ALIBI ALI-BC700G Quick Installation Manual

ALIBI
Brand
ALIBI
Model
ALI-BC700G
Category
Security cameras
Type
Quick Installation Manual
1
www.observint.com
ALI-BC700_CQ
7/7/14
What’s in the box
• Camera assembly
• Mounting hardware
• This instruction guide
• Drill template
ALIL-BC700G (left) and ALI-BC700VFG drill templates
Tools you need
To install the camera, you will need:
• 12 Vdc power source. See Specications for wattage requirement.
• Tools and additional fasteners (may be required) for mounting the camera
• Phillips screwdriver
• Video and power extension cable
• CCTV video setup monitor (optional)
Installation
Before installation:
• Make sure that the device is in good condition and all the assembly parts are included.
• Check the specication of the products for the installation environment.
• Make sure that the wall or the ceiling is strong enough to withstand 3 times the weight of the camera.
• To avoid re or shock hazard, use only UL listed power supplies. Verify that the power supply will
provide the rated voltage and wattage for the camera. See the Specications section.
During installation:
• Camera Lens: Handle the camera carefully to prevent scratching or soiling the lens. If the lens or IR
array shield becomes soiled, clean it only with approved products. See the
Cleaning section.
• Monitor impedance: Set the monitor impedance switch to 75 Ω.
• Power supply: Camera drop cable: The camera drop cable includes two connectors:
— Video BNC connector: For transmission of the video signal across a coax (75 Ω) extension cable.
— Power connector: When applying Vdc power, observe the power polarity. See the picture below
for the connector polarity conguration.
Mounting the camera
An ALI-BC700 series camera can be mounted on a wall or ceiling that has sucient strength to support it.
The video/power drop cable from the camera can be routed either through mounting surface or through a
cable guide on the edge of the mounting base.
ALI-BC700G camera typical ceiling mounting
ALI-BC700 Series Infrared Bullet
Cameras Quick Installation Guide
ForProducts: ALI-BC700G, ALI-BC700VFG
The ALIBI ALI-BC700 series indoor/outdoor bullet cameras include a new generation sensor with high
sensitivity and advanced circuit design technology. They feature high resolution, low image distortion and
low noise features which makes them suitable for both surveillance and image processing systems.
Features
• High resolution color sensor: 700 TV Lines
• 2.8 - 12 mm Varifocal lens (ALI-BC700VFG only)
• 12 Vdc power
• IR LED enables the day/night surveillance
• IR cut lter auto switch
• True day/night
• High color rendition
• Weather protection: IP66 rated
Mounting Bracket
Adjustments
Camera body
Mounting base
Lens
IR LED Array
ALI-BC700G Cameras
Mounting base
IR LED ArraySun shield
Integrated
Mounting Bracket
Focus - zoom
adjustments
Vari-focal Lens
(2.8 mm - 12 mm)
ALI-BC700VFG Camera
Power
Connector
Video BNC
Connector
ALI-BC700 series cameras drop cable connectors
2
www.observint.com
ALI-BC700VFG camera typical wall mounting
NOTE
If mounting the camera on a wall, ensure that the label on the mounting base, “Bottom,” is down.
If mounting the camera on a ceiling, orient the mounting base so that the cable guide is pointing
away from any source of water, dust, and other contaminates.
1. Using the drill template provided, mark the location of the screws that anchor the mounting base
to the mounting surface. See the note above. If you are routing the drop cable through mounting
surface, also mark the position of the hole for the drop cable.
2. Drill holes for the screws that anchor the base to the mounting surface. The mounting hardware
provided is appropriate for most surfaces. However, depending on the surface materials, more
appropriate fasteners may be required.
3. Drill a 3/4” hole through the mounting surface for the drop cable, if necessary.
4. Route the drop cable through the hole in the mounting surface, or through the cable guide in the
mounting base, then attach the camera assembly to the surface using the appropriate fasteners.
5. Connect the camera drop cable to video and power extension cables as required.
6. Connect the other end of the video extension cable to a video monitoring device, such as a CCTV
system monitor or DVR.
NOTE
Drop cable connectors are not waterproof.
7. Connect the other end of the power extension cable to a 12 Vdc power source. Observe the polarity
of the cable shown in the photo on page 1 of this guide.
Camera adjustments
1. Apply power to the camera.
2. Verify that video from the camera can be seen on the monitor.
3. While observing video from the camera, loosen the mounting bracket pan, elevation and horizontal
