2. Saxby
  3. 60895

Saxby 60895 Instruction Leaflet

  • Hello! I am an AI chatbot trained to assist you with the Saxby 60895 Instruction Leaflet. I’ve already reviewed the document and can help you find the information you need or explain it in simple terms. Just ask your questions, and providing more details will help me assist you more effectively!
• Push the labelled male and female connectors
togethertopowerthedemisterpad.
• Refitthemirrorfrontontothewallback.Ensurethat
the seals are correctlylocated before securingwith
thefourscrews.
• Replacefuse or circuit breakerand switchon. Your
lightisnowreadyforuse.
• ActivateyournewLEDmirrorbyswipingyourhandin
frontofthesensor.
Commissioning
Instructionleaflet
Rift Mirror
60895
www.saxbylighting.com
Wasteelectricalproductsshouldnotbedisposedofwithhouseholdwaste.Pleaserecyclewherefacilities
exist.CheckwithyourLocalAuthorityorretailerforrecyclingadvice.
Recycling advice
Safety information
SaxbyLightingBH233PE
• Werecommendcleaningwithasoftdrycloth.Do
notusesolventsorabrasivecleanersasthesecould
damagethefinish.
• Mirror–Useadampclothoraproprietyglass
cleaner.Donotuseabrasivematerialsasthesewill
damagethefinish.
Live Voltages may be present in this unit even when turned of or when completely disconnected.Foryoursafety,
alwaysswitchoffthesupplybeforechanginglightbulbs,orcleaning.
The mirror must be replaced immediately should it become cracked or damaged. This fitting must
not be used without the mirror in place.
• The shaver socket is powered by a 20W isolating
transformerandisonlyintendedforusewithelectric
shavers, electric toothbrush chargers and similar
products.
• Any appliance connected to the socket must not
exceed the 20W power output as this could cause
damageandoverheatingtooccur.
• Always check your appliance instructionstoensure
thepowerrequirementsarelessthan20W.
• Simplyturnonthedemisterswitchontheside.The
demisterpadwillwarmthemirrorsurface.
• The demisting effect will spread approximately 10-
20%furtherthanthepaditself.
Shaver Socket Instructions
Demister Operation
Iss.108072015
Thankyouforpurchasingthislightfitting.Pleasereadtheinstructionscarefullybeforeusetoensuresafeand
satisfactoryoperationofthisproduct.Pleaseretaintheseinstructionsforfuturereference.
Warning
This is a Class 1 product and must be earthed
Pleasereadtheseinstructionscarefullybefore
commencinganywork.
Thisunitmustbefittedbyacompetentandqualified
electrician.
InstallinaccordancewithIEEWiringregulationsand
currentBuildingRegulations.
Topreventelectrocutionswitchoffatmainssupply
beforeinstallingormaintainingthisfitting.Ensure
otherpersonscannotrestoretheelectricalsupply
withoutyourknowledge.
Thislightfittingshouldbeconnectedtoafusedcircuit.
Ifreplacinganexistingfitting,makeacarefulnoteof
theconnections.
Thissystemcontainsnon-replaceablepartsand
cannotbeserviced.Ifdamageoccursthepartshould
bescrapped.
Thisproductisnotsuitablefordimming.
ThisproductisratedatIP44.
Thisproductcontainsademisterpad.Ifthispadis
damagedinanywaythenitshouldbereplacedbya
qualifiedelectrician.
Wasteelectricalproductsshouldnotbedisposedof
withhouseholdwaste.Pleaserecyclewherefacilities
exist.Checkwithyourlocalauthorityorretailerfor
recyclingadvice.
Specification
Voltage: 240V50Hza.c.
Lamp: 2x1.5WLED(Capsule)Coolwhite&5.5WLED(SMD2835)CoolWhite
IPrating: 44
Shaversocket:115V-240Vdualsocket
Layout
• Cablesinwallsmustbeprotectedusingsuitable
conduitorplastictrunking.
• Themainssupplycablemusthaveaminimumcross
sectionalareaof1.0mm².
• Thisproducthasspecialprotectionagainstthe
ingressofmoistureandisIP44rated.
• Thisproductisfittedwithanotouchinfra-
redswitch,helpingtokeepthemirrorclearof
fingerprints.Wheninstallingtheproduct,thesensor
switchmustbeatleast150mmfromanadjacent
wallorobstructiontoensuretheswitchcanfunction
properly.
Existingfittingsmustbecompletelyremovedbefore
installationofanewproduct.Beforeremovingthe
existingfitting,carefully note the position of each set
of wires.
• Undothescrews(twooneachsideofthefitting)
andremovethefrontmirrorassemblyandsetaside.
• Holdthebackplateinplaceandmarkthepositionof
thefixingholes.Ensurethattheproductislevel.
• Ensurethewalliscapableofholdingtheweightofthe
product.Takecaretoavoiddamaginganyconcealed
wiringandpipes.Thecorrectfixingsshouldbeused
forbrick,cavitywallsorplasterboard.
• Piercegrommetandpassthesupplycablethrough
theholeinthewallback.
• Fixtheproductintoposition.
Installation
Havingcorrectlyidentifiedthewiringfromyourexisting
lightfitting,connecttotheconnectionblockinsidethe
productinthefollowingway:
Wiring
Check that...
• Youhavecorrectlyidentifiedthewires
• Theconnectionsaretight
• Noloosestrandshavebeenleftoutoftheconnection
block.
ThisproductissuitableforuseinZone
2andoutsideZonesofabathroom.
Seediagram.Ifthisunitisbeing
fittedinaroomcontainingabathor
shower,a30mARCDmustbeused,
inaccordancewithIEEregulations.
/