Kohler M MODULAR Installation Instructions Manual

Brand: Kohler

Model: M MODULAR

Type: Installation Instructions Manual

-1-

INSTALLATION INSTRUCTIONS

()

MIRRORED CABINET W/DEFOGGER

K-15512T

M MODULAR

, 2011

13-1 528437

BEFORE YOU BEGINBEFORE YOU BEGIN

Please read these instructions carefully to familiarize

yourself with the required tools, materials, and installation

sequences. Follow the sections that pertain to your

particular installation . This will help you avoid costly

mistakes. In addition to proper installation, read all

operating and safety instructions.

All information in these instructions is based upon the

latest product information available at the time of

publication. Kohler China. reserves the right to make

changes in product characteristics, packaging, or

availability at any time without notice.

These instructions contain important care, cleaning, and

warranty information-

Before installation carefully inspect the new fixture for any

signs of damage.

Tempered glass cannot be cut.

Don't use acidic or alkalic cleaners or

alcohol to clean the wooden surface. Use a dampened

cloth to clean.

please leave instructions for the

consumer.

WARNING: Risk of injury or product damage.

WARNING:

PARTS

Parts supplied with your cabinet. (For cabinet body and door

replacement, call customer service with model number.) Be

sure to check the cardboard supports in the carton, glass

parts are packed in them.

ACCESSORIES LISTACCESSORIES LIST

Screws ST3.5 35

ST3.5 35

Screws ST4.2 12

ST4.2 12

Connector Block

Hinge Clips

Glass

2 Level Box

Tissue Box

Wall Anchors

Snap-in Pins

X12

Caps of Screw

X10

Hole Plugs

X40

Top Clips

Mounting Bar

Glass Shelves

1179057-T01-A

-2-

489

116

762

682

406

735

ROUGHING-IN

UNIT : mm

PRE-DRILLED HOLEPRE-DRILLED HOLE

Pre-Drilled Hole for Side Kits

Pre-Drilled Hole for Cabinet-to-Cabinet

Pre-Drilled Hole for Recessed Cabinet

1179057-T01-A

-3-

INSTALLATION

NOTE

The cabinet has two ways of installation:

Recessing mounting.

Surface mounting.

Refer to the following instruction for mirror installation.

STEP

RECESSING THE MIRRORED CABINET INTO THE WALL

The Vertical installation changes the width of the roughout. Please refer to the picture below.

On installations of larger cabinet in combinations of 3 or more, the

center door, when open, may cause the cabinet to bow from the wall.

If this happens, drill a hole at the location shown in Figure J and

install a ST3.5X35 SCREW.

ST3.5X35

472mm for Width

472mm

Screws ST3.5 35

ST3.5 35

745mm high

745mm

Fig. 1 1

Figure J

3/4"

(19.1mm)

3/4"

(19.1mm)

Drill a hole through

Top of middle cabinet 3/4" (19.1 mm) from back

19.1mm

1179057-T01-A

-4-

STEP

Install screws through holes in mirrored cabinet as shown in Fig.1, 2

DO NOT OVER- TIGHTEN!

Use s .

Note:

crews ST3.5 35

ST3.5 35

Fig. 2 2

Top View

Stud and wall surface

Install dome caps over screws

Mirrored cabinet flange fits flush against wall

SURFACE MOUNTING THE MIRRORED CABINET ON A WALL

NOTE:

Install the side kits while surface mounting the mirrored

cabinet on the wall, additional order of the side kits.

Fig. 3 3

STEP

As shown in Fig 3, drill two 2- 5mm holes

in bottom mounting bar at indent location,

then drill 4- 6mm holes in wall at locations

shown in Fig 3, insert wall anchors.

Screws ST3.5 35 & Wall anchor

ST3.5 35

The highest point of table

Drill holes

4- 6mm

Fix the mounting bar to the

wall, level the mounting bar.

Drill holes

4- 6mm

750

320

1179057-T01-A

COMBINATION INSTALLATION OF SEVERAL MIRRORED CABINETS

-5-

1051705-T01-A

STEP

Fig. 5 5

Connect the cabinets by fixing the connector blocks to the side of the mirrored cabinet with ST4.2x12 screws.

ST4.2x12

For surface mounting installation, please fix the side kits bracket at the two sides of the combined cabinets with M4 screws.

STEP

Fig. 4 4

Top clips slide into this screw

channel from center opening.

Top of cabinet frame member

2 Top clips

WALL

Sit the mirrored cabinet on the mounting bar, then lower and tighten the

screws into place, as shown in Fig.4.

Screws ST3.5 35 & Wall anchor

ST3.5 35

Side Kits

Mirrored Cabinet Mirrored Cabinet

Connector Blocks

Mirrored Cabinet

Top clip for

surface mount

2 per cabinet

1179057-T01-A

Fig. 6B 6B

Assemble

Removal

Depth Adjustment

Height Adjustment

Side Adjustment

Fig. 6A 6A

AssembleAssemble

Removal

-6-

STEP

Door adjustments

If no light kit is installed, the hinge clips are not necessary

and the door can be allowed to swing 170 . If the door

hinges come with a 110 black plastic hinge clips are

required, snap the hinge clip over the elbow of the hinge

into the holes located on the hinge.

170

110

Remove the hinge cover or the blumotion before adjustion, see Fig 6A.

Adjust the hinge of door in 3 directions to make sure the door level as shown in Fig.6B.

Fig. 7 7

1179057-T01-A

STEP

Push/twist the pins into place & Fill the remaining holes with the plugs

Push one side of the shelf into the left or right clips.

Snap the shelf down into the opposite side. If the shelf is too tight, repeat the process from the other side.

Fig. 9 9

Fig. 8 8

Fig. 10 10

Put the tissue box, 2 level box and the glass into the cabinet as shown in Fig.8.

-7-

1179057-T01-A

-8-

STEP

Fig. 11 11

The step is only for the installation of defogger. See Fig 11,

external power supply.

(220V/50HZ)

220V/50HZ

5. .

6. .

USER MAINTENANCEUSER MAINTENANCE

Warn! Risk of product damage.

5. The mirrored cabinet door and interior are constructed of

mirror and aluminum. Use only a damp cloth to clean.

Spray the cloth, not the mirror when cleaning. Mirrors are

damaged by the use of ammonia or vinegar based

cleaners. Rubbing alcohol can be used for stubborn stains

6. Use no abrasive cleansers on any part of the mirrored

cabinet.

7. The white frame should be cleaned with a damp cloth only.

Many cleansers contain abrasive and chemical substance

which is not suitable for cleaning stainless steel, enamel,

plating or plastic products. You may use mild cleansers or

soaps to clean the surfaces. Wipe any splashes of cleaner

solutions from the surface with clean soft cloth.

Maintain ventilation in the bathroom, and separate the dry

area from the damp one if conditions permit. Try to open

the door and windows of the bathroom and maintain good

ventilation.

Kohler mirrored cabinet are dealt with strict procedures for

damp-proof, whose good damp-proof function ensures

good performance even in bathroom of huge humidity. Yet

do not splash and pour water directly on the mirrored

cabinet. Make sure that the bathroom is not over damp

and wipe any splashes from surfaces immediately.

Maintenance of door board: Clean and wipe door board

regularly, and wipe the condensation vapor with dry and

soft cloth.

1179057-T01-A

Kohler M MODULAR Installation Instructions Manual

Kohler M MODULAR Installation Instructions Manual

Kohler M MODULAR Installation Instructions Manual

Related papers

Other documents