Saxby 61522 Instruction Leaflet

Brand: Saxby

Model: 61522

Type: Instruction Leaflet

• Replacefuseor circuit breakerand switch on.Your

lightisnowreadyforuse.

• TheLEDmoduleinthisproductisnon-replaceable.

Commissioning

Fitting/replacing bulbs

Instructionleaflet

Cora & Bari Track Spotlights

61522,61523

www.saxbylighting.com

Foryoursafety,alwaysswitchoffthesupplybeforechanginglightbulbs,orcleaning.

Wasteelectricalproductsshouldnotbedisposedofwithhouseholdwaste.Pleaserecyclewherefacilities

exist.CheckwithyourLocalAuthorityorretailerforrecyclingadvice.

Recycling advice

Safety information

SaxbyLightingLtd.BH233PE

Werecommendcleaningwithasoftdrycloth.

Donotusesolventsorabrasivecleanersasthesecould

damagethefinish.

Iss.226012016

Fitting the spotlight units

• Tofitthespotlightunits,slidethetabdown,androtatetheproduct90

• degreestoengagetheconnectionsinthetrack.

• Allowthetabtoslidebackupandensurethatitislocatedcorrectlyin

• thetrackslot.

Tab

Rotate 90

Thankyouforpurchasingthislightfitting.Pleasereadtheinstructionscarefullybeforeusetoensuresafeand

satisfactoryoperationofthisproduct.Pleaseretaintheseinstructionsforfuturereference.

Warning

This is a Class 1 product and must be earthed.

Pleasereadtheseinstructionscarefullybefore

commencinganywork.

Thisunitmustbefittedbyacompetentandqualified

electrician.

InstallinaccordancewithIEEWiringregulationsand

currentBuildingRegulations.

Topreventelectrocutionswitchoffatmainssupply

beforeinstallingormaintainingthisfitting.Ensure

otherpersonscannotrestoretheelectricalsupply

withoutyourknowledge.Ifyouareinanydoubt,

pleaseconsultaqualifiedelectrician.

Thislightfittingshouldbeconnectedtoafusedcircuit.

Ifreplacinganexistingfitting,makeacarefulnoteof

theconnections.

Thissystemcontainsnon-replaceablepartsand

cannotbeserviced.Ifdamageoccursthepartshould

bescrapped.

Wasteelectricalproductsshouldnotbedisposedof

withhouseholdwaste.Pleaserecyclewherefacilities

exist.Checkwithyourlocalauthorityorretailerfor

recyclingadvice.

Thisproductisnotsuitablefordimming.

Specification

Voltage: 240V50Hza.c.

Lamp: 7WLEDModule(COB)NaturalWhite-629lm

IPrating: 20

Layout

Existingfittingsmustbecompletelyremovedbefore

installationofanewproduct.Beforeremovingthe

existingfitting,carefully note the position of each set

of wires.

• Usingtheceilingcoverasatemplate,markthefirst

holepositionandfitthescrewinpositionasshown

below.Ensuretheceilingiscapableofholdingthe

weightofthetrackandproducts.Takecaretoavoid

damaginganyconcealedwiringandpipes.The

correctfixingsshouldbeusedforbrick,cavitywalls

orplasterboard.

• Feedthescrewthroughthekeyholeslot,andslide

intoposition.Markthepositionofthesecondhole.

Locatethetrackandfitthesecondscrewinto

position.

• Wireasdetailedbelow.

Installation

Wiring

Check that...

• Youhavecorrectlyidentifiedthewires.

• Theconnectionsaretight.

• Noloosestrandshavebeenleftoutoftheconnection

block.

• Planthedesiredlayoutofthisfittingcarefully,

ensuringthecableswillreachthedistancebetween

thejunctionboxandthelightfitting.

• Avoidlocatinganycablesinpositionsthatwould

causeahazard.Positioncablesandjunctionboxes

(notsupplied)awayfromareaswheretheymaybe

atriskfrombeingcut,trappedordamaged.

• Themainssupplycablemusthaveaminimumcross

sectionalareaof1.0mm².

Havingidentifiedthehouseholdwiringfromyourexistinglightfitting,connecttotheconnectionblockinsidetheproduct

inthefollowingway:

• Undothescrewandremovethecoverfromtheliveend.

• Pushoutthedesiredcableaccesspoint.

• Identifythecorrectcablefromthesupplyandpullthrough.

• Connectthesupplywirestotheterminalblock,oppositethe

• correspondingwiresfromthefitting.Thecentralconnector

• canalsobewiredinthisway.

• Refitthecoverontotheliveendtakingcarenottotrapthecable.

Supply

Fitting an additional track

• Theseproductsaresuppliedwithastraightconnector

thatenablesthefittingofanadditionaltrack.Theconnector

hasearthconnectionpointsonbothsides

• Verifywhichtabneedstoberemovedwhenofferingthe

• connectorto thetrack.Toremove the tab,grasp firmly

with a pair of pliers and lever back. The tab should snap

cleanly.

• Locatetheconnectorinthetrackandpushhome. Remove One

or Other Tab

Marked in Grey

End view of track

Earth

Conductor

Remaining Earth tab needs to

be inserted into Earth conductor

to ensure Earth continuity.

Spotlightsgiveaconcentratedbeamoflightandmustnotbepositionedanycloserthan0.5M

(50cm)totheilluminatedsurface.

Saxby 61522 Instruction Leaflet

Saxby 61522 Instruction Leaflet

Saxby 61522 Instruction Leaflet

Related papers

Other documents