© 2002 American Honda Motor Co., Inc - All Rights Reserved. AII 24298 (0212) 1 of 3
08B60-SCV-1000-91
INSTALLATION
INSTRUCTIONS
Accessory Application
Publications No.
Issue Date
DEC 2002
ELEMENT
(DX)
AM/FM CD TUNER
POCKET ATTACHMENT KIT
PARTS LIST
Pocket Attachment Kit
P/N 08B60-SCV-100
Pocket
2 Self-tapping screws,
4 x 12 mm
Radio Attachment Kit
P/N 08B02-SCV-100
Bracket "L"
Bracket "R"
4 Self-tapping screws,
4 x 16 mm
AM/FM CD Tuner
P/N 08A02-4E1-100
AM/FM CD tuner
Owner’s Manual
4 Washer-screw,
5 x 8 mm
TOOLS REQUIRED
Phillips screwdriver
Flat-tip screwdriver
Shop towel
AII 24298
www.HandA-Accessories.com
Not Used
4 washer screws
5 x 16 mm
2 of 3 AII 24298 (0212) © 2002 American Honda Motor Co., Inc - All Rights Reserved.
1. Wrap a shop towel around the top of a flat-tip
screwdriver and insert it into the grooves of the
audio panel. Pull the audio panel out toward you to
release the five clips and remove the audio panel.
Take care not to damage the clips and the audio
panel. Disconnect the antenna lead and the 20-pin
connector from the rear of the cover.
3. Push the front of the pocket from above and below
and hold for one minute to fix the shape.
4. Position the audio unit on the pocket and install
the two brackets with the four 5 x 8 mm washer-
bolts and two 4 x 12 mm self-tapping screws.
2. Remove and discard the cover from the audio
panel (four tabs).
2008060K
PUSHDOWN
PUSHUP
POCKET
Customer Information: The information in this
installation instruction is intended for use only by
skilled technicians who have the proper tools,
equipment, and training to correctly and safely add
equipment to your vehicle. These procedures
should not be attempted by “do-it-yourselfers.”
INSTALLATION
2828202K
GROOVES IN
AUDIO PANEL
CLIPS (5)
AUDIO
PANEL
COVER
ANTENNA
LEAD
VEHICLE 20-PIN
CONNECTOR
FLAT-TIP
SCREWDRIVER
2018030K
RETAINING
TAB
COVER
(Not reused.)
RETAINING
TAB
AUDIO
PANEL
2625021K
AUDIO
UNIT
5 x 8 mm
WASHER-
SCREW
4 x 12 mm
SELF-
TAPPING
SCREW
POCKET
Insert the
boss on the
pocket with
this hole.
Use the
upper hole.
5 x 8 mm
WASHER-
SCREW
4 x 12 mm
SELF-
TAPPING
SCREW
Use the
lower
hole
BRACKET
"R"
BRACKET
"L"
Tighten with a screw
while pushing the
front of the pocket in
upward direction.
© 2002 American Honda Motor Co., Inc - All Rights Reserved. AII 24298 (0212) 3 of 3
Installing the Audio Unit and Pocket Assembly
5. While holding the audio unit close to the center
panel opening, plug the vehicle 20-pin connector
and antenna lead into the back of the audio unit.
6. Slide the audio unit and pocket assembly into the
center panel opening and install the four
4 x 16 mm self-tapping screws.
7. Turn the ignition key on, and enter the radio
anti-theft code.
8. Check the operation of the audio unit as described
in the Owner’s Manual supplied.
9. Set the radio clock.
10. Reinstall all removed parts.
11. Put the AM/FM CD Tuner Owner’s Manual in the
glove box.
2828210K
VEHICLE 20-PIN
CONNECTOR
ANTENNA LEAD
4 x 16 mm
SELF-TAPPING
SCREWS
AUDIO
UNIT
XXXXXXXXXXX
XXXXXXXXXXX
XXXXXXXXXXX
use the 5 x 16 screws that
were included separately,
not the 4 x 16 self tapping
ones
XXXXXXXXXXXXXXXXXXXXXXXXX 5 x 16 screws
-
1
-
2
-
3
Ask a question and I''ll find the answer in the document
Finding information in a document is now easier with AI
Related papers
-
Honda 08A02-4E1-100 Installation guide
-
-
-
-
-
-
-
-
-
Other documents
-
JAXJOX JJ15002 User manual
-
Acura 08E02-S6M-200 Installation Instructions Manual
-
CTA Digital WI-PUB Datasheet
-
Acura 08A26-1B2-101 User manual
-
-
-
-
-
-
Rosemount 6081-P Wireless pH/ORP Transmitter Abridged Owner's manual
