FSR FL-500P-SLD-ALM-C U-Cover User manual

FSR
Brand
FSR
Model
FL-500P-SLD-ALM-C U-Cover
Type
User manual
FSR 244 Bergen Boulevard, Woodland Park, NJ 07424, Phone: 973.785.4347 - Fax: 973.785.4207
43200 LIT1332B
BOX INSTALLATION - STEP 1
LOCATE AND POSITION BOX IN ACCORDANCE WITH FLOOR
PLANS. TOP SURFACE OF TEMPORARY COVER MUST BE SET
TO MATCH THE HEIGHT OF THE FINISHED FLOOR - ie STONE,
WOOD OR CONCRETE - SEE TYPICAL INSTALLATION HEIGHTS.
LEVEL AND ANCHOR BOX AS REQUIRED. USE SCREWS, NAILS,
OR WIRE TO PREVENT BOX FROM FLOATING DURING POUR.
REMOVE AND RETAIN TEMPORARY COVER AND SCREWS.
ROUTE CONDUITS TO BOX AS REQUIRED. GANG BRACKET
SCREWS MUST BE IN PLACE AND BOTTOMED TO ENSURE
SCREW VOIDS AFTER POUR. PLACE THIS INSTALLATION GUIDE
BACK INTO BOX, ALONG WITH ALL SUPPLIED ITEMS, AND
REINSTALL TEMPORARY COVER.
BOX INSTALLATION - STEP 2
SCREED TO TOP OF BOX SURFACE FOR 3/16" THICK
CARPET/FLOORING OR SPECIFIC HEIGHT TO ALLOW
FOR THICKER FINISHED FLOOR MATERIAL. HAND
TROWELING RECOMMENDED NEAR BOX EDGES.
BOX HAS NO HEIGHT ADJUSTMENT AFTER
CONCRETE POUR.
TEMPORARY
COVER
(8) #6-32 FLAT HEAD SCREW
CONCRETE SURFACE OR TOP
OF FINISHED FLOOR MATERIAL
Carpeted or Tile Floors, Cover types - BLP, BSQ, B, SLP, SSQ, S
TYPICAL INSTALLATION HEIGHTS
(4) LEVELING BOLT
FL-500P INSTALLATION INSTRUCTIONS
INSTALLING ELECTRONIC COMPONENTS
PULL WIRES AND CABLES TO BOX AS NECCESSARY (REMOVAL OF
GANG MOUNTING BRACKETS MAY BE REQUIRED). TERMINATE
WIRES AND CABLES TO ELECTRONIC COMPONENTS, AND INSTALL
ELECTRONIC COMPONENTS ONTO GANG MOUNTING BRACKETS.
REINSTALL TEMPORARY COVER IF FINISHED COVER IS TO BE
INSTALLED AT A LATER DATE.
INSTALLED
ELECTRONIC
COMPONENT
GANG
MOUNTING
BRACKET
(2) #8-32 x .25 LG
FLAT HEAD
SCREW
DIVIDER ASSEMBLY
GANG
MOUNTING
PLATE
(2) #8-32 x .375 LG
SELF TAPPING
PAN HEAD
SCREW
GANG PLATE ASSEMBLY
GANG DIVIDER ASSEMBLY
4" BOX DIVIDER 5"-6" BOX DIVIDER 7"-12" BOX DIVIDER
(2) #8-32 x .25 LG
PAN HEAD
SCREW
DIVIDER HOLDER
DIVIDER
(2) #8-32 x .25 LG
PAN HEAD
SCREW
DIVIDER HOLDER
DIVIDER
DIVIDER HOLDER
(2) #8-32 x .25 LG
PAN HEAD
SCREW
DIVIDER
Vinyl or Stained Concrete, Cover types - BK, SS, BRS
DIVIDER HOLDER MUST BE ORIENTED AS SHOWN WHEN ATTACHING
TO DIVIDERS, IN ORDER TO PROPERLY ASSEMBLE BOX INTERIOR.
* DIVIDER ASSEMBLY FOR 5" & 7" BOXES
POSITION DIVIDER ASSEMBLY IN BOX BEFORE INSTALLING
GANG PLATE ASSEMBLY. SECURE DIVIDER ASSEMBLY TO
GANG PLATE ASSEMBLY WITH SCREWS AS NOTED.
(FOR USE WITH FL-500P SERIES COVERS ONLY)
CONCRETE
TEMPORARY
COVER
FLOOR BOX
SCREED FLUSH
COVER FLUSH WITH CONCRETE
(FOR 1/8" THICK COVER) CARPET FLOORING
CONCRETE
CARPET 1/8" THICK
COVER WITH
EDGING
FLOOR BOX
TILE OR LAMINATE FLOORING
CONCRETE
FINISHED
FLOOR 1/8" THICK
COVER WITH
EDGING
FLOOR BOX
VINYL FLOORING STAINED FLOORING
CONCRETE
SCREED FLUSH
FLOOR BOX
TEMPORARY
COVER
COVER FLUSH WITH CONCRETE
(FOR 1/8" THICK COVER)
CONCRETE
FINISHED
FLOOR
FLOOR BOX
1/8" THICK COVER
SHIM TO VINYL
