ALIBI ALI-TP3023R Quick Installation Manual

Brand: ALIBI

Model: ALI-TP3023R

Category: Security cameras

Type: Quick Installation Manual

www.observint.com

ALI-TP3023R_CQ

160929

• To avoid re or shock hazard, use only UL listed power supplies. Verify that the power supply will

provide the rated voltage and wattage for the camera. See the Specications section.

During installation:

• Camera Lens: Handle the camera carefully to prevent scratching or soiling the lens. If the lens or IR

array shield becomes soiled, clean it only with approved products. See the

Cleaning section.

• Power supply: Camera drop cable: The camera drop cable includes two connectors:

— Video BNC connector: For transmission of the video signal across a coax (75 Ω) extension

cable to an HD-TVI compatible recorder.

— Power connector: When applying power, observe the power polarity. See the picture to the

left for the connector polarity conguration.

Mounting the camera

An ALI-TP3023R camera can be mounted directly to a wall or ceiling, or with a junction box. The surface

should support at least three times the weight of the camera and junction box (if used). The video/power

drop cable from the camera can be routed either through mounting surface or through a cable channel in

the mounting base.

• Mounting the camera directly to a wall or ceiling

Typical ceiling mounting

NOTE

If mounting the camera on a wall, ensure that the cable channel in the mounting base is down.

If mounting the camera on a ceiling, orient the mounting base so that the cable channel is pointing

away from any source of water, dust, and other contaminates.

1. Using the drill template provided, mark the location of the screws that anchor the mounting base

to the mounting surface. See the note above. If you are routing the drop cable through mounting

surface, also mark the position of the hole for the drop cable.

2. Drill holes for the screws that anchor the base to the mounting surface. The mounting hardware

provided is appropriate for most surfaces. However, depending on the surface materials, more

appropriate fasteners may be required.

3. If routing the drop cable through the mounting surface, drill a 5/8” hole in the middle of the drill

template.

4. Route the drop cable through the hole in the mounting surface, or through the cable channel in the

mounting base, then attach the camera assembly to the surface using the appropriate fasteners.

5. Connect the camera drop cable to video and power extension cables as required.

6. Connect the other end of the video extension cable to an HD-TVI compatible video monitoring

device (QVR) digital video recorder.

NOTE

Drop cable connectors are not waterproof.

7. Connect the other end of the power extension cable to a 12 Vdc power source. Observe the polarity

of the cable shown in the photo on page 1 of this guide.

• Mounting the camera with a junction box

The ALI-AJ6 junction box is shown below. It can be attached to a wall or ceiling. Video and power

extension cables can be routed in through the opening in the back of the box or through the conduit

coupling, and attached to the camera drop cables inside the enclosure.

ALI-TP3023R 3MP HD-TVI 260’ IR

Outdoor Bullet Camera

Quick Installation Guide

The ALIBI ALI-TP3023R indoor/outdoor HD-TVI bullet cameras include a high sensitivity sensor with the

ability to send HD video across standard coaxial cable. This camera features:

• 3 MP Megapixel High Performance CMOS

• 260’ Smart Full Frame IR

• 2.8 mm wide angle lens with an 84˚ eld of view covers a large area

• WDR Wide Dynamic Range 120 dB

• Up the Coax (UTC) technology for OSD control

• -40° to 140°F temperature range

• IP66 Weather Rated Housing

• Compatible with ALI-QVR4000/5000/7000 Series recorders (QVR)

• Can be installed with optional ALI-AJ6 junction box.

Adjustable

sun shield

Camera body

Mounting

base

Lens

IR LED

Adjustable

mounting

bracket

ALI-TP3023R camera

Power

Connector

HD-TVI video

BNC connector

Camera drop cable connectors

What’s in the box

• Camera assembly

• Mounting hardware

• Drill template

• This instruction guide

What you need

To install the camera, you will need:

• 12 Vdc power source. See Specications for wattage requirement.

