Square Stand User manual

Brand: Square

Model: Stand

Type: User manual

This manual is also suitable for

Stand / Card Reader

Square Stand is an all-in-one solution for businesses that want to accept payments and manage their sales. It allows you to swipe cards, accept contactless and chip payments, and print receipts. Square Stand also has a built-in hub that allows you to connect other accessories, such as a barcode scanner or cash drawer. With its sleek design and easy-to-use interface, Square Stand is a great choice for businesses of all sizes.

Square Stand

Getting Staed

WHAT’S IN THE BOX

Let’s get you up and running. Everything you need to sta selling is in the box—just make sure you have your compatible iPad ready.

Square Reader

for contactless and chip

Dock for Square Reader Square Stand Power adapter cable

Power adapter USB hardware hub Drill mount

Adhesive mount

SETTING UP SQUARE STAND

Sta by connecting Square Stand to the hardware hub and power adapter. You can then connect your Square Reader and Dock to the hardware hub.

Connect Square Stand to

the hardware hub

The hardware hub has two

cables: one that connects to

the bottom of Square Stand

and one that connects to the

power adapter.

Connect the hardware

hub to the power adapter

Plug the hardware hub into

the power adapter, then

connect the power adapter

cable to the power adapter.

Plug into an outlet

Plug the power adapter cable

into a power outlet.

Slide Square Reader

into Dock

Remove the retainer clip

from Dock. Slide Square

Reader into Dock’s micro

USB connector. Replace

the retainer clip.

Plug in Dock

Plug Dock for Square Reader

into the hardware hub.

Learn how to connect other

accessories on the next page.

Insert your iPad into

Square Stand

Pull out the security pin on

the left side of Stand. Place

your iPad into Stand and

connect your iPad to the

Lightning connector. Push the

security pin into the headset

jack of your iPad to secure it

to Stand. Open the Square

app on your iPad, follow the

onscreen instructions, and

you’re ready to sta selling.

MANAGING YOUR ACCESSORIES AND IPAD

Removing your iPad

If you need to remove your iPad from Stand, remove the

security pin from the headset jack of your iPad, then press

the eject button located on the back of Stand.

Taking payments without a power source

When Stand isn’t plugged into a wall (and is just powered by

your iPad), you can swipe magstripe cards and connect to

Square Reader via Bluetooth to accept contactless and chip

payments.

Accessories

Plug any optional USB accessories into the hardware

hub, such as a bar code scanner, receipt printer, or

cash drawer. Some accessories may need you to

ﬁnish setup by going to Settings > Hardware

in the Square app.

Eject button

Need help? Get the full guide at square.com/taking-payments.

TAKING PAYMENTS

Square Stand lets you swipe cards with the built-in magstripe reader, and accept contactless and chip payments with the included Square Reader.

Dip

In the Square app, tap Charge and wait for a single green

light to appear on Square Reader. Your customer can then

inse a chip card into the reader. Leave it in place until you

see four green lights.

Tap

In the Square app, tap Charge and wait for a single green light

to appear on Square Reader. Your customer can then hold a

contactless device or card near the reader to trigger payment.

Swipe

In the Square app, tap Charge. Run your customer’s

magnetic-stripe card through the magstripe reader on

Square Stand.

ADHESIVE MOUNT (OPTION 1)

Secure Stand to your counter with the included adhesive mounting plate.

Plug the hardware hub into Stand

Plug the cable from the hardware hub into

the bottom of Stand. Note: If the cable exits

the base of Stand on the right side (when

the screen faces you), Stand will swivel

clockwise. If the cable exits the base on the

left side, Stand will swivel counterclockwise.

Screw in the adhesive mounting plate

Make sure the hardware hub cable is ﬁrmly

pushed in, then screw in the adhesive

mounting plate.

Remove the adhesive backing

Check that the plate is tightly screwed in

and the base of Stand is locked with the

cable exiting from your preferred side, then

remove the adhesive backing.

Mount Stand to your countertop

Clean and dry the area where you want to

mount Stand, then ﬁrmly adhere Stand into

place. Press down for 30 seconds and wait

30 minutes for the adhesive to set.

Note: To remove the adhesive mount, pull the tabs on the mount slowly outwards. The adhesive will sta to stretch until it detaches from the suace it was mounted on.

DRILL MOUNT (OPTION 2)

Secure Stand to your counter with a drill and the included drill mount.

Drill the hole for the drill mount

With a 3/16" drill bit, drill a hole into your

counter. Make sure your bit will work on

your counter material.

Plug the hardware hub into Stand

Plug the cable from the hardware hub into

the bottom of Stand. Note: If the cable exits

the base of Stand on the right side (when

the screen faces you), Stand will swivel

clockwise. If the cable exits the base on the

left side, Stand will swivel counterclockwise.

Line up Stand with the drill hole

Line up the screw hole in the base of Stand

with the hole in your counter. Double-check

that the base of Stand is locked with the

cable exiting from your preferred side.

Mount Stand to your counter

Screw the drill mount into the base of Stand

through the bottom of your counter. Turn the

nut until it’s ﬁrmly against the bottom of your

counter. Make sure the drill mount and Stand

are secure and Stand can only swivel on a

180-degree axis.

HELP AND SUPPORT

Read our FAQs, learn more about compatible hardware, and get troubleshooting suppo at square.com/hardware-setup.

HARDWARE PROTECTION

If something goes wrong with your Square hardware, you’re covered for up to one year. Go to square.com/returns so we can make things right.

FREE 30-DAY RETURNS

Square guarantees a 30-day, risk-free return policy for all purchases made from square.com/shop. After a return is complete, a refund will be credited back to you.

REGULATORY INFORMATION

View regulatory and FCC information for Square Stand by opening the Square app and going to Suppo > Legal > Regulatory.

Your use of the Square app, Dock for Square Reader, Square Reader for contactless and chip, and Square Stand, including any warranties associated with these products, is governed by your agreements

with Square and related policies available at square.com/legal. © 2020 Square, Inc. Square, the Square logo, Square Reader, and Square Stand are trademarks of Square, Inc. iPad, iPad Air, and iPad Pro are

trademarks of Apple Inc., registered in the U.S. and other countries. App Store is a service mark of Apple Inc. Other marks and brands are the propey of their respective owners.

Square Stand, Square Reader, and Dock for Square Reader

This device complies with pa 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful inteerence, and (2) this device must accept any inteerence

received, including inteerence that may cause undesired operation.

NOTE: The grantee is not responsible for any changes or modiﬁcations not expressly approved by the pay responsible for compliance. Such modiﬁcations could void the user’s authority to operate the

equipment.

IMPORTANT NOTE: FCC RF Radiation Exposure Statement: This equipment complies with FCC RF radiation exposure limits set foh for an uncontrolled environment. This equipment should be installed

and operated with a minimum distance of 20 cm between the radiator and any pa of your body.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to pa 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful inteerence in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may

cause harmful inteerence to radio communications. However, there is no guarantee that inteerence will not occur in a paicular installation. If this equipment does cause harmful inteerence to radio or

television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the inteerence by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.