Arlec ABL104 Installation guide

Brand: Arlec

Model: ABL104

Type: Installation guide

Arlec ABL104 is an up-and-down stainless steel wall light suitable for permanent use, both indoors and outdoors (weatherproof rating: IP44). It has a marine grade 316 stainless steel body and comes with a 12-month warranty. The light requires two GU10 halogen bulbs (not included), which can be easily replaced by unscrewing the front bezels of the lampholders. To clean the light, simply wipe it with a damp cloth and avoid using solvents or abrasive cleaners.

Arlec guarantees this product in accordance with the

Australian Consumer Law.

Arlec also warrants to the original rst purchaser of this

product (“you”) from a retailer that this product will be free

of defects in materials and workmanship for a period of

12 months from the date of purchase; provided the product is

not used other than for the purpose, or in a manner not within

the scope of the recommendations and limitations, specied

by Arlec, is new and not damaged at the time of purchase, has

not been subjected to abuse, misuse, neglect or damage, has

not been modied or repaired without the approval of Arlec and

has not been used for commercial purposes (“Warranty”).

If you wish to claim on the Warranty, you must, at your own

expense, return the product, and provide proof of original

purchase and your name, address and telephone number,

to Arlec at the address below or the retailer from whom you

originally purchased the product within 12 months from the

date of purchase.

Arlec will (or authorise the retailer to) assess any claim you

may make on the Warranty in the above manner and if, in

Arlec’s reasonable opinion, the Warranty applies, Arlec will

at its own option and expense (or authorise the retailer to)

replace the product with the same or similar product or repair

the product and return it to you or refund the price you paid

for the product. Arlec will bear its own expenses of doing those

things, and you must bear any other expenses of claiming on

the Warranty.

The Warranty is in addition to other rights and remedies you

may have under a law in relation to the product to which the

Warranty relates.

Our goods come with guarantees that cannot be excluded

under the Australian Consumer Law.

You are entitled to a replacement or refund for a major failure

and for compensation for any other reasonably foreseeable loss

or damage. You are also entitled to have the goods repaired

or replaced if the goods fail to be of acceptable quality and the

failure does not amount to a major failure.

WARRANTY

SPECIFICATIONS

Arlec Australia Pty. Ltd. ACN 009 322 105 (“Arlec”) gives the Warranty.

Arlec’s telephone number, address and email address are:

Customer Service: (03) 9982 5111

Building 3, 31 – 41 Joseph Street, Blackburn North, Victoria, 3130

Blackburn North LPO, P.O. Box 1065, Blackburn North, 3130

Email: [email protected]

CPIN002328

Maximum Globe : 35W GU10 Halogen Type

Weatherproof Rating : IP44

Stainless Steel : 316 Marine Grade

steel, then, use a sponge to rinse the nish

with clean water and wipe dry if necessary.

Follow polish lines.

Do not use solvents or abrasive cleaners

on any part of your light.

To clean the stubborn stains and

discolouration on all nishes, use mild

cleaning solutions as well as a rag, and a

sponge or bre brush (soft nylon or natural

bristle. You can also use an old toothbrush).

Then, rinse it well with clean water and

wipe dry. Follow polish lines.

Replace any cracked protective shield. In

the event of a cracked or broken front glass

lens, please remove the lantern or replace

the glass lens (Arlec Part Number SS2309

for the Top bezel and glass and SS2310

for the Bottom Bezel and glass) as soon

as possible.

ABL104

INSTALLATION INSTRUCTIONS

STAINLESS STEEL

UP/DOWN WALL LIGHT

Oberon

Important! please read these InstructIons carefully.

CPIN002328

MAINTENANCE (CONT)

INSTALLATION

INTRODUCTION

IDENTIFICATION

Place the mounting base over the position

for mounting and mark the screw holes.

Use the two mounting holes on the surface

of the mounting base and ensure the “UP”

marking points upward. Drill suitable holes,

and then feed the supply cable through

the rubber seal on the rear of the mounting

base. Before xing the mounting base in

place, seal any holes in the wall through

which the supply cable passes so as to

The ‘Oberon’ Stainless Steel Wall Light is

suitable for permanent use and must be

installed by a licensed electrician.

The lamp housing consists of a tubular,

marine grade stainless steel body, each side

in two parts – a bezel and support section.

The support sections are in turn xed to a

mounting base. Make sure that the UP side

bezel which has internal thread is attached

to the UP side support section which has

external thread, and the DOWN side bezel

which has external thread is attached to

the DOWN side support section which has

internal thread. (Refer Fig1)

weatherproof it. Secure mounting base

with supplied screws, again ensuring the

“UP” marking is pointed upwards.

(Refer Fig.2)

Mounting Holes

Drilled Holes

Mounting Base

Rubber Seal

DOWN

Fig. 02

WIRING

The terminal block wired to the rear of

the light must be wired to the switched

active, neutral and earth of the lighting

circuit to which it is being connected.

Connect in accordance with Fig.3.

ACTIVE BROWN

Internal

Connection

House

Wiring

GREEN/YELLOW

BLUE

GREEN/YELLOW

NEUTRAL

EARTH

Fig. 03

Double check all connections and ensure

all terminal block screws are tight. Press

the terminal block in position on the

plastic pins in mounting base and ensure

that the rubber seal is in place on the

front of the mounting base. Fit the base

cover over the mounting base, xing it in

place with the ‘o’ rings and dome nuts

provided.

SETTING UP

Fix the bulb by unscrewing the front

bezels of the lampholders and inserting

bulbs. (Bulb is GU10 type halogen bulb,

rated 250V 35W max.). The bulbs lock

in place with a 1/8 twists clockwise and

then ret the front bezels

This product is suitable for permanent

use. The globes shall not be directed at,

nor placed near any object within 0.5m

from the front of the lamp.

BULB REPLACEMENT

Use only bulbs of same type and rating.

(Bulbs are GU10 type halogen bulb,

rated 250V 35W max.). If the light

has been working, allow to cool before

handling to replace a bulb.

Remove bulb by unscrewing front bezel

and twisting bulb 1/8 turn anticlockwise.

It should then pull out from the lampholder.

MAINTENANCE

To avoid dust build up wipe lightly with

a damp cloth as required.

Clean the stainless steel at least 2 times

per year with a soft cloth and a neutral

detergent in order to avoid corrosion.

This amount should change to 4 times

per year in coastal and industrial areas.

Care should be taken when cleaning to

prevent scratching. A soft cloth or ne-

hair brush should be used together with

a non-abrasive cleaner.

Use soap or mild detergents and water

(preferably warm water) in order to clean

the nish on the surface of the stainless

Fig. 01

Lens Bezel

Clear Glass Lens

Bulb

(NOT SUPPLIED)

Silicone ‘O’ Ring

Bulb

(NOT SUPPLIED)

Silicone ‘O’ Ring

Lampholder

Dome Nut

(for securing to

Mounting Base)

Small ‘O’ Ring

Rubber

Seal

Mounting Base

Mounting

Base Cover

Mounting Threads

Terminals on inside rear of fitting

DOWN

ACTIVE BROWN

Internal

Connection

House

Wiring

GREEN/YELLOW

BLUE

GREEN/YELLOW

NEUTRAL

EARTH

ARLEC ‘OBERON’ Stainless Steel Up/Down Wall Light ARLEC ‘OBERON’ Stainless Steel Up/Down Wall Light

Arlec ABL104 Installation guide

Arlec ABL104 Installation guide

Arlec ABL104 Installation guide

Related papers

Other documents