THICKNESS
CONCRETE
1/8" THICK COVER
FLOOR BOX
FLOOR BOX TEMPORARY COVER WILL EITHER BE INSTALLED DIRECTLY ON THE BOX OR SHIMMED
BASED ON THE COVER AND FLOORING SPECIFICATIONS. SHIM KITS SOLD SEPARATELY (FL-500P-CSK).
THE TEMPORARY COVER MAY NOT BE FLUSH WITH THE FINISH FLOOR IN ALL INSTALLATIONS.
1-GANG/2-GANG CONFIGURATION 1-GANG/3-GANG CONFIGURATION
2-GANG/2-GANG CONFIGURATION 3-GANG/1-GANG CONFIGURATION
4-GANG CONFIGURATION
GANG MOUNTING BRACKET CONFIGURATION
PER CUSTOMER SPECIFICATIONS, CONFIGURE GANG MOUNTING BRACKETS AS SHOWN BELOW AND
REASSEMBLE INTO BOX (DECORA WALL PLATES SHOWN AS REFERENCE AND NOT INCLUDED).
COVER PLATE
GANG
MOUNTING
BRACKET
OPTIONAL DIVIDER
GANG
MOUNTING
BRACKET
OPTIONAL DIVIDER
GANG MOUNTING BRACKET
OPTIONAL
DIVIDER
GANG MOUNTING BRACKET
OPTIONAL DIVIDER
DIVIDER
HOLDER
DIVIDER
HOLDER
DIVIDER
HOLDER
(2) DIVIDER
HOLDER
GANG MOUNTING BRACKET
(2) DIVIDER HOLDER
(NO DIVIDERS USED)
REMOVABLE LARGE CENTER DIVIDER
REMOVABLE SMALL
CENTER DIVIDER
REMOVABLE SMALL
CENTER DIVIDER
REMOVABLE LARGE CENTER DIVIDER
CENTER DIVIDER CONFIGURATION (NOT APPLICABLE ON 4" BOX)
SET ASIDE TEMPORARY COVER AND SCREWS FOR POSSIBLE RE-INSTALLATION.
REMOVE AND RETAIN GANG MOUNTING BRACKETS AND SCREWS TO CONFIGURE
CENTER DIVIDERS.
Vinyl or Stained Concrete, Cover types - SLD-ALM, SLD-Color
Wood / Floating Wood, Cover types - BK, SS, BRS (1/8"), SLD-ALM, SLD-Color (3/8")
Wood / Floating Wood, Cover types - BLP, BSQ, B, SLP, SSQ, S
POSSIBLE GANG DIVIDER LOCATION BOTH GANG MOUNTING BRACKETS ARE IDENTICAL, AS IS THEIR CONFIGURATION CAPABILITY
COVER FLUSH WITH CONCRETE
(FOR 3/8" THICK COVER) VINYL FLOORING STAINED FLOORING
CONCRETE
FINISHED
FLOOR 3/8" THICK COVER
SHIM TO VINYL
THICKNESS
FLOOR BOX CONCRETE FLOOR BOX
3/8" THICK COVER
CONCRETE
TEMPORARY
COVER
SHIM 1/4"
FLOOR BOX
SCREED FLUSH
CONCRETE FLOOR BOX
TEMPORARY
COVER
1/4" (SEE NOTE)
FINISHED
FLOOR
CONCRETE
FINISHED
FLOOR 1/8" THICK
COVER
FLOOR BOX
SLEEPER
SYSTEM
(IF USED) CONCRETE SLEEPER
SYSTEM
(IF USED)
FLOOR BOX
FINISHED
FLOOR 3/8" THICK
COVER
COVER ABOVE CONCRETE
(FOR COVER WITHOUT EDGING) WOOD FLOORING WOOD FLOORING
CONCRETE
EDGING
HEIGHT
FLOOR BOX
TEMPORARY COVER
FINISHED
FLOOR
FINISHED FLOOR
CONCRETE SLEEPER SYSTEM (IF USED)
1/8" THICK COVER
WITH EDGING
FLOOR BOX
COVER ABOVE CONCRETE
(FOR COVER WITH EDGING) WOOD FLOORING
FOR 3/8" THICK COVER LOWER TEMPORARY
COVER AN ADDITIONAL 1/4" FROM FINISHED
FLOOR DIMENSION OR USE SHIM KIT
NOTE:
TYPICAL INSTALLATION HEIGHTS FLOOR BOX TEMPORARY COVER WILL EITHER BE INSTALLED DIRECTLY ON THE BOX OR SHIMMED
BASED ON THE COVER AND FLOORING SPECIFICATIONS. SHIM KITS SOLD SEPARATELY (FL-500P-CSK).
THE TEMPORARY COVER MAY NOT BE FLUSH WITH THE FINISH FLOOR IN ALL INSTALLATIONS.
  • Page 1 1
  • Page 2 2

FSR FL-500P-SLD-ALM-C U-Cover User manual

FSR
Brand
FSR
Model
FL-500P-SLD-ALM-C U-Cover
Type
User manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents