Lincoln Manufacturing 606N Operating instructions

Brand
Lincoln Manufacturing
Model
606N
Type
Operating instructions

This manual is also suitable for

INSTALLATION & OPERATING
INSTRUCTIONS
for
REDCO
®
WEDGEMASTER™ MODELS 606N & 808N
COREMASTER™ - REDI WEDGE™ - GREAT WEDGER™
WedgemasterOps P/N: 2802379 REV: 4/10/07
Wedgemsater Ops Manual
2
WARNING AND SAFETY INFORMATION
LIMITED 2 YEAR WARRANTY
Lincoln Foodservice Products, LLC (“Lincoln”) warrants, to the original purchaser for use in the United States of
America, that each new item of Redco food preparation utensils (other than blades) manufactured by it (“Warranted
Product”) is free of defects in material and workmanship under normal use and conditions.
The exclusive remedy available under this Limited Warranty is that Lincoln will, free of charge, but at its option,
subject to, and in accordance with the terms and conditions of the Limited Warranty, repair or replace, for the
original purchaser for use in the United States of America, any Warranted Products or part thereof that proves to be
defective with the same or a similar item or part, if it is returned to Lincoln in accordance with the procedure set out
on the warranty card.
This limited Warranty applies only to the original parts of Warranted Products sold for use in the United States of
America and does not apply to any Warranted Products located outside the United States of America, regardless of
where sold, or to any item or part thereof that has been subjected to accident, casualty, alteration, misuse, or abuse
or if the date of manufacture is altered or removed.
THIS LIMITED WARRANTY DOES NOT APPLY TO BLADES WHICH ARE SOLD COMPLETELY WITHOUT
WARRANTY OR GUARANTEE OF ANY KIND, EXPRESSED OR IMPLIED. THE OBLIGATION OF LINCOLN IS
LIMITED TO THE ABOVE AND, EXCEPT AS EXPRESSLY STATED HEREIN, LINCOLN MAKES NO
GUARANTEES OR WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, WITHOUT LIMITATION,
WARRANTIES OF FITNESS OR MERCHANTABILITY, WITH RESPECT TO WARRANTED PRODUCTS.
LINCOLN SHALL NOT BE LIABLE FOR SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES OF ANY
KIND. NO ONE IS AUTHORIZED TO MAKE ANY GUARANTEES OR WARRANTIES, EXPRESSED OR
IMPLIED, ON BEHALF OF LINCOLN.
SOME STATES DO NOT ALLOW LIMITATIONS OF IMPLIED WARRANTIES, OR THE EXCLUSION OR
LIMITATION OF INCIDENTAL OR CONSEQUENTIALY DAMAGES IN CONNECTION WITH THE SALE OF
CONSUMER PRODUCTS, CONSEQUENTIALY, IF YOU ARE A CONSUMER, AS THAT TERM IS LEGALLY
DEFINED, THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU.
TABLE OF CONTENTS
Operating Instructions………………………………………………………………………………………………………….. 3
Cleaning…...…………………………………………………………………………………………………………………..… 3
Blade Servicing & Replacement……………………………………………………………………………………………… 4
Parts List...………………………………...……………………………….………………………………………………….… 6
Exploded View Drawing…………………………...……..………………………..………………………………………...… 7
!
WARNING
!
THIS MACHINE CONTAINS SHARP BLADES AND CAN CAUSE SERIOUS INJURY OR DEATH IF NOT
HANDLED PROPERLY. ALL OPERATORS OF THIS EQUIPMENT SHOULD READ THIS OPERATION
