Lincoln Manufacturing 808N Operating instructions

Brand: Lincoln Manufacturing

Model: 808N

Type: Operating instructions

This manual is also suitable for

606N

Lincoln Manufacturing 808N This device is intended for use by trained and experienced operators only, and all operators must read the provided Operation Manual before using the equipment.

The Lincoln Manufacturing 808N is a heavy-duty machine capable of wedging a variety of fruits and vegetables. The 808N is particularly well-suited for wedging lemons, limes, and tomatoes. The machine features a durable aluminum base and a stainless steel blade assembly. The blade assembly is easily removable for cleaning and replacement.

The 808N is simple to use.

Lincoln Manufacturing 808N This device is intended for use by trained and experienced operators only, and all operators must read the provided Operation Manual before using the equipment.

The 808N is simple to use.

INSTALLATION & OPERATING

INSTRUCTIONS

for

REDCO

WEDGEMASTER™ MODELS 606N & 808N

COREMASTER™ - REDI WEDGE™ - GREAT WEDGER™

WedgemasterOps P/N: 2802379 REV: 4/10/07

Wedgemsater Ops Manual

WARNING AND SAFETY INFORMATION

LIMITED 2 YEAR WARRANTY

Lincoln Foodservice Products, LLC (“Lincoln”) warrants, to the original purchaser for use in the United States of

America, that each new item of Redco food preparation utensils (other than blades) manufactured by it (“Warranted

Product”) is free of defects in material and workmanship under normal use and conditions.

The exclusive remedy available under this Limited Warranty is that Lincoln will, free of charge, but at its option,

subject to, and in accordance with the terms and conditions of the Limited Warranty, repair or replace, for the

original purchaser for use in the United States of America, any Warranted Products or part thereof that proves to be

defective with the same or a similar item or part, if it is returned to Lincoln in accordance with the procedure set out

on the warranty card.

This limited Warranty applies only to the original parts of Warranted Products sold for use in the United States of

America and does not apply to any Warranted Products located outside the United States of America, regardless of

where sold, or to any item or part thereof that has been subjected to accident, casualty, alteration, misuse, or abuse

or if the date of manufacture is altered or removed.

THIS LIMITED WARRANTY DOES NOT APPLY TO BLADES WHICH ARE SOLD COMPLETELY WITHOUT

WARRANTY OR GUARANTEE OF ANY KIND, EXPRESSED OR IMPLIED. THE OBLIGATION OF LINCOLN IS

LIMITED TO THE ABOVE AND, EXCEPT AS EXPRESSLY STATED HEREIN, LINCOLN MAKES NO

GUARANTEES OR WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, WITHOUT LIMITATION,

WARRANTIES OF FITNESS OR MERCHANTABILITY, WITH RESPECT TO WARRANTED PRODUCTS.

LINCOLN SHALL NOT BE LIABLE FOR SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES OF ANY

KIND. NO ONE IS AUTHORIZED TO MAKE ANY GUARANTEES OR WARRANTIES, EXPRESSED OR

IMPLIED, ON BEHALF OF LINCOLN.

SOME STATES DO NOT ALLOW LIMITATIONS OF IMPLIED WARRANTIES, OR THE EXCLUSION OR

LIMITATION OF INCIDENTAL OR CONSEQUENTIALY DAMAGES IN CONNECTION WITH THE SALE OF

CONSUMER PRODUCTS, CONSEQUENTIALY, IF YOU ARE A CONSUMER, AS THAT TERM IS LEGALLY

DEFINED, THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU.

TABLE OF CONTENTS

Operating Instructions………………………………………………………………………………………………………….. 3

Cleaning…...…………………………………………………………………………………………………………………..… 3

Blade Servicing & Replacement……………………………………………………………………………………………… 4

Parts List...………………………………...……………………………….………………………………………………….… 6

Exploded View Drawing…………………………...……..………………………..………………………………………...… 7

WARNING

THIS MACHINE CONTAINS SHARP BLADES AND CAN CAUSE SERIOUS INJURY OR DEATH IF NOT

HANDLED PROPERLY. ALL OPERATORS OF THIS EQUIPMENT SHOULD READ THIS OPERATION

MANUAL BEFORE OPERATING EQUIPMENT.

