Style Selections 8408 Installation guide

Brand
Style Selections
Model
8408
Type
Installation guide

Style Selections 8408 is a 24" x 36" oval mirror with a beveled edge. It comes with a 12" wall mounting clip, 3 plastic wall anchors, 3 screws, and a disposable level.

The mirror is easy to install and can be mounted in just a few steps. First, you need to determine the location where you want to install the mirror and mark the spot on the wall. Then, you need to drill three holes for the wall anchors and screw the mounting clip into place. Finally, you need to carefully place the mirror onto the mounting clip.

Style Selections 8408 is a 24" x 36" oval mirror with a beveled edge. It comes with a 12" wall mounting clip, 3 plastic wall anchors, 3 screws, and a disposable level.

The mirror is easy to install and can be mounted in just a few steps. First, you need to determine the location where you want to install the mirror and mark the spot on the wall. Then, you need to drill three holes for the wall anchors and screw the mounting clip into place. Finally, you need to carefully place the mirror onto the mounting clip.

WARNING: Always wear safety goggles and gloves when
handling glass. Handle mirror carefully. Do not bump mirror
against hard surfaces. Place on towel or soft surface such
as carpet when handling. READ INSTRUCTIONS CAREFULLY
BEFORE STARTING.
#2 Place the mirror on the wall in area chosen.
(Two people are needed for this task).
Position the mirror at the desired height in
the center of the location. With Pencil mark
a dot or line on the very top edge of the arch.
See (Fig.1) Set mirror aside In safe place.
#4 From this spot, position the 12” Hanging Clip.
The top of the hanging clip should be centered
on the spot marked on the wall 6" from the top
of the mirror. Mark the locations for the screw
holes at the bottom of the clip, using the level
to make sure the clip is level and straight.
(Fig.3) Set the clip and level aside.
#5 Using the Drill and 3/16” Drill Bit-Pre Drill the
holes for the wall anchors. Lightly tap the
plastic wall anchors into place with hammer.
#6 Reposition the 12” Clip and secure to the wall
with the screws provided. Check the level
again to determine that the clip is straight
and level. (Fig.4)
#3 From the dot made on the wall, using a
tape rule, measure down 6" and mark
the spot on the wall (Fig.2)
#1 Using a tape measure, check the location where the mirror is to be installed. Be sure the mirror will fit in the desired
location. Approximately 24”W x 36”H is needed for the mirror to fit.
Parts List:
• 24” x 36” Oval Mirror with Mounting Bracket
• 12” Wall Mounting Clip
• 3 Plastic Wall Anchors
• 3 Screws
• 1 Disposable Level
Tools Needed:
Pencil and Eraser, Drill and 3/16” Drill Bit,
Screw Gun or Driver with Phillips Head,
Tape Measure, Hammer and Friend to help.
(Two People are required to mount this mirror).
MOUNTING INSTRUCTIONS FOR MIRRORS
Model #8408 24" x 36" BEVELED OVAL MIRROR
Fig.1
Fig.3
Fig.4
#7 Carefully place the mirror with the mounting
plate onto the installed wall clip. Mirror can
be adjusted side to side by gently sliding the
mirror along the clip.
With mirror centered installation is complete - you look marvelous.
6"
Fig.2
Disposable
Level
  • Page 1 1

Style Selections 8408 Installation guide

Brand
Style Selections
Model
8408
Type
Installation guide

Style Selections 8408 is a 24" x 36" oval mirror with a beveled edge. It comes with a 12" wall mounting clip, 3 plastic wall anchors, 3 screws, and a disposable level.

The mirror is easy to install and can be mounted in just a few steps. First, you need to determine the location where you want to install the mirror and mark the spot on the wall. Then, you need to drill three holes for the wall anchors and screw the mounting clip into place. Finally, you need to carefully place the mirror onto the mounting clip.

Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Other documents