2. Saxby
  3. Lucca MW Mini

Saxby Lucca MW Mini Instruction Leaflet

  • Hello! I am an AI chatbot trained to assist you with the Saxby Lucca MW Mini Instruction Leaflet. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
• This product is fitted with a microwave movement sensor. Please see the additional instruction leaflet for detailed
operatinginstructions.Pleasenotethatthesensorisalreadyinstalledinsidetheproduct.
•Thissystemcontainsnon-replaceablepartsandcannotbeserviced.Ifdamageoccursthepartshouldbescrapped.
Werecommendcleaningwithasoftdrycloth.
Donotusesolventsorabrasivecleanersasthesecoulddamagethefinish.
Instructionleaflet
Lucca MW Mini LED Bulkhead
77915
www.saxbylighting.com
Foryoursafety,alwaysswitchoffthesupplybeforecleaning.
Wasteelectricalproductsshouldnotbedisposedofwithhouseholdwaste.Pleaserecyclewherefacilitiesexist.
CheckwithyourLocalAuthorityorretailerforrecyclingadvice.
Recycling advice
Safety information
SaxbyLighting.BH233PE
Fitting/replacing bulbs
Iss.121082018
Microwave Movement Sensor
Thankyouforpurchasingthislightfitting.Pleasereadtheinstructionscarefullybeforeusetoensuresafeandsatisfactory
operationofthisproduct.Pleaseretaintheseinstructionsforfuturereference.
Warning
Layout
• Planthedesiredlayoutofthisfittingcarefully,ensuringthecableswillreachthedistancebetweenthejunctionboxand
thelightfitting.
• Avoidlocatinganycablesinpositionsthatwouldcauseahazard.Positioncablesandjunctionboxes(notsupplied)
awayfromareaswheretheymaybeatriskfrombeingcut,trappedordamaged.
• Themainssupplycablemusthaveaminimumcrosssectionalareaof1.0mm².
• Cablesmustbeprotectedusingsuitableconduitorplastictrunking.
• Theproductscanbewallorceilingmounted.Ifwallmountingensurethatthepowersupplyisatthebottom.
Existingfittingsmustbecompletelyremovedbefore
installationofanewproduct.Beforeremovingtheexisting
fitting,carefully note the position of each set of wires.
• Gentlypullthecasingawayfromtheshadeandset
aside.
• Removethe4fixingscrewsanddetachtheshade.Keep
safeforrefittinglater.
• Holdtheproductinplaceandmarkthepositionofthe
holes.Ensurethewalliscapableofholdingtheweight
oftheproduct,oriffittingtoaceiling,ensurethereis
ajoistatthepointoffixingtosupporttheweightofthe
product.
• Knockoutthechosenfixingholes
• Fixintoposition.Takecaretoavoiddamagingany
concealedwiringandpipes.Thecorrectfixingsshould
beusedforbrick,cavitywallsorplasterboard.
• Pierceaholeinthegrommet,andpullthecable
through.
• Wireasdetailedbelow
Installation
This product is Class 2 (Double insulated)
and must not be earthed.
Please read these instructions carefully before
commencing any work.
This unit must be fitted by a competent and qualified
electrician.
Install in accordance with IEE Wiring regulations and
current Building Regulations.
To prevent electrocution switch off at mains supply
before installing or maintaining this fitting. Ensure
other persons cannot restore the electrical supply
without your knowledge. If you are in any doubt,
please consult a qualified electrician.
This light fitting should be connected to a circuit with a
30mA RCD fitted.
If replacing an existing fitting, make a careful note of
the connections.
This product contains non-replaceable parts and
cannot be serviced. If damage occurs the part should
be scrapped.
Waste electrical products should not be disposed of
with household waste. Please recycle where facilities
exist. Check with your local authority or retailer for
recycling advice.
This product is rated at IP65.
Specification
Voltage: 240V~50Hz
Lamp: 17WLEDModule-4200K
IPrating: 65
• Ensurethatthescrewsandcableentrypointsaresealed
tomaintaintheIPratingoftheproduct.
• Refit the shade, ensuring that the seals are correctly
located.
• Gently pushthe casing onto the shade until it clips in
place.
• Replacefuseorcircuitbreakerandswitchon.Yourlight
isnowreadyforuse.
Commissioning
Wiring
Check that...
• Thisproductisdoubleinsulatedandmustnotbeearthed.Ifthereareanyincomingearthcables,theymustbeterminated
inthespareterminaloftheconnectionblock.Havingcorrectlyidentifiedthewiringfromyourexistinglightfitting,connect
tothequickfitconnectionblockinthefollowingway:
• Youhavecorrectlyidentifiedthewires.
• Theconnectionsaretight.
• Noloosestrandshavebeenleftoutoftheconnectionblock.
INSERT CABLE
PUSH DOWN
EARTH (TO TERMINATE)
/