IN ORDER TO AVOID DAMAGE TO PEOPLE AND THE APPLIANCE, READ AND FOLLOW THE

MANUFACTURER’S INSTRUCTIONS FOR THE CLEANING OF THIS EQUIPMENT.

Wedgemaster Ops Manual

Blades are sharp and can cause injury. Check machine before using. Be sure machine is clean. Check for

broken, nicked or dull blades and if found, replace blade assembly. Check to be sure Pusher Head Assembly can

move freely. Lubricate if necessary using a light coating of mineral oil, Petrol Gel or food grade lubricant. DO NOT

LUBRICATE WITH COOKING OIL AS IT WILL BECOME STICKY.

OPERATION INSTRUCTIONS

1. Place machine on a level counter or table.

2. When wedging lemons or limes, it is best to cut off both ends of the fruit before wedging.

3. When wedging tomatoes, use a Tomato King Scooper to remove the stem scar.

4. Raise the head of the Wedgemaster with one hand. Center the product that you are going to cut on the

center spike, which is the middle of the blade assembly.

5. Remove your hand away from the blade assembly. With a strong, quick, downward thrust of the head

assembly with one hand (while holding unit leg with other hand), force the product through the blade to

make perfect wedges.

6. Clean and lubricate your machine immediately.

CLEANING INSTRUCTIONS

1. After use, remove the head and dunk base into hot soapy water. Rinse with hot water and let air dry. DO

NOT wipe the blades.

2. Wash the pusher head in the same fashion.

3. Let machine air dry.

CAUTION

FOOD ACIDS WILL MAKE BLADES DULL AND CORRODE THE METAL.

ALWAYS CLEAN THIS FOOD PREPARATION MACHINE IMMEDIATELY

AFTER EVERY USE!

DANGER:

THIS MACHINE CONTAINS SHARP BLADES AND CAN CAUSE SERIOUS

INJURY OR DEATH IF NOT HANDLED PROPERLY. ALL OPERATORS OF

THIS EQUIPMENT SHOULD READ THIS OPERATION MANUAL BEFORE

OPERATING EQUIPMENT.

CAUTION:

BLADES ARE SHARP AND CAN CAUSE INJURY. NEVER USE MACHINE UNLESS

ALL RUBBER FEET ARE IN PLACE.

CAUTION

PRIOR TO USING YOUR NEW EQUIPMENT, IT IS IMPORTANT TO CLEAN

THE UNIT. WASH NEW BLADES WITH WARM SOAPY WATER AND RINSE

THOROUGHLY TO REMOVE THIN PROTECTIVE OIL FILM. LET AIR DRY.

CAUTION

CAUTION:

PRIOR TO USING YOUR NEW EQUIPMENT, IT IS IMPORTANT TO CLEAN THE

UNIT. WASH NEW BLADES WITH WARM SOAPY WATER AND RINSE

THOROUGHLY TO REMOVE THIN PROTECTIVE OIL FILM. LET AIR DRY.

Wedgemsater Ops Manual

BLADE SERVICING AND REPLACEMENT

If the machine no longer slices cleanly or without damage, the blades could be dull and need to be replaced.

Broken, bent, nicked, or dull blades must be replaced immediately. Change the complete assembly.

1. Allow yourself ample room to work on a flat, dry surface.

2. Turn machine on its side and remove the Pusher Head Assembly.

3. Remove the two (2) Blade Screws from the bottom of the Base Assembly. Carefully remove the blade

assembly by gently pushing up from underneath the Base Assembly. This will remove the blade assembly

from the unit.

4. Install new blade assembly by carefully placing it inside the top of the Base Assembly. NEVER push down

on blade assembly when inserting into the base! Once in place, insert the two (2) blade screws until tight.

DISPOSE OF USED BLADE ASSEMBLIES!

DANGER:

HANDLE WITH EXTREME CARE AS BLADES ARE SHARP AND CAN CAUSE

INJURY OR DEATH IF NOT HANDLED PROPERLY. ALL OPERATORS OF

THIS EQUIPMENT SHOULD READ THIS OPERATION MANUAL BEFORE

OPERATING EQUIPMENT.