MANUAL BEFORE OPERATING EQUIPMENT.
IN ORDER TO AVOID DAMAGE TO PEOPLE AND THE APPLIANCE, READ AND FOLLOW THE
MANUFACTURER’S INSTRUCTIONS FOR THE CLEANING OF THIS EQUIPMENT.
Wedgemaster Ops Manual
3
Blades are sharp and can cause injury. Check machine before using. Be sure machine is clean. Check for
broken, nicked or dull blades and if found, replace blade assembly. Check to be sure Pusher Head Assembly can
move freely. Lubricate if necessary using a light coating of mineral oil, Petrol Gel or food grade lubricant. DO NOT
LUBRICATE WITH COOKING OIL AS IT WILL BECOME STICKY.
OPERATION INSTRUCTIONS
1. Place machine on a level counter or table.
2. When wedging lemons or limes, it is best to cut off both ends of the fruit before wedging.
3. When wedging tomatoes, use a Tomato King Scooper to remove the stem scar.
4. Raise the head of the Wedgemaster with one hand. Center the product that you are going to cut on the
center spike, which is the middle of the blade assembly.
5. Remove your hand away from the blade assembly. With a strong, quick, downward thrust of the head
assembly with one hand (while holding unit leg with other hand), force the product through the blade to
make perfect wedges.
6. Clean and lubricate your machine immediately.
CLEANING INSTRUCTIONS
1. After use, remove the head and dunk base into hot soapy water. Rinse with hot water and let air dry. DO
NOT wipe the blades.
2. Wash the pusher head in the same fashion.
3. Let machine air dry.
!
CAUTION
:
FOOD ACIDS WILL MAKE BLADES DULL AND CORRODE THE METAL.
ALWAYS CLEAN THIS FOOD PREPARATION MACHINE IMMEDIATELY
AFTER EVERY USE!
!
DANGER:
THIS MACHINE CONTAINS SHARP BLADES AND CAN CAUSE SERIOUS
INJURY OR DEATH IF NOT HANDLED PROPERLY. ALL OPERATORS OF
THIS EQUIPMENT SHOULD READ THIS OPERATION MANUAL BEFORE
OPERATING EQUIPMENT.
!
CAUTION:
BLADES ARE SHARP AND CAN CAUSE INJURY. NEVER USE MACHINE UNLESS
ALL RUBBER FEET ARE IN PLACE.
!
CAUTION
:
PRIOR TO USING YOUR NEW EQUIPMENT, IT IS IMPORTANT TO CLEAN
THE UNIT. WASH NEW BLADES WITH WARM SOAPY WATER AND RINSE
THOROUGHLY TO REMOVE THIN PROTECTIVE OIL FILM. LET AIR DRY.
!
CAUTION
!
CAUTION:
PRIOR TO USING YOUR NEW EQUIPMENT, IT IS IMPORTANT TO CLEAN THE
UNIT. WASH NEW BLADES WITH WARM SOAPY WATER AND RINSE
THOROUGHLY TO REMOVE THIN PROTECTIVE OIL FILM. LET AIR DRY.
Wedgemsater Ops Manual
4
BLADE SERVICING AND REPLACEMENT
If the machine no longer slices cleanly or without damage, the blades could be dull and need to be replaced.
Broken, bent, nicked, or dull blades must be replaced immediately. Change the complete assembly.
1. Allow yourself ample room to work on a flat, dry surface.
2. Turn machine on its side and remove the Pusher Head Assembly.
3. Remove the two (2) Blade Screws from the bottom of the Base Assembly. Carefully remove the blade
assembly by gently pushing up from underneath the Base Assembly. This will remove the blade assembly
from the unit.
4. Install new blade assembly by carefully placing it inside the top of the Base Assembly. NEVER push down
