Spacer Bushing

Rose (Scalp)

DPS (Door Position Switch)

Inside Lever

Install Wire Cover Plate (Wood Door Only)

1. Position the wire cover plate above the rose and covering

the wire channel. Mark the hole positions.

2. Ensure stamped side of plate is against the door.

3. Drill (2) 3/32” diameter by 1/2” deep holes (Fig. 9A).

4. Cover wires with cover plate by securing plate to door

directly above rose using two (2) #6 x 1/2” ﬂat head security

torx wood screws (Fig. 9A).

Note: Tuck wires and ferrite in hole at top of wire channel

(Fig. 9A). Position lower edge of cover plate against the rose

to ensure no wires are visible and make sure the plate is

oriented correctly (Fig. 9B).

Inside of door

Wire Cover

Fig. 9B Detail

This Side Down

Fig. 9A

Back Side of

Wire Cover Plate

(2) #6 x 1/2”

Flat Head Security

Torx Wood Screws

04/30/16

1-800-810-WIRE • www.sargentlock.com • A8013H 13

Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.

Passport 1000 P2 WiFi Cylindrical Lock

Note: Gasket optional, for non-ﬁre rated doors only.

For non-ﬁre rated door applications, an optional gasket

(Part number 52-0782) may be used as a weather seal

between the escutcheon and the outside door surface.

Install Outside Escutcheon with (Optional) Gasket

Outside

Escutcheon

Outside of Door

Fig. 10

Gasket

Reader

Cable

1. On the inside of the door, position the mounting plate

over the indicated holes.

2. Feed lockbody, reader and DPS cables through central

opening (Fig. 11).

3. Route ground ring terminal from lock body under bot-

tom of mounting plate and attach to bottom left corner

using one #8-32 x 1-7/8” ﬂat head machine screw.

4. Insert other three #8-32 x 1-7/8” ﬂat head machine

screws and tighten, fastening the outside escutcheon

to the door (Fig. 11).

Mounting Plate Assembly

Fig. 11

Peel off adhesive backing and attach to (outside) escutcheon.

1. Position the outside escutcheon, aligning the posts with

the door prep (Fig. 10).

2. Feed reader cable through opening.

IMPORTANT: If the following step is skipped, the product

will not be UL-compliant:

3. Attach two (2) #8 x 3/8” ﬂat head wood screws for

wood doors or (2) #8-32 x 3/8” ﬂat head machine

screws for metal doors (Fig. 11).

(4) #8 - 32 x 1-7/8” Flat

Head Machine Screws

Mounting Plate

(2) #8 - 3/8” ﬂat head

Wood Screws

Ground Lug

14 1-800-810-WIRE • www.sargentlock.com • A8013H

Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.

04/30/16

Passport 1000 P2 WiFi Cylindrical Lock

Fig. 12

Ground

Lugs

Lock

Body

(10-pin)

Reader

(24-pin)

Board-to-Board

Connector

DPS (4-pin)

12 Installation of Connectors

1. Tuck excess cable into wire hole on inside of door.

2. Secure the mounting assembly while ensuring proper alignment of outside reader and fully tighten

the (2) through-bolts on the inside of the door to secure the reader and plate to the door.

Secure the following connectors to their respective terminals (Fig. 12):

A. Secure the 4-pin DPS connector.

B. Secure the 10-pin lock body assembly connector.

CAUTION - Do not touch or allow debris to enter connector contacts.

Secure Mounting Plate

IMPORTANT: Do not run wires through bottom hole in plate (Fig. 12) - it will damage wires and the controller connector. Route

wires around ﬂange, do not route wires through the ﬂange hole (Fig. 12).

C. Secure the 24-pin card reader connector (Fig. 12).

04/30/16

1-800-810-WIRE • www.sargentlock.com • A8013H 15

Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.

Passport 1000 P2 WiFi Cylindrical Lock

Install Inside Module Component Assembly

Fig. 13

1. Insert top tabs of controller into slots on mounting plate (Fig. 13).

2. Ensure proper alignment of board-to-board connectors while pivoting

bottom of controller toward door until tab on bottom snaps securely

into place on mounting plate.

CAUTION: To avoid possible damage to board-to-board connectors, care should be

taken when securing controller to mounting plate. If there is resistance when

securing, detach controller to determine cause before re-attaching controller.

16 1-800-810-WIRE • www.sargentlock.com • A8013H

Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.

04/30/16

Passport 1000 P2 WiFi Cylindrical Lock

Battery Installation

Fig. 14

(2) #8-32 x 1/2”

Secure Torx

Machine Screws

Fig. 15

Installation of Inside Escutcheon

1. Place (6) “AA” batteries into the compartment being

careful to align polarity (- & +) properly.

2. After batteries are properly installed, there is a slight

delay followed by a amber LED ﬂash; the lock motor

will cycle.

Inside of Door

1. Position inside escutcheon as shown (Fig. 13).

Verify that all wires are positioned within the escutcheon

to avoid pinching.

2. Attach escutcheon with (2) #8-32 x 1/2” T-20 Torx pan

head screws.

3. Straighten escutcheon and tighten securely.

DO NOT OVERTIGHTEN.

04/30/16

1-800-810-WIRE • www.sargentlock.com • A8013H 17

Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.

Passport 1000 P2 WiFi Cylindrical Lock

Operational Check

IMPORTANT: Be sure to test functions prior to closing door.

In all cases, perform the following checks:

1. Ensure that inside lever retracts latch.

• For units with cylinders, the following checks apply:

Insert key into cylinder and rotate:

a. There should be no friction against lock case or any other

obstructions. If friction or binding occurs, readjust cylinder to

eliminate issues.

b. The key should retract the latch and the key should rotate freely.

• For units without a keypad, add card using LCT software* and test.

• For units with a keypad, add pin and card using LCT software*

and test.

2. LED signaling:

• After using a valid credential, a green ﬂash followed by three fast

amber ﬂashes indicates a low power condition.

Check the battery voltage.

If the voltage is low, replace the batteries.

• If the lock loses power, it will ﬂash rapid blue for approximately one

minute. Lock will default to programmed fail safe or fail secure.

3. When you have completed the tests, close the door, ensuring latchbolt fully

extends into strike plate without binding.

*Refer to Network and Lock Conﬁguration Tool user manual (WFMN1) for

information on how to conﬁgure and program locks.

NOTES

SARGENT Manufacturing

100 Sargent Drive

New Haven, CT 06511 USA

800-810-WIRE (9473) • www.sargentlock.com

Founded in the early 1800s, SARGENT® is a market leader in locksets, cylinders, door closers, exit devices,

electro-mechanical products and access control systems for new construction, renovation, and replacement applications.

The company’s customer base includes commercial construction, institutional, and industrial markets.

Reproduction in whole or in part without the express written permission of Sargent Manufacturing Company is prohibited.

ASSA ABLOY is the global leader in door opening solutions, dedicated to

satisfying end-user needs for security, safety and convenience.

A8013H -04/16

Sargent P2 PASSPORT 1000 Installation Instructions Manual

Brand: Sargent

Model: P2 PASSPORT 1000

Category: Security door controllers

Type: Installation Instructions Manual

Multiple credential support: The lock supports a wide range of credentials, including mobile IDs (Bluetooth Smart), iCLASS®, iCLASS SE® (SIO-enabled), iCLASS Seos®, SIO on MIFARE® Classic, SIO on MIFARE® DESfire® EV1, MIFARE® Classic, DESfire® EV1, NFC-enabled mobile phones, and HID Prox®.

Download PDF

report

Sargent P2 PASSPORT 1000 Installation Instructions Manual

Sargent P2 PASSPORT 1000 Installation Instructions Manual

Related papers

Other documents