Acrosser Technology AR-ES0631ET Owner's manual

Brand: Acrosser Technology

Model: AR-ES0631ET

Type: Owner's manual

Acrosser Technology AR-ES0631ET features a powerful AMD Geode LX800 processor and many capabilities that make it suitable for use in challenging conditions, including extreme temperatures (-40℃ to +75℃).

It includes one network controller, a fully integrated 10/100BASE-TX solution with high performance networking functions. The AR-ES0631ET also includes one 200-pin SO-DIMM DDR socket, four on-board serial ports, and four USB ports, making it suitable for use in a wide variety of applications even in the harshest unmanned environments.

AR-ES0631ET Installation Guide

ACROSSER

AR-ES0631ET (Extended Temperature)

CRT, LCD, LAN, USB2.0, PCI/104

Installation Guide

Edition: 1.0

AR-ES0631ET Installation Guide

Contents

Introduction of AR-ES0631ET………..………………………………

1.1 Product Outlines

1.2 Packing List

Procedure of Assembly/Disassembly cables from the board……..

2-1 Installing the 2.5”Hard Disk Drive(HDD)………………………...

2-2 Installing an memory card to AR-ES0631………………………

2-3 Inserting a Compact Flash Card…………………………………

Appendix…………………………………

LVDS connector pin assignment……………………………………..

Power connector pin assignment…………………………………….

COM1 to COM4 connector pin assignment…………………………

AR-ES0631ET Installation Guide

1. Introduction of AR-ES0631ET

Welcome to the AR-ES0631ET wide-range temperature product, in which a Single Board

Computer with low power AMD Geode LX800 processor designed-in. The system is

designed for extreme environment with of operating range from -40℃ to +75℃. For this

product feature, AR-ES0631ET can make a lot of outdoor applications available, such as

Traffic Control, Vehicle Computer, Remote Workstation, Outdoor Data Acquisition,

Aviation or Military industries.

ACROSSER’s Extended temperature products are almost choosing the wide operating

temperature components (compliance with Industrial standard in operating temperature)

onboard. This platform has fully loaded and pass robust thermal cycling tested. It is a

reliable, long life time and cost effective extended temperature solution for diverse

applications.

In addition, the AR-ES0631ET provides on chip VGA. The VGA, which provides up to

1920x1440x32bpp at 85Hz and 1600x1200x32bpp at 100HZ resolutions. The VGA

memory is shared with the main memory (2M, 4M, or 8M). AR-ES0631ET also has

18-bit LVDS function in the system, which the resolution up to 1600x1200x32bpp at

60Hz.

The AR-ES01631ET is loaded with special on-board features that rival full-size systems.

It has one network controller on board, uses Realtek RTL8100BL LAN controller, a fully

integrated 10/100BASE-TX solution with high performance networking functions.

Supports Compact Flash™ Type II interface. Plus optional support for AC97 sound with

CD-input. The AR-ES0631ET also includes one 200-pin SO-DIMM DDR sockets for up

to 1GB total on-board memory. The AR-ES0631ET has four on-board serial ports; COM1

with RS232C, COM2, COM3 and COM4 with RS232C, 4 USB ports, and tough

industrial grade construction. All these features make the AR-ES0631ET a very "system

integrator friendly" solution, perfect for handling applications in the harshest unmanned

environments.

AR-ES0631ET Installation Guide

1.1 Product Outlines

Description AR-ES0631ET Serial

CPU Board AR-B1631ET series

Dimensions

250×117×59 (mm)

AR-ES1631ET product outlines

AR-ES0631ET Installation Guide

1.2 Packing List

Description Q’ty

AR-ES0631ET

Power Core/ Adapter 1

IDE Cable 1

Others Screws 4

Mounting Bracket (+screw) 2

AR-ES0631ET Installation Guide

2. Procedure of Assembly/Disassembly

2-1 Installing the 2.5”Hard Disk Drive (HDD)

The following are step-by-step installation

1. Insert the anti-vibration rubbers into the four edge of HDD bracket bay

2. Connect the IDE cable to the 44-pin header of HDD

3. Put the HDD on the HDD bracket and screw them together via four

screws

4. Remove the CPU board out from the AR-ES0631ET for installing the HDD

module later

Fig.1 HDD bracket bay

5. Remove the back cover of AR-ES0631ET by unlocking the two screws

Fig.2 Back cover

Unlock the

screws

AR-ES0631ET Installation Guide

6. Place the HDD module into the space as shown in Fig. 3 and assemble

them together with the case via the fire screws

Fig 3 Install HDD module into AR-ES0631ET

AR-ES0631ET Installation Guide

2-2 Installing an memory card to AR-ES0631ET

The following are step-by-step installation

1. Remove the power cord out from the AR-ES0631ET

2. Unlock the four screws on the top case of AR-ES0631ET, as shown in

Fig.4

Fig. 4 Unlock the top case

3. Unlock the four screws from the front panel and back panel as shown in

Fig.5

Fig.5 Unlock screws from the front/rear panel

AR-ES0631ET Installation Guide

4. Remove the IDE cable out front the CPU board (if you had a HDD

module installed)

5. Unlock the four screws of CPU board out from the AR-ES0631ET