Samsung SOC-222 User manual

Page is loading ...

2

3

Important Safety Instructions

E E

6. If this product fails to operate normally, contact the store of purchase or

your nearest service center. Never disassemble or modify this product in any

way. (The manufacturer is not liable for any damage resulting from

unauthorized disassembly or repairs.)

7. When cleaning, do not spray water directly onto parts of the product. (Doing

so may cause fire or electric shock.) Wipe the surface with a dry cloth.

Never use detergents or chemical cleaners on the product, as this may result

in discoloration of surface or cause damage to the finish.

1. Do not drop objects on the product or apply strong shock to it. Keep away

from a location subject to excessive vibration or magnetic interference.

2. Do not install in a location subject to high temperature (over 50

°

C

/

122

°

F),

low temperature (below -10

°

C

/

14

°

F), or high humidity. (Doing so may cause

fire or electric shock).

3. Avoid a location which is exposed to direct sunlight, or near heat sources

such as heaters or radiators. (Neglecting to do so may result in a risk of fire).

4. If you want to relocate the already installed product, be sure to turn off the

power and then move or reinstall it.

5. Install in a well - ventilated location.

6. Remove the power plug from the outlet when there is a lightning storm.

(Neglecting to do so may cause fire or damage to the product.)

CAUTION: TO REDUCE THE RISK OF

ELECTRIC SHOCK, DO NOT

REMOVE REAR COVER. NO

USER SERVICEABLE PARTS

INSIDE. REFER TO QUALIFIED

SERVICE PERSONNEL.

1. Make sure that the cable is plugged in securely before using.

(A loose connection may result in fire.)

2. When installing the camera on a wall or ceiling, mount it safely and

securely. (A falling camera may cause personal injury.)

3. Do not place conductive objects (e.g., screwdrivers, coins, and

metal things) or containers filled with water on top of the camera.

(Serious injury may result from fire, electric shock, or falling objects.)

4. Do not install in a sooty, dusty, or humid location.

(Doing so may cause fire or electric shock.)

5. If any unusual smells or smoke come from the unit, stop using the

product. In such case, immediately disconnect the power source and

contact the service center. (Continued use in such a condition may

cause fire or electric shock.)

This symbol indicates high voltage

is present inside. It is dangerous

to make any kind of contact with

any inside part of this product.

This symbol alerts you that

important literature concerning

operation and maintenance has

been included with this product.

CAUTION

RISK OF ELECTRIC

SHOCK DO NOT OPEN

AB68-00431A SOC-222(P)-GB 2003.11.26 9:47 AM Page 2

4

5

Table of Contents

E E

Chapter 1 About SOC-222(P) 5

Chapter 2 Before Installation 6

Installing SOC-222(P) 8

Appendix SOC-222(P) Pin Configuration 13

SOC-222(P) Specification 14

About SOC-222(P)

The SOC-222(P) is a camera for SMO-210T(P) only. It contains a mike

inside and will be installed easily by a general user.

Meanwhile, the SOC-222(P) is shaped like a infrared ray sensor to reduce

the hatred for the conventional camera and it is featured to have the AUTO

WHITE BALANCE function and a mike.

AB68-00431A SOC-222(P)-GB 2003.11.26 9:47 AM Page 4

E

7

E

Checking Contents

Be sure to check the package contains all the items in it, camera, bracket,

accessory box, and cable when unpacked.

6

Before Installation

✔ Check if the place is hard enough to endure 5 times the total weight (1kg or

so) of Camera before installation.

✔ Don’t let the cable get stuck in a wrong place nor let the insulating cover peeled

(to avoid breakdown or fire).

✔ Don’t let people or valuables under the installation place so that they don’t get

hurt from a falling material.

✔ Put the SOC-222(P) in a cool place free from a direct ray regardless of that you

use or just keep it.

✔ The SOC-222(P) shall be used in the place where the following conditions are

maintained all the time.

- Temperature : -10°C ~ +50°C (14°F~122°F)

- Humidity : Below 90%

Precautions

AB68-00431A SOC-222(P)-GB 2003.11.26 9:47 AM Page 6

9

E

1. Choose a place hard enough to endure 5 times the total product weight(5Kg or so).

2. Example of Camera Installation

! On the wall @ On the ceiling

3. Contact the base camera with the installation point(wall or

ceiling), mark the hole position with a pencil, drill a hole

(5mm ID and 35mm deep) for fixing the base camera, and

insert the supplied plastic anchor(HUD 5) into the hole to

the end.

WALL

CEILING

8

E

Installing SOC-222(P)

✔ In case electromagnetic waves affect SOC-222(P), please wind the core ferrite

at a proper point. (The core ferrite is contained in SOC-222P only.)

CORE - FERRITE

CABLE

Precautions

AB68-00431A SOC-222(P)-GB 2003.11.26 9:47 AM Page 8

11

E

10

E

8. Move the holder rear to control the direction.

9. Turn the screw inside the assembly bracket

camera with a cross-headed driver to tighten.