• Tools and additional fasteners (may be required) for mounting the camera

• Phillips #2 screwdriver

• Video and power extension cable

• HD-TVI video setup monitor (optional)

Installation

Before installation:

• Make sure that the device is in good condition and all the assembly parts are included.

• Check the specication of the products for the installation environment.

• Make sure that the wall or the ceiling is strong enough to withstand 3 times the weight of the camera.

2 www.observint.com

Front

plate

Box

Conduit

coupling/

cable

channel

Back

“UP”

label

Holes for

mounting

screws (3)

Holes for

mounting

base

screws (6)

To use the junction box:

1. Remove the ALI-AJ6 front plate from the box by removing the three screws (see above).

2. Attach the front plate to the camera mounting base using three screws. If the box will be wall

attached to a wall, ensure that the “UP” label on the mounting plate is at the top of the camera, and

the cable channel in the camera mounting base is toward the bottom of the camera.

3. Using the ALI-AJ6 box as a guide, mark and then drill three holes for the screws that will attach the

box to the wall or ceiling. If the extension cables will be routed into the box through the mounting

surface, also drill a hole for the extension cables.

4. Attach the box to a wall or ceiling with three screws. Ensure that the wall or ceiling will support at

least three times the weight of the camera with the junction box.

5. Route the video and power extension cables into the box.

6. Attach the video and power extension cable to the camera drop cables. Observe the polarity of the

power cable connector as shown on page 1 of this guide.

7. Reattach the ALI-AJ6 front plate (with the camera) to the box.

Camera adjustments

1. Apply power to the camera.

2. Verify that video from the camera can be seen on the monitor.

3. While observing video from the camera, loosen the mounting bracket pan lock nut, and elevation

and horizontal line adjustment lock screws, point the camera at your surveillance target, and then

tighten adjustment lock screws and nut to hold the camera in position.

0° ~ 180°

0° ~ 360°

Rotation: Use for horizon line

adjustment 0° ~ 360°

Pan lock

nut: loosen

for pan

adjustment

Tilt: Use for

elevation

adjustment

Mounting bracket adjustment

Step 1. Open the OSD menu

The On Screen Display (OSD) provides conguration options for rening the performance of the camera.

It also can be used to block sensitive portions in the eld of view (Privacy). You can open the OSD menu

system from either the QVR Live View display or through remote login to the ALIBI recorder.

Opening the OSD Menu through the QVR

To open the OSD menu on the QVR monitor:

1. Open the QVR Live View screen, and then click inside the screen where the PTZ camera video image

is displayed. See below.

2. Click the PTZ Control icon in the Quick Setting Toolbar. The PTZ camera Live View window will

expand to full screen and the pop-up window shown below will open.

Menu icon

3. In the PTZ Control panel pop-up window, click the Menu icon on the Conguration line.

4. Drag the PTZ Control window to a position where it doesn’t cover the OSD menu (such as the left

side).

NOTE

The PTZ Control window direction buttons and the Iris + and Iris - keys are used to navigate the

OSD menu and set conguration options in the camera. See “OSD Denitions: On-screen Display

(OSD) menus” on page 3.

Opening the OSD Menu through remote login to the QVR

To open the OSD menu during a remote login to the recorder:

1. After logging into the QVR, open the camera in a single Live View window.

www.observint.com

2. In the PTZ control panel, scroll down the Preset list to Preset95, click the entry to highlight it, and

then click the Call icon. See below. The OSD MAIN MENU screen will open.

PTZ control panelPreset95 Call icon

NOTE

The PTZ control panel direction buttons and the Iris + and Iris - keys are used to navigate the

OSD menu and set conguration options in the camera.

OSD menu navigation

For the ALIBI Recorder: Navigation and settings in the OSD are made through direction keys and the Iris

+ and Iris - buttons in the ALIBI QVR PTZ Control panel. See below.

Direction keys Iris+ Iris–

Iris+ Iris–

Direction keys

ALIBI QVR PTZ Control panel ALIBI QVR remote access PTZ control panel

For remote access to the ALIBI QVR: Navigation and settings in the OSD are made through direction

keys and the Iris + and Iris - buttons in the ALIBI QVR PTZ control panel. See above.

The function of the directional keys and Iris buttons are dened in the table below.

Keys Function

Move up in the parameter list

Move down in the parameter list.

Move to previous page, eld, or move the camera left.

Keys Function

Move to next page, eld, or move eld right.

Iris+ (OPEN) Set parameter value, or open sub-menu

Iris– (CLOSE) Cancel change of parameter.

OSD Denitions: On-screen Display (OSD) menus

After the camera is installed on a compatible recorder, you can open the OSD menu clicking the PTZ Control

icon on the Quick Setting Toolbar.

To navigate the OSD menu and select options:

• Move the cursor up/down to select the menu item.

• Move the cursor left/right to adjust the value of the selected item.

• Click the OK key to conrm a selection.

FORMAT menu

Move the cursor to FORMAT, and click the menu button to enter the FORMAT sub-menu to select the

format of camera. Camera settings in the recorder must match the option selected in the camera.

MAIN MENU

AE (Auto Exposure)

AE describes the brightness-related parameters. You can adjust the image brightness by the BRIGHTNESS,

EXPOSURE MODE, and GAIN in dierent light conditions.

• BRIGHTNESS: Brightness refers to the brightness of the image. You can set the brightness value from

1 to 10 to darken or brighten the image. The higher the brightness value, the brighter the image.

• EXPOSURE MODE: You can set AE mode as GLOBAL, BLC, and WDR.

— GLOBAL: GLOBAL refers to the normal exposure mode, used when adjusting for unusual lighting

distribution, variations, non-standard processing, or conditions of under exposure to get an

optimum image.

— BLC (Backlight Compensation): BLC compensates light to the object in the front to make it clear,

while compensating for over-exposure of the background where the light is strong. The level can

be adjusted from 0 to 8.

— WDR (Wide Dynamic Range): The wide dynamic range (WDR) function helps the camera

provide clear images even under back light circumstances. WDR balances the brightness level of

the whole image and provide clear images with details.

www.observint.com

• GAIN: Optimizes the clarity of image in poor light. GAIN level can be set to HIGH, MIDDLE, and LOW.

Select OFF to disable the GAIN function. Noise is amplied when GAIN is on.

WB (White Balance)

White balance is the white rendition function of the camera to adjust the color temperature according to

the environment. It can remove unrealistic color casts in the image. You can set WB mode as either ATW

or MWB.

• ATW: In ATW mode, white balance is adjusted automatically according to the color temperature of the

scene illumination.

• MWB: In MWB mode, you can set the R GAIN/B GAIN value from 0 to 255 to adjust the shades of red/

blue color of the image.

DAY-NIGHT

Color, B/W, and SMART are selectable for DAY and NIGHT switches.

• COLOR: The image is colored in day mode all the time.

• B/W: The image is black and white all the time, and the IR LED turns on in the low-light conditions.

• SMART: You can select to turn on/o the INFRARED and set the value of SMART IR in this menu.

— INFRARED: Select this option to turn on/o the IR LED in response to the light level in the eld

of view.

— SMART IR: Use the Smart IR feature is to adjust the light to its most suitable intensity, and to

prevent the image from over exposure. The SMART IR value can be adjusted from 0 to 3. The

higher the value, the more obvious the eects are. If set to 0, SMART IR is disabled.

VIDEO SETTING Menu

Move the cursor to VIDEO SETTING and press the conrm button to enter the submenu. In this menu you

can adjust CONTRAST, SHARPNESS, COLOR GAIN, DNR and MIRROR settings.

• CONTRAST: This feature enhances the dierence in color and light between parts of an image. You

can set the CONTRAST value from 1 to 10.

• SHARPNESS: Sharpness determines the amount of detail an imaging system can reproduce. You can

set the SHARPNESS value from 1 to 10.

• COLOR GAIN: Adjust this feature to change the saturation of the color. The value ranges from 1 to 10.

• DNR (Digital Noise Reduction): The DNR function can decrease the noise eect, especially when

capturing moving images in low light conditions and delivering more accurate and sharp image

quality. You can set the DNR value from 1 to 10.

• MIRROR: DEFAULT, H, V, and HV are selectable for mirror.

— DEFAULT: The mirror function is disabled.

— H: The image is reected horizontally.

— V: The image is reected vertically.

— HV: The image is reected both horizontally and vertically.

RESET

• RESET: Reset all the settings to the default.

SAVE &EXIT

• SAVE &EXIT: To save your new settings, move the cursor to SAVE &EXIT and click OK to save the

setting and exit the menu.

Specications

Camera

Image Sensor 3MP CMOS image sensor

Eective Pixels 2052(H) * 1536(V)

Min. illumination 0.01 Lux @ (F1.2,AGC ON), 0 Lux with IR

Shutter Time 1/25 s to 1/50,000 s

Lens 3.6 mm lens @ F1.2

Lens Mount M12

Day & Night ICR

Angle Adjustment Pan: 0° ~ 360°; Tilt: 0° ~ 90°; Rotate: 0° ~ 360°

Synchronization Internal Synchronization

WDR > 120 dB

Video Frame Rate 1920 × 1536 @ 18 fps

HD Video Output 1 Analog HD output

S/N Ratio > 62 dB

AGC Support

D/N Mode Color / BW /SMART

White Balance ATW / MWB

BLC Support

Functions Wide Dynamic Range, Digital noise reduction, Mirror, SMART IR

General

Operating Conditions -40°F ~ 140°F (-40°C ~ 60°C), Humidity 90% or less (non-condensing)

Power Supply 12 Vdc ± 15%

Power Consumption Max. 5 W

Protection Level IP66

IR Range Up to 260 ft (80 m)

Communication Up the coax (HD-TVI output)

Dimensions 3.41" × 3.23” × 8.67”(86.7 mm × 81.6 mm × 226 mm)

Weight 1.5 lb (690 g) approx.

Cleaning

Clean the camera dome with an approved glass cleaning solution and a lint free cloth.

• Dust can be removed from the unit by wiping it with a soft damp cloth. To remove stains, gently rub

the surface with a soft cloth moistened with a mild detergent solution, then rinse and dry it with a

soft cloth.

• Remove all foreign particles, such as plastic or rubber materials, attached to the camera housing.

These may cause damage to the surface over time.

CAUTION



Do not use benzene, thinner or other chemical products on the camera assembly; these may

dissolve the paint and promote damage of the surfaces. Before using any chemical product,

carefully follow the accompanying instructions.

www.observint.com

Troubleshooting

Problem Possible Cause

Nothing appears on the screen - Check the power connection.

- Check the video signal cable connection to the monitor.

- Check QVR camera settings to verify the video resolution mode of the camera

and QVR match

The video image is dim or not clear. - If the camera lens is dirty, clean it with a soft, clean cloth.

- Adjust the monitor controls, if necessary.

- If the camera is facing a very strong light, change the camera position.

- Adjust the lens focus.

The screen is dark. - Adjust the contrast control of the monitor.

- If you have an intermediate device, set the impedance (75 Ω /Hi-Z)

properly, and check the cable connections.

The camera is not working properly and

the surface of the camera is hot.

- Verify that the camera is correctly connected to an appropriate regulated

power source.

The image on the monitor ickers - Make sure that the camera isn’t facing direct sunlight or uorescent light.

If necessary,change the camera position.

ALIBI ALI-TP3023R Quick Installation Manual

Brand: ALIBI

Model: ALI-TP3023R

Category: Security cameras

Type: Quick Installation Manual

Download PDF

report

ALIBI ALI-TP3023R Quick Installation Manual

ALIBI ALI-TP3023R Quick Installation Manual

Related papers

Other documents