line adjustment lock screws, point the camera at your surveillance target, and then tighten
adjustment lock screws or nuts to hold the camera in position.
For the ALI-BC700G camera: The mounting bracket pan adjustment can be made after loosening
the lock nut (see the photo below). Use a Phillips #1 screwdriver for the elevation and horizontal line
adjustment lock screws.
0° ~ 90°
0° ~ 360°
0° ~ 360°
Use for horizon line
adjustment
Use for pan
adjustment
(lock nut)
Use for
elevation
adjustment
ALI-BC700G camera mounting bracket adjustment
For the ALI-BC700VFG camera: Use Phillips #2 screwdriver for the pan, elevation and horizontal
line adjustment lock screws.
0° ~ 90°
0° ~ 360°
0° ~ 360°
Use for Horizon Line
Adjustment
Use for pan
Adjustment
Use for
Elevation
Adjustment
ALI-BC700VFG camera mounting bracket adjustment
4. Adjust the sun shield (forward or back) to shield the lens from direct light, if necessary.
5. If your camera has a varifocal lens (ALI-BC700VFG only), remove the cover on the underside of the
camera (slide the cover forward to remove) to access the focus and zoom adjustment screws. Use
the tool on the cover to adjust the zoom and focus if needed, and then reinstall the cover.
Focus
adjustment
Zoom
adjustment
Adjustment tool
Cover
ALI-BC700VFG camera Focus - Zoom adjustment
Specications
Model ALI-BC700G ALI-BC700VFG
Image Sensor: 1/3” DIS 1/3” DIS
Signal System: NTSC NTSC
Eective Pixels: 976(H) × 496(V) 976(H) × 496(V)
Min. Illumination: 0.1 lux @ (F1.2, AGC on),
0 lux with IR
0.1 lux @ (F1.2, AGC ON),
0.14 lux @ (F1.4, AGC ON),
0 lux with IR
Shutter Time: 1/30 sec to 1/15,000 sec 1/60 sec to 1/100,000 sec
Lens: 3.6 mm
Angle of view: 68.4° (3.6 mm)
2.8 ~ 12 mm @ F1.4
Angle of view: 80° - 27.2°
Lens Mount: M12 φ14
Adjustment Range: Pan: 0 - 360°, Tilt: 0 -90°, Rotation: 0 - 360° Pan: 0 - 360°, Tilt: 0 - 90°, Rotation: 0 - 360°
Day& Night: IR cut lter with auto switch IR cut lter with auto switch
Horizontal Resolution: 700 TVL 700 TVL
Synchronization: Internal synchronization Internal synchronization
Video Output: 1 Vp-p composite output (75 Ω/BNC) 1 Vp-p composite output (75 Ω/BNC)
S/N Ratio: More than 62 dB More than 62 dB
BLC: On On
Operating Conditions: -40 °F ~ 140 °F (-40 °C ~ 60 °C) -40 °F ~ 140 °F (-40 °C ~ 60 °C)
Humidity: 90% or less (non-condensing) 90% or less (non-condensing)
Power Supply: 12 Vdc ± 10% 12 Vdc ± 10%
Power Consumption: Max. 1.8 W, (Max. 4 W with IR cut lter on) Max. 4 W(Max. 5 W with IR cut lter on)
Weather Proof: IP66 IP66
IR Range: 32 ~ 65 ft (10 ~ 20 m) approx. 98 ~ 131 ft (30 ~ 40 m) approx.
Dimension: Φ2.76" × 5.89" (Φ70 × 149.5 mm) Φ4.13" x 3.42" x 10.52"
(105 × 86.9 × 267.2 mm)
Weight: 0.79 lbs (360 g) 2.97 lbs (1350 g)
© 2014 Observint Technologies. All rights reserved.
3
www.observint.com
© 2014 Observint Technologies. All rights reserved.
Maintenance
Cleaning
Clean the camera dome with an approved glass cleaning solution and a lint free cloth.
• Dust can be removed from the unit by wiping it with a soft damp cloth. To remove stains, gently rub
the surface with a soft cloth moistened with a mild detergent solution, then rinse and dry it with a
soft cloth.
• Remove all foreign particles, such as plastic or rubber materials, attached to the camera housing.
These may cause damage to the surface over time.
CAUTION
Do not use benzene, thinner or other chemical products on the camera assembly; these may
dissolve the paint and promote damage of the surfaces. Before using any chemical product,
carefully follow the accompanying instructions.
Troubleshooting
Problem Possible Cause
Nothing appears on the screen - Check the power connection.
- Check the video signal cable connection to the monitor.
The video image is dim or not clear. - If the camera lens is dirty, clean it with a soft, clean cloth.
- Adjust the monitor controls, if necessary.
- If the camera is facing a very strong light, change the camera position.
- Adjust the lens focus.
The screen is dark. - Adjust the contrast control of the monitor.
- If you have an intermediate device, set the impedance (75 Ω /Hi-Z)
properly, and check the cable connections.
The camera is not working properly and the
surface of the camera is hot.
- Verify that the camera is correctly connected to an appropriate regulated
power source.
The image on the monitor ickers - Make sure that the camera isn’t facing direct sunlight or uorescent light.
If necessary,change the camera position.
  • Page 1 1
  • Page 2 2
  • Page 3 3

ALIBI ALI-BC700G Quick Installation Manual

ALIBI
Brand
ALIBI
Model
ALI-BC700G
Category
Security cameras
Type
Quick Installation Manual
Download PDF
report

Ask a question and I''ll find the answer in the document

Finding information in a document is now easier with AI

Related papers

Other documents