Antsig AP700 Installation guide

Brand: Antsig

Model: AP700

Type: Installation guide

Antsig AP700 is a VHF/UHF masthead amplifier designed to amplify TV signals received by your antenna, providing up to 30dB of gain. It's ideal for weak signal areas or when using multiple TVs. Connect your antenna to the head unit and the output to your TV or receiver. The power supply unit plugs into a mains outlet and provides power to the amplifier. A yellow light indicates that the amplifier is powered on. If the light is red, there is a short circuit on the input connection.

VHF/UHF Masthead Ampliﬁer

Model: AP700

Thanks for purchasing this AP700 Masthead Ampliﬁer.

Before installation,

Please read this manual carefully and keep this manual

for further information.

APPLICATIONS

• For effective ampliﬁcation of the TV signal received by TV antenna(s) (approximately 30dB)

• Use in weak TV signal areas or for multiple TVs

• Use with individual VHF and/or UHF antennas or a single combination VHF/UHF antenna

INSTALLATION INSTRUCTIONS

Head Unit

VHF/UHF

Antenna

UHF

Antenna

Second TV

(if required)

To TV

(via “IN” connection

on power supply

)

1. Attach Head Unit to the mast

using cable tie supplied. (Fig 1)

2. Make connection to Head Unit

as shown (Fig 2).

Close cover after ensuring

cables are attached securely and

positioned correctly.

3. Attach the power supply to wall

or skirting board.

A ventilation gap of at least 25mm

should be left around the front and

sides of the unit.

4. Connect the downlead from

the head unit to the “IN” socket.

Connect the output lead from the

socket marked “TV” to the recieving

installation (satellite reciever, VCR,

TV etc). When all connections have

been made, plug power supply into

mains outlet and switch on - Yellow

light will illuminate.

Note: If light shows red colour

there is a short circuit on the “IN”

connection.

TIP: If installing ampliﬁer to old

antenna, ensure antenna is in good

condition and cable terminations

are secure.

Power supply

Wallplate

Fig 1 Fig 2

CPIN002337

AP700-BUN_CPIN002337.indd 1 29/03/12 10:17 AM

ANTSIG is proudly produced by Antsig Australia Pty. Ltd.

Visit us at: www.ANTSIG.com

Arlec Australia Pty. Ltd. ACN 009 322 105 (“Arlec”) gives the Warranty.

Arlec’s telephone number, address and email address are:

Customer Service: (03) 9982 5111

Building 3, 31 – 41 Joseph Street, Blackburn North, Victoria, 3130

Blackburn North LPO, P.O. Box 1065, Blackburn North, 3130

Email: [email protected]

CPIN002337

CONTENTS:

Package includes:

• F-Connector 0.9 metre ﬂy lead.

• 2 x F-Connector male to PAL female adaptor.

• 2 x twist on F-Connector male for RG6 cable.

• Cable tie.

• Masthead ampliﬁer unit.

• Power supply unit.

SAFETY INFORMATION

The Power Supply is designed for indoor use only.

The supply plug must remain readily accessilbe.

Unit is not disconnected from mains unless supply plug is removed.

Antsig guarantees this product in accordance with the Australian Consumer Law.

Antsig also warrants to the original ﬁrst purchaser of this product (“you”) from a retailer that this product will be

free of defects in materials and workmanship for a period of 12 months from the date of purchase; provided the

product is not used other than for the purpose, or in a manner not within the scope of the recommendations and

limitations, speciﬁed by Antsig, is new and not damaged at the time of purchase, has not been subjected to abuse,

misuse, neglect or damage, has not been modiﬁed or repaired without the approval of Antsig and has not been

used for commercial purposes (“Warranty”).

If you wish to claim on the Warranty, you must, at your own expense, return the product, and provide proof of

original purchase and your name, address and telephone number, to Antsig at the address below or the retailer

from whom you originally purchased the product within 12 months from the date of purchase.

Antsig will (or authorise the retailer to) assess any claim you may make on the Warranty in the above manner and

if, in Antsig’s reasonable opinion, the Warranty applies, Antsig will at its own option and expense (or authorise the

retailer to) replace the product with the same or similar product or repair the product and return it to you or refund

the price you paid for the product. Antsig will bear its own expenses of doing those things, and you must bear any

other expenses of claiming on the Warranty.

The Warranty is in addition to other rights and remedies you may have under a law in relation to the product to

which the Warranty relates.

Our goods come with guarantees that cannot be excluded under the Australian Consumer Law.

You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably

foreseeable loss or damage.

You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the

failure does not amount to a major failure.

subject to copyright and

must not be reproduced,

copied or otherwise used in

any way or for any purpose

without the consent in

writing of the owner

WARRANTY

AP700-BUN_CPIN002337.indd 2 29/03/12 10:17 AM

Antsig AP700 Installation guide

Brand: Antsig

Model: AP700

Type: Installation guide

Download PDF

report

Antsig AP700 Installation guide

Antsig AP700 Installation guide

Related papers

Other documents