CAUTION

PRIOR TO USING YOUR NEW EQUIPMENT, IT IS IMPORTANT TO CLEAN

THE UNIT. WASH NEW BLADES WITH WARM SOAPY WATER AND RINSE

THOROUGHLY TO REMOVE THE THIN PROTECTIVE OIL FILM.

Wedgemaster Ops Manual

This page intentionally left blank.

Wedgemsater Ops Manual

SPARE PARTS – WEDGEMASTER / COREMASTER

LETTER

PART

NUMBER

DESCRIPTION

A 0304 Red Knob Handle

B 2321 Aluminum Nipple

C 301 Base Housing & Rod Assembly

D 302 Blade Screw

E 303 Rubber Foot

F 305 “O” Ring

316 Head Assembly, W.M. 6-Section

318 Head Assembly, W.M. 8-Section

315 Head Assembly, W.M. 10-Section

324 Head Assembly, W.M. 12-Section

326 Head Assembly, C.M. 6-Section

328 Head Assembly, C.M. 8-Section

304 Blade Assembly, W.M. 4-Section

306 Blade Assembly, W.M. 6-Section

308 Blade Assembly, W.M. 8-Section

310 Blade Assembly, W.M. 10-Section

312 Blade Assembly, W.M. 12-Section

304K Blade Assembly, W.M. K.K. 4-Section

306K Blade Assembly, W.M. K.K. 6-Section

308K Blade Assembly, W.M. K.K. 8-Section

336 Blade Assembly, C.M. 6-Section

338 Blade Assembly, C.M. 8-Section

Wedgemaster Ops Manual

EXPLODED VIEW – WEDGEMASTER / COREMASTER

Wedgemsater Ops Manual

SPARE PARTS – REDI WEDGE

LETTER

PART

NUMBER

DESCRIPTION

A 0304 Red Handle Knob

316 RW Head Assembly, 6-section

318 RW Head Assembly, 8-section

315 RW Head Assembly, 10-section

312 RW Head Assembly, 12-section

C 4320R Wall Bracket

D 9321 Puller Handle

E 2316 Guide Rod & Blade Ring Assembly

F 9322 Link

G 9324 Adapter

H 2321 Alum. Nipple for Knob

I 305 “O” Ring

J 302 Blade Screw

K 352 5/16-18 x 1-1/2” HHMS

L 353 5/16-18 Lock Nut

M 354 5/16 Internal Star Washer

N 355 5/16-18 Wing Nut

O 356 ¼-20 Wing Nut

P 357 5/16-18 x 1 HHMS

304 Blade Assembly, 4-section

306 Blade Assembly, 6-section

308 Blade Assembly, 8-section

310 Blade Assembly, 10-section

312 Blade Assembly, 12-section

Wedgemaster Ops Manual

EXPLODED VIEW – REDI WEDGE

Wedgemsater Ops Manual

SPARE PARTS – GREAT WEDGER

LETTER

PART

NUMBER

DESCRIPTION

A 0304 Red Handle Knob

316 Head, 6-section

318 Head, 8-section

C 305 “O” Ring

D 2319 Black Rubber Bumbers

E 2321 Alum. Nipple for Knob

2306 Blade Assembly, 6-section

2308 Blade Assembly, 8-section

Wedgemaster Ops Manual

EXPLODED VIEW – GREAT WEDGER

Wedgemsater Ops Manual

Lincoln Foodservice Product, LLC

1111 North Hadley Road

Fort Wayne, Indiana 46804

United States of America

Telephone: (260) 459-8200

U.S. Fax: (888) 790-8193

Int’l Fax: (260) 436-0735

Technical Support Hotline: (800) 678-9511

www.lincolnsmallwares.com

Lincoln Manufacturing 808N Operating instructions

Brand: Lincoln Manufacturing

Model: 808N

Type: Operating instructions

This manual is also suitable for

606N

Lincoln Manufacturing 808N This device is intended for use by trained and experienced operators only, and all operators must read the provided Operation Manual before using the equipment.

The 808N is simple to use.

Download PDF

report