on blade assembly when inserting into the base! Once in place, insert the two (2) blade screws until tight.
DISPOSE OF USED BLADE ASSEMBLIES!
!
DANGER:
HANDLE WITH EXTREME CARE AS BLADES ARE SHARP AND CAN CAUSE
INJURY OR DEATH IF NOT HANDLED PROPERLY. ALL OPERATORS OF
THIS EQUIPMENT SHOULD READ THIS OPERATION MANUAL BEFORE
OPERATING EQUIPMENT.
!
CAUTION
:
PRIOR TO USING YOUR NEW EQUIPMENT, IT IS IMPORTANT TO CLEAN
THE UNIT. WASH NEW BLADES WITH WARM SOAPY WATER AND RINSE
THOROUGHLY TO REMOVE THE THIN PROTECTIVE OIL FILM.
Wedgemaster Ops Manual
5
This page intentionally left blank.
Wedgemsater Ops Manual
6
SPARE PARTS – WEDGEMASTER / COREMASTER
LETTER
PART
NUMBER
DESCRIPTION
A 0304 Red Knob Handle
B 2321 Aluminum Nipple
C 301 Base Housing & Rod Assembly
D 302 Blade Screw
E 303 Rubber Foot
F 305 “O” Ring
316 Head Assembly, W.M. 6-Section
318 Head Assembly, W.M. 8-Section
315 Head Assembly, W.M. 10-Section
324 Head Assembly, W.M. 12-Section
326 Head Assembly, C.M. 6-Section
G
328 Head Assembly, C.M. 8-Section
304 Blade Assembly, W.M. 4-Section
306 Blade Assembly, W.M. 6-Section
308 Blade Assembly, W.M. 8-Section
310 Blade Assembly, W.M. 10-Section
312 Blade Assembly, W.M. 12-Section
304K Blade Assembly, W.M. K.K. 4-Section
306K Blade Assembly, W.M. K.K. 6-Section
308K Blade Assembly, W.M. K.K. 8-Section
336 Blade Assembly, C.M. 6-Section
H
338 Blade Assembly, C.M. 8-Section
Wedgemaster Ops Manual
7
EXPLODED VIEW – WEDGEMASTER / COREMASTER
Wedgemsater Ops Manual
8
SPARE PARTS – REDI WEDGE
LETTER
PART
NUMBER
DESCRIPTION
A 0304 Red Handle Knob
316 RW Head Assembly, 6-section
318 RW Head Assembly, 8-section
315 RW Head Assembly, 10-section
B
312 RW Head Assembly, 12-section
C 4320R Wall Bracket
D 9321 Puller Handle
E 2316 Guide Rod & Blade Ring Assembly
F 9322 Link
G 9324 Adapter
H 2321 Alum. Nipple for Knob
I 305 “O” Ring
J 302 Blade Screw
K 352 5/16-18 x 1-1/2” HHMS
L 353 5/16-18 Lock Nut
M 354 5/16 Internal Star Washer
N 355 5/16-18 Wing Nut
O 356 ¼-20 Wing Nut
P 357 5/16-18 x 1 HHMS
304 Blade Assembly, 4-section
306 Blade Assembly, 6-section
308 Blade Assembly, 8-section
310 Blade Assembly, 10-section
Q
312 Blade Assembly, 12-section
Wedgemaster Ops Manual
9
EXPLODED VIEW – REDI WEDGE
Wedgemsater Ops Manual
10
SPARE PARTS – GREAT WEDGER
LETTER
PART
NUMBER
DESCRIPTION
A 0304 Red Handle Knob
316 Head, 6-section
B
318 Head, 8-section
C 305 “O” Ring
D 2319 Black Rubber Bumbers
E 2321 Alum. Nipple for Knob
2306 Blade Assembly, 6-section
F
2308 Blade Assembly, 8-section
Wedgemaster Ops Manual
11
EXPLODED VIEW – GREAT WEDGER
Wedgemsater Ops Manual
12
Lincoln Foodservice Product, LLC
1111 North Hadley Road
Fort Wayne, Indiana 46804
United States of America
Telephone: (260) 459-8200
U.S. Fax: (888) 790-8193
Int’l Fax: (260) 436-0735
Technical Support Hotline: (800) 678-9511
www.lincolnsmallwares.com
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12

Lincoln Manufacturing 606N Operating instructions

Brand
Lincoln Manufacturing
Model
606N
Type
Operating instructions
This manual is also suitable for
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents