ALIBI ALI-TS1012R Quick Installation Manual
- Category
- Security cameras
- Type
- Quick Installation Manual
ALIBI ALI-TS1012R is a 2MP indoor dome camera with a high-performance CMOS sensor and advanced circuit design technology. It features high resolution, low image distortion, and low noise, making it suitable for surveillance and image processing systems. The camera has a 2.8mm lens and supports true day/night functionality, providing clear images even in low-light conditions. With its Smart IR technology, the camera can provide up to 65ft of IR distance, ensuring clear nighttime vision. The camera requires an Alibi HD-TVI compatible recorder (HD-TVI DVR) for operation.
ALIBI ALI-TS1012R is a 2MP indoor dome camera with a high-performance CMOS sensor and advanced circuit design technology. It features high resolution, low image distortion, and low noise, making it suitable for surveillance and image processing systems. The camera has a 2.8mm lens and supports true day/night functionality, providing clear images even in low-light conditions. With its Smart IR technology, the camera can provide up to 65ft of IR distance, ensuring clear nighttime vision. The camera requires an Alibi HD-TVI compatible recorder (HD-TVI DVR) for operation.
1
www.observint.com
ALI-TS1012 R_CQ
161004
During installation:
• Camera Lens: Handle the camera carefully to prevent scratching or soiling the lens. If the lens
becomes soiled or oily, IR can reect back onto the lens. See the
Cleaning Instructions at the end of
this document for more information.
• Power supply: Camera drop cable: The camera drop cable includes two connectors:
— Video BNC connector: For transmission of the HD-TVI video signal across a coax (75 Ω)
extension cable.
— Power connector: When applying Vdc power, observe the power polarity. See the drop cable
photo above for the connector polarity conguration.
Step 1. Mounting the camera
These cameras can be mounted on a wall or ceiling that has sucient strength to support it. The video/
power drop cable from the camera can be routed either through mounting surface or through a cable guide
on the edge of the mounting base.
CAUTION
Use extra care to avoid touching or soiling the clear plastic of the dome. Oils on the surface
can cause IR reections back onto the camera lens. See the Cleaning Instructions included
at the end of this document.
1. Use a blade screwdriver to separate the mounting base from the dome assembly.
Pry Slot
2. Using the drill template or the mounting base, mark the holes for the camera mounting screws.
3. Drill holes for the screws that anchor the base to the mounting surface. The mounting hardware
provided is appropriate for most surfaces. However, depending on the surface material and strength,
more appropriate fasteners may be required.
4. Drill a 3/4” hole through the mounting surface for the drop cable, if necessary.
5. If using wall inserts for the mounting screws, install the wall inserts at this time.
6. Route the camera drop cable through a cable guide, or through the hole in the mounting surface,
and then secure the mounting base to the surface with two screws. .
7. Connect the camera drop cable to video and power extension cables.
ALI-TS1012R HD-TVI 2MP Indoor Dome
Camera Quick Installation Guide
The ALIBI ALI-TS1012R dome camera include a new generation sensor with high sensitivity and advanced
circuit design technology. They feature high resolution, low image distortion and low noise features which
makes them suitable for surveillance and image processing systems.
Features
• 2 Megapixel high-performance CMOS
• HD-TVI HD output, up to 2MP resolution
• 2.8 mm lens
• True Day/Night
• Smart IR up to 65 ft IR distanc
• Requires Alibi HD-TVI compatible recorder (HD-TVI DVR)
Cable
guide
Pry Slot
Mounting
base
Dome
assembly
Lens
IR LED
array
Power
Connector
HD-TVI video
BNC connector
Camera drop cable connectors
What’s in the box
• Camera assembly
• Mounting hardware
• This instruction guide
• Drill template
Tools you need
To install the camera, you will need:
• 12 Vdc power source. See Specications for powering requirements.
• Tools and additional fasteners (may be required) for mounting the camera
• Video and power extension cable
Installation
Before installation:
• Make sure that the device is in good condition and all the assembly parts are included.
• Check the specication of the products for the installation environment.
• Make sure that the wall or the ceiling is strong enough to withstand 3 times the weight of the camera.
• To avoid re or shock hazard, use only UL listed power supplies. Verify that the power supply will
provide the rated voltage and wattage for the camera. See the Specications section.
2 www.observint.com
8. Connect the other end of the video extension cable to a video monitoring device, such as a
compatible HD-TVI capable DVR.
NOTE
Drop cable connectors are not waterproof.
9. Connect the other end of the power extension cable to a 12 Vdc power source. Observe the polarity
of the cable shown in the photo on page 1 of this guide.
Step 2. Camera adjustments
1. Apply power to the camera.
2. Verify that video from the camera can be seen on a HD-TVI DVR monitor.
3. While observing video from the camera, adjust camera pan, tilt and rotation to point the camera at
your surveillance target.
Pan adjustment (0 ~ 360˚) Tilt adjustment (0 ~ 75˚)
Rotation adjustment (0 ~ 360˚)
4. Ensure the dome assembly is clean (see Cleaning Instructions at the end of this document), and
then reinstall the dome.
Cleaning Instructions
• Dust or grease on the dome cover will cause IR reection. Do not remove the dome cover lm until the
installation is nished. If there is dust or grease on the dome cover, clean the dome cover with clean
soft cloth and isopropyl alcohol.
• Make sure that there is no reective surface too close to the camera lens. The IR light from the camera
may reect back into the lens causing reection.
• The foam ring around the lens must be seated ush against the inner surface of the bubble to isolate
the lens from the IR LEDS. Fasten the dome cover to camera body so that the foam ring and the dome
cover are attached seamlessly.
Clean the camera dome with an approved glass cleaning solution and a lint free cloth.
• Dust can be removed from the unit by wiping it with a soft damp cloth. To remove stains, gently rub
the surface with a soft cloth moistened with a mild detergent solution, then rinse and dry it with a
soft cloth.
• Remove all foreign particles, such as plastic or rubber materials, attached to the camera housing.
These may cause damage to the surface over time.
CAUTION
Do not use benzene, thinner or other chemical products on the camera assembly; these may
dissolve the paint and promote damage of the surfaces. Before using any chemical product,
carefully follow the accompanying instructions.
Specications
Camera
Image Sensor 2MP CMOS Image Sensor
Eective Pixels 1920(H)*1080(V)
Min. illumination 0.01 Lux @ (F1.2,AGC ON),0 Lux with IR
Shutter Time 1/30 s to 1/50,000 ss
Lens 2.8 mm @ F1.2
Lens Mount M12
Day & Night ICR
Angle Adjustment Pan: 0° ~ 360°; Tilt: 0° ~ 75°; Rotate: 0° ~ 360°
Synchronization Internal Synchronization
Video Frame Rate 1080p @ 30 fps
HD Video Output 1 Analog HD output
S/N Ratio > 62 dB
General
Operating Conditions -4 °F ~ 113 °F (-20 °C ~ 45 °C ), Humidity 90% or less
(non-condensing)
Power Supply 12 Vdc ± 15%
Power Consumption Max. 4 W
IR Range 65 ft (20 m)
Communication Up the coax
Dimensions φ 3.86” × 2.57” (φ98 mm × 65.4 mm)
Weight Approx. 0.77 lb (250 g)
Troubleshooting
Problem Possible Cause
Nothing appears on the screen - Check the power connection.
- Check the video signal cable connection to the monitor.
The video image is dim or not clear. - If the camera lens is dirty, clean it with a soft, clean cloth.
- Adjust the monitor controls, if necessary.
- If the camera is facing a very strong light, change the camera position.
- Adjust the lens focus.
The screen is dark. - Adjust the contrast control of the monitor.
- If you have an intermediate device, set the impedance (75 Ω /Hi-Z)
properly, and check the cable connections.
The camera is not working properly and the
surface of the camera is hot.
- Verify that the camera is correctly connected to an appropriate regulated
power source.
The image on the monitor ickers - Make sure that the camera isn’t facing direct sunlight or uorescent light.
If necessary,change the camera position.
© 2016 Observint Technologies. All rights reserved.
-
1
-
2
ALIBI ALI-TS1012R Quick Installation Manual
- Category
- Security cameras
- Type
- Quick Installation Manual
ALIBI ALI-TS1012R is a 2MP indoor dome camera with a high-performance CMOS sensor and advanced circuit design technology. It features high resolution, low image distortion, and low noise, making it suitable for surveillance and image processing systems. The camera has a 2.8mm lens and supports true day/night functionality, providing clear images even in low-light conditions. With its Smart IR technology, the camera can provide up to 65ft of IR distance, ensuring clear nighttime vision. The camera requires an Alibi HD-TVI compatible recorder (HD-TVI DVR) for operation.
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
ALIBI ALI-TS1012VR Quick Installation Manual
-
-
-
-
-
-
ALIBI ALI-TS2015R Quick Installation Manual
-
-
-
ALIBI ALI-TS1025R Quick Installation Manual