10.Turn the side screw machine (BH M2.6) in

the camera main body counterclockwise to loosen. Then, lift it a little and push it

in the arrow direction to separate the assembly case front and case rear.

11. Assemble the camera to the RJ-45 jack in the rear part of the camera main

body.

12.Put the bottom hole of the assembly

bracket camera and case rear in the

square groove as shown in the figure so

that the case rear can be hooked by the

assembly bracket camera hook.

(Be sure to lift the case rear a little bit

before inserting.)

CASE-FRONT

BH M2.6

CASE-REAR

4. Make a groove at the bottom of the base camera

with a knife so that the RJ-45 connector cable

goes out of the camera along the wall. (Choose

one out of 6 points at least 0.5mm thick.)

5. Put the RJ-45 connector cable to be connected

to the camera through the center hole of the

base camera. Insert the RJ-45 connector cable

into the groove to enable the camera to go out

along the wall.

6. Fix the assembly bracket camera in a hole on the wall or ceiling for installation.

Align the camera installation hole with the hole with a plastic anchor inserted into and

tap an assembly screw(TH M4 x 30) at 2 points.

7. Turn the screw inside the assembly bracket

assembly bracket camera counterclockwise with

a cross-headed driver to loosen a little.

CAMERA- BRACKET

HOLE

RJ - 45 CONNECTOR CABLE

HOLDER-REAR

AB68-00431A SOC-222(P)-GB 2003.11.26 9:47 AM Page 10

13

E

12

E

14. Assemble the case front detached from

the camera main body downward as

shown in the figure.

Turn the side screw machine(BH M2.6)

clockwise for tightening.

CASE-FRONT

BH M2.6

CASE-REAR

12-1. Turn the case rear clockwise by 90˚

and put the camera as shown in No. 12

to install the camera vertically.

13. Tighten it by tapping screws (BH M3).

(No. 12 : Tighten b . No. 12 1 : Tighten a .)

a

b

AB68-00431A SOC-222(P)-GB 2003.11.26 9:47 AM Page 12

15

E

14

E

PARAMETER

DESCRIPTION

SOC-222 SOC-222P

Product Type PIR Type Normal camera PIR Type Normal camera

Power Source Voltage DC 12 ~ 18V From Monitor DC 12 ~ 18V From Monitor

Power Consumption Approx. 2W Approx. 2W

Broadcast System NTSC Standard Color Camera PAL Standard Color Camera

Image Device 1/4 inch IT Super HAD CCD 1/4 inch IT Super HAD CCD

Effective Pixel 510(H) X 492(V) 500(H) X 582(V)

Scanning Method 525 Line, 2:1 Interlace 625 Line, 2:1 Interlace

Line frequency Horizontal : 15,734Hz Horizontal : 15,625Hz

Vertical : 60Hz Vertical : 50Hz

Synchronization Method INT INT

Resolution 330 TV Lines 330 TV Lines

S/N Ratio Over 48dB Over 48dB

Minimun Sence Illumination 2 Lux(F2.0 50IRE) 2 Lux(F2.0 50IRE)

Color Temperature ATW ATW

Electronic Shutter ELC ELC

Signal OutPut Composite Video Out : 1.0Vp-p Composite Video Out : 1.0Vp-p

75 Ohms/RJ45 Jack 75 Ohms/RJ45 Jack

Lens Focal Length : 3.8mm Focal Length : 3.8mm

Aperture(F) : F2.0 Aperture(F) : F2.0

Operating Temperature -10°C +50°C -10°C ~ +50°C

Operating Humidity ~90% ~90%

Physical Size 69.1(W) X 114.15(H) X 47.5(L) 69.1(W) X 114.15(H) X 47.5(L)

Weight Approx. 150g Approx. 150g

SOC-222(P) Specification

SOC-222(P) Pin Configuration

Pin Number Specification

1 DATA+

2 VIDEO_OUT

3 GND

4 DATA-

5 AUDIO_OUT

6 VDD

7 GND_V

8 CH_SEL

8 ... 1

AB68-00431A SOC-222(P)-GB 2003.11.26 9:47 AM Page 14

Page is loading ...

SOC-222(P)

Manual de instalación

Es

AB68-00431A SOC-222(P)-spa 2003.11.26 9:51 AM Page 1

Page is loading ...

