Accutone T1 User Manual & Installation Manual

Brand
Accutone
Model
T1
Type
User Manual & Installation Manual
Printed in Hong Kong
ATL-T117042009V1
Accutone and the logo device are registered trademarks of Accutone Technologies Limited.
© Copyright 2009 Accutone Technologies Limited, All rights reserved, Do not copy or re-distribute any contents.
T1 Professional Headset Telephone
User Manual & Installation Guide
Telephone
www.accutone.com
1
Introduction.
®
Thank you for purchasing the Accutone T1 Headset Telephone. T1 is
specifically designed to be used with any standard PSTN telephone
network, replacing your traditional telephone. Allowing direct connection
to any Accutone telephone headset, the T1 provides true handsfree
communication for use in homes, small offices and call centers.
Designed from the same award-winning design-team of Accutone, the T1
combines both functionality and aesthetics. It is perhaps the best looking
headset telephone you can find in any markets. The T1, aside from basic
calling features like flash, redial, pause and microphone mute, it also offers
many added features like multi-status online-indicator, connection to
recording devices as well as a headset hanger.
The T1 Telephone is the best companion to the Accutone telephone
headset series, providing top-end voice communication that is above
industry standards. Please spend some time to study this user manual
before you proceed to the installation, and we are confident that you will
enjoy the many benefits this product has to offer.
table of content.
®
any Accutone
telephone headset
ONE
T1 headset telephone
This installation guide and user manual contains the following contents:
professional headset telephone
T1
direct connection
P.3
P.4
P.4
P.5
P.5
P.6
P.6
P.7
P.7
P.8
P.8
P.8
P.9
P.9
P.9
PART A Connections & Preparations.
A.1 Main Switches & Interface
A.2 Connect to Wall Jack
A.3 Connect to an Additional Terminal Extension
A.4 Connect to Headset
A.5 Connect to Recording Device
PART B Operating the Unit.
B.1 Before Making a Call
B.2 Making Your First Call
B.3 Adjusting Your Speaker and Microphone Volume
B.4 Muting Your Calls
PART C Additional Features.
C.1 Selecting Ringtone Level and Auto-Answer
C.2 Flash Button and Flash Time Selection
C.3 Pulse/Tone Selection
C.4 Redial Your Last Call
C.5 Pause Function
C.6 Headset Hanger
3
T1 Professional Headset Telephone
Learning about the interface.
connection & preparations.
1 3
4 5
10
2
11 12 13
6 7
8 9
14
15
16
A.1 Main Switches and Interface
1. Online/Offline Button
2. LED Status-Indicator
3. Flash Key
4. Redial Key
5. Pause Key
6. Dialing Number Keys
7. Telephone Headset Jack
8. Recording Jack
9. Ringtone Selection Switch
10. Land-line Connection Jack
11. Extension-Telephone Jack
12. Flash Time Selection Switch
13. Pulse/Tone Mode Switch
14. Microphone Volume Adjustment Wheel
15. Microphone Mute Switch
16. Speaker Volume Adjustment Wheel
2
accessories & specifications
Accessories
The T1 Headset Telephone Kit should include:
1. One set of T1 Telephone
2. RJ Modular Patch Cable (land-line plug will vary according to different regions)
3. Headset Hanger (headset holder and aluminum frame)
®
4. One set of Accutone Telephone Headset (OPTIONAL)
Specifications
Power Source Telephone Line Powered
Weight - Main 200g
- Hanger 30g
Dimensions (HxWxD) - Main 37mm x 82mm x145mm
- Hanger 225mm x 93mm x 27mm
Dialing Mode Tone (DTMF) or Pulse
Amplifier Gain - Microphone 52 dB (Max)
- Receiver 31 dB (Max)
Operating Environment 5 to 40 degree Celsius
Trademark and Ownership
Accutone and the logo design combined are trademarks or registered trademarks of Accutone
Technologies Limited.
A
Hooking all the parts together! Hooking all the parts together!
54
connection & preparations. connection & preparations.
A.3 Connect to an Additional Terminal Extension
For user who requires an extra telephone extension at their terminal,
connect an extra patch cable to the Line Jack of the telephone to the (11)
Extension Telephone Jack located adjacent the (10) Land-line
Connection Jack.
A.2 Connect to Wall Jack
Use the RJ-11 Modular Patch Cable provided to connect the T1 headset
telephone to any standard Telephone Wall Jack. The connection plug to the
Wall Jack maybe different depending on your country or region. Locate the
end of the Patch Cable with the RJ-11 Modular and connect it to the (10)
Land-line Connection Jack at the bottom of the T1 unit.
®
The T1 Telephone is designed to pair with any series of Accutone
Telephone Headset, TM363VT is shown above.
