FSR FL-605P-6-B Installation guide

Brand: FSR

Model: FL-605P-6-B

Type: Installation guide

FSR 244 Bergen Boulevard, Woodland Park, NJ 07424, Phone: 973.785.4347 - Fax: 973.785.4207

43027 LIT1433

BOX INSTALLATION - STEP 1

LOCATE AND POSITION BOX IN ACCORDANCE WITH FLOOR

PLANS. TOP SURFACE OF TEMPORARY COVER MUST BE SET

TO MATCH THE HEIGHT OF THE FINISHED FLOOR - ie STONE,

WOOD OR CONCRETE - SEE TYPICAL INSTALLATION HEIGHTS.

LEVEL AND ANCHOR BOX AS REQUIRED. USE SCREWS, NAILS,

OR WIRE TO PREVENT BOX FROM FLOATING DURING POUR.

REMOVE AND RETAIN TEMPORARY COVER AND SCREWS.

ROUTE CONDUITS TO BOX AS REQUIRED. GANG BRACKET

SCREWS MUST BE IN PLACE AND BOTTOMED TO ENSURE

SCREW VOIDS AFTER POUR. PLACE THIS INSTALLATION GUIDE

BACK INTO BOX, ALONG WITH ALL SUPPLIED ITEMS, AND

REINSTALL TEMPORARY COVER.

BOX INSTALLATION - STEP 2

SCREED TO TOP OF BOX SURFACE FOR 3/16" THICK

CARPET/FLOORING OR SPECIFIC HEIGHT TO ALLOW

FOR THICKER FINISHED FLOOR MATERIAL. HAND

TROWELING RECOMMENDED NEAR BOX EDGES.

BOX HAS NO HEIGHT ADJUSTMENT AFTER

CONCRETE POUR.

TEMPORARY

COVER

(8) #6-32 FLAT HEAD SCREW

CONCRETE SURFACE OR TOP

OF FINISHED FLOOR MATERIAL

CARPET OVER CONCRETE (COVER WITH BEVELED EDGING)

TYPICAL INSTALLATION HEIGHTS

(4) LEVELING BOLT

FL-605P INSTALLATION INSTRUCTIONS

INSTALLING ELECTRONIC COMPONENTS

PULL WIRES AND CABLES TO BOX AS NECCESSARY (REMOVAL OF

GANG MOUNTING BRACKETS MAY BE REQUIRED). TERMINATE

WIRES AND CABLES TO ELECTRONIC COMPONENTS, AND INSTALL

ELECTRONIC COMPONENTS ONTO GANG MOUNTING BRACKETS.

REINSTALL TEMPORARY COVER IF FINISHED COVER IS TO BE

INSTALLED AT A LATER DATE.

INSTALLED

ELECTRONIC

COMPONENT

GANG

MOUNTING

BRACKET

(2) #8-32 x .25 LG

FLAT HEAD

SCREW

DIVIDER ASSEMBLY

GANG

MOUNTING

PLATE

(2) #8-32 x .375 LG

SELF TAPPING

PAN HEAD

SCREW

GANG PLATE ASSEMBLY

GANG DIVIDER ASSEMBLY

(2) #8-32 x .25 LG

PAN HEAD

SCREW DIVIDER HOLDER

DIVIDER

TILE OR THIN WOOD LAMINATE OVER CONCRETE (COVER WITH SQUARE EDGING)

CONCRETE

FLOOR BOX

TEMPORARY COVER

CARPET EDGING

FINISH COVER

FLOOR BOX

CONCRETE

FLOOR BOX

TEMPORARY COVER

TILE OR THIN WOOD LAMINATE

CONCRETE

EDGING

FINISH COVER

FLOOR BOX

SCREED FLUSH

SCREED FLUSH GROUT/THINSET

DIVIDER HOLDER MUST BE ORIENTED AS SHOWN WHEN ATTACHING

TO DIVIDERS, IN ORDER TO PROPERLY ASSEMBLE BOX INTERIOR.

DIVIDER

HOLDER USED

AS SMALL GAP

FILLER*

LARGE GAP

FILLER*

* GAP FILLERS ARE OPTIONAL, PER DESIRED

CONFIGURATION (SEE PREVIOUS PAGE),

AND ARE INSTALLED SIMILARLY TO

DIVIDER ASSEMBLIES.

* DIVIDER ASSEMBLY FOR 6" BOXES

POSITION DIVIDER ASSEMBLY IN BOX BEFORE INSTALLING

GANG PLATE ASSEMBLY. SECURE DIVIDER ASSEMBLY TO

GANG PLATE ASSEMBLY WITH SCREWS AS NOTED.

GANG MOUNTING BRACKET CONFIGURATION

PER CUSTOMER SPECIFICATIONS, CONFIGURE GANG MOUNTING BRACKETS AS

SHOWN BELOW AND REASSEMBLE INTO BOX.

REMOVABLE LARGE CENTER DIVIDER

REMOVABLE SMALL CENTER DIVIDER

REMOVABLE LARGE CENTER DIVIDER

CENTER DIVIDER CONFIGURATION.

SET ASIDE TEMPORARY COVER AND SCREWS FOR POSSIBLE RE-INSTALLATION.

REMOVE AND RETAIN GANG MOUNTING BRACKETS AND SCREWS TO CONFIGURE

CENTER DIVIDERS.

TYPICAL INSTALLATION HEIGHTS

WOOD WITH OR WITHOUT SLEEPER SYSTEM OVER CONCRETE (COVER WITH EDGING)

TEMPORARY COVER

FLOOR BOX

CONCRETE

CONCRETE FLOOR BOX

FINISH COVER

EDGING

WOOD

H (BASED ON ASSEMBLY THICKNESS) =

TH (TOTAL ASSEMBLY HEIGHT) - E (EDGING HEIGHT)

WOOD WITH OR WITHOUT SLEEPER SYSTEM OVER CONCRETE (COVER WITHOUT EDGING)

H = ASSEMBLY THICKNESS

TEMPORARY COVER

FLOOR BOX

CONCRETE

WOOD

CONCRETE

FLOOR BOX

FINISH COVER

VINYL FLOORING OVER CONCRETE (COVER WITHOUT EDGING)

CONCRETE

TEMPORARY COVER

FLOOR BOX CONCRETE FLOOR BOX

FINISH COVER

VINYL FLOORING

SLEEPER

SYSTEM

(IF USED)

SLEEPER

SYSTEM

(IF USED)

VERIFY PER

SPECIFICATION

OR ORDER

POSSIBLE GANG DIVIDER LOCATION

6 GANG MOUNTING PLATE

DIVIDER HOLDER

OPTIONAL DIVIDER

LARGE GAP FILLER

DIVIDER HOLDER USED

AS SMALL GAP FILLER

"6 GANG SIDE" MOUNTING BRACKET CONFIGURATIONS

1G 3G 1G 3G

2G 2G 2G 2G

1G 4G

2G 3G 3G 1G

2G 2G

3G 2G 4G 1G 6G

FSR FL-605P-6-B Installation guide

FSR FL-605P-6-B Installation guide

FSR FL-605P-6-B Installation guide

Related papers

Other documents