15

NL

14

NL

PARAMETER

BESCHRIJVING

SOC-222 SOC-222P

Type product PIR-type Normale camera PIR-type Normale camera

Stroomvoorziening 12 tot 18V gelijkstroom van monitor 12 tot 18V gelijkstroom van monitor

Stroomverbruik Ongeveer 2W Ongeveer 2W

TV-uitzendsysteem NTSC-standaardkleurencamera PAL-standaardkleurencamera

Beeldverwerkingsapparaat 1/4-inch IT Super HAD CCD 1/4-inch IT Super HAD CCD

Effectieve aantal pixels 510 (H) X 492 (V) 500 (H) X 582 (V)

Scanmethode 525 lijnen, 2:1 Interlace 625 lijnen, 2:1 Interlace

Lijnfrequentie Horizontaal : 15.734 Horizontaal : 15.625

Verticaal : 60 Hz Verticaal : 50 Hz

Synchronisatiemethode INT INT

Resolutie 330 TV-lijnen 480 TV-lijnen

Signaal-ruisverhouding Meer dan 48dB Meer dan 48dB

Minimale verlichtingsvereiste

2 lux (F2.0 50IRE) 2 lux (F2.0 50IRE)

Kleurtemperatuur ATW ATW

Elektronische sluiter ELC ELC

Signaaluitvoer Composite Video-uitgang : 1.0 Vp-p Composite Video-uitgang : 1.0 Vp-p

75 ohm/RJ45 75 ohm/RJ45

Lens Brandpuntsafstand : 3,8 mm Brandpuntsafstand : 3,8 mm

Diafragma (F) : F2.0 Diafragma (F) : F2.0

Gebruikstemperatuur -10°C tot +50°C -10°C tot +50°C

Luchtvochtigheid bij gebruik

Tot 90% Tot 90%

Afmetingen

69,1mm (B) x 114,15 mm (H) x 47,5 mm (L) 69,1mm (B) x 114,15 mm (H) x 47,5 mm (L)

Gewicht Ongeveer 150g Ongeveer 150g

Productspecificaties van de SOC-222P

Pinconfiguratie van de SOC-222P

Pinnummer Specificaties

1 DATA+

2 VIDEO_OUT

3 GND (AARDE)

4 DATA-

5 AUDIO_OUT

6 VDD

7 GND_V

8 CH_SEL

8 ... 1

AB68-00431A SOC-222(P)-NL 2003.11.26 9:55 AM Page 14

Page is loading ...

15

DK

14

DK

PARAMETER

BESKRIVELSE

SOC-222 SOC-222P

Produkttype PIR-type normalt kamera PIR-type normalt kamera

Spænding for strømkilde DC 12~18V fra monitor DC 12~18V fra monitor

Strømforbrug Ca. 2W Ca. 2W

Udsendelsessystem NTSC Standard farvekamera PAL Standard farvekamera

Billedudstyr 1/4 tomme IT Super HAD CCD 1/4 tomme IT Super HAD CCD

Effektiv pixel 510(H) X 492(V) 500(H) X 582(V)

Scanningsmetode 525 linje, 2:1 skærmskandering 625 linje, 2:1 skærmskandering

Linjefrekvens Vandret : 15.734 Vandret : 15.625

Lodret : 60 Hz Lodret : 50 Hz

Synkroniseringsmetode INT INT

Opløsning 330 TV-linjer 330 TV-linjer

Støj-forhold Over 48dB Over 48dB

Minimum scenebelysning 2 Lux (F2.0 50IRE) 2 Lux (F2.0 50IRE)

Farvetemperatur ATW ATW

Elektronisk lukker ELC ELC

Signaludgang Composite videoudgang : 1.0 Vp-p Composite videoudgang : 1.0 Vp-p

75 ohms/RJ45 75 ohms/RJ45

Linse Focal-længde : 3,8 mm Focal-længde : 3,8 mm

Åbning(F) : F2,0 Åbning(F) : F2,0

Driftstemperatur -10°C +50°C -10°C ~ +50°C

Driftsfugtighed ~90% ~90%

Størrelse 69,1mm(B) x 114,15mm(H) x 47,5mm(L) 69,1mm(B) x 114,15mm(H) x 47,5mm(L)

Vægt Ca. 150g Ca. 150g

SOC-222(P)- Specifikationer

SOC-222(P)-Pin-konfiguration

Pin-nummer Specifikation

1 DATA+

2

3 GND

4 DATA-

5

6 VDD

7 GND_V

8

8 ... 1

VIDEO_OUT (videoudgang)

CH_SEL (kanalvælger)

AUDIO_OUT (audioudgang)

AB68-00431A SOC-222(P)-dan 2003.11.26 10:6 AM Page 14

Page is loading ...

SOC-222(P)

àÌÒÚÛÍˆËﬂ ÔÓ ÛÒÚ‡ÌÓ‚ÍÂ

R

AB68-00431A SOC-222(P)-rus 2003.11.26 10:11 AM Page 1

Page is loading ...

ELECTRONICS

Part No. AB68-000431A

Printed in Korea

AB68-00431A SOC-222(P)-ITA 2003.11.27 11:17 AM Page 16

Samsung SOC-222 User manual

Samsung SOC-222 User manual

in other languages

Related papers

Other documents