First, make sure the (QD) Quick Disconnector of the headset and the
bottom cable are firmly connected as shown. Then, connect the RJ-9
Modular Jack of the headset to the (7) Telephone Headset Jack of the T1
Telephone.
A.4 Connect to Headset
connect to wall jack.
10
11
Extension Telephone Jack
Double check if the connections are
done correctly, by making a call using
either the T1 Telephone or the
Extension-Telephone just connected.
Both devices should be able to make
and receive calls.
7
QD
A.5 Connect to Recording Device
T1 is equipped with the function of
voice and call recording. Connect any
audio recording device with a 3.5mm
plug to the (8) Recording Jack
located next to the Telephone
Headset Jack of the T1 Telephone.
8
Recording Jack
T1 Professional Headset Telephone
AA
Headset Telephone in Action!
7
operating the unit.
B.3 Adjusting Your Speaker and Microphone Volume
While still in your call, you can adjust the incoming volume by using the (16)
Speaker Volume Adjustment Wheel. Turn the dial upward to increase
the speaker volume of your headset.
To adjust the outgoing volume of your microphone, turn the (14)
Microphone Volume Adjustment Wheel upward to increase the
transmission level.
Headset Telephone in Action!
6
operating the unit.
B.2 Making Your First Call
Test your T1 Telephone’s setup by making a phone call to someone. Put on
your headset and make sure it’s connected properly as illustrated in the
previous section. Please make sure you wait 10 seconds after you plug in
your telephone before making your first call.
B.1 Before Making a Call
You will need to make a call to ensure your setup in the previous section is
correct. However, before you proceed to turn on the device, make sure
the two volume control wheels are not selected to the extreme, as high
speaker volume may damage your ear and the unit, and high microphone
volume will cause loud “squealing” feedback-noise.
Press the (1) Online/Offline Button
to turn on the device and get a line.
You should be able to hear a dial-tone
and the (2) LED-Status Indicator
should light up BLUE.
Press the Online/Offline Button again
to end your call.
adjust to middle before making calls.
16
14
2
1
Make sure you DO NOT over turn
the (14) Microphone Volume
Adjustment Wheel, as this may
cause high pitched “squealing” noise
as a result of feedback.
!
WARNING
B.4 Muting Your Calls
During a call, you can mute your
microphone so that the person on
the other side of the line cannot
hear you. Mute your call by pressing
the (15) Microphone Mute
Switch.
The (2) LED-Status Indicator will
light up RED during mute.
16
14
15
2
T1 Professional Headset Telephone
BB
Learning the other functions!
additional features.
C.1 Selecting Ringtone Level & Auto-Answer
9
Select the level of the Ringtone by
a d j u s t i n g t h e ( 9 ) R i n g t o n e
Selection Switch.
Select the switch to the “H” position
for highest ringtone volume, and “L”
position for a lower ringtone volume.
Select “A” position for Auto -
Answering, so each call is immediately
answered without ringing.
C.2 Flash Button and Flash Time Selection
12
3
For some telephone system or services,
pressing the (3) Flash Key can transfer
a call to another terminal or pick
activate conference call. Different
system may have different flash time,
select (12) Flash Time Seletion
Switch for the appropriate setting.
13
Pulse/Tone Mode Switch
C.3 Pulse/Tone Selection
Select Pulse or Tone dialing depending
on y o u r preference or system
requirements by switching the (13)
Pulse/Tone Mode Switch.
Learning the other functions!
additional features.
C.4 Redial Your Last Call
User can redial their previous call by
pressing the (4) Redial Key. Please
note that on some system which
requires dialing “0” or “9” before
making a call may encounter
problems using this redial feature.
4
100, 300 or 600ms.
5
C.5 Pause Function
For telephone system or services that
supports memory redial, pressing the
(5) Pause Key will add a 2.2s delay into
the redial sequence. This feature may be
required in some VRU systems.
C.6 Headset Hanger
The T1 Telephone comes
with a handy headset hanger
for hanging the headset
when it’s not being used.
Fix the hanger to the bottom
hooks as illustrated, then
insert the (H) Headset
Holder on the top of the
hanger.
H
98
T1 Professional Headset Telephone
C C
*depending on your model
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6

Accutone T1 User Manual & Installation Manual

Brand
Accutone
Model
T1
Type
User Manual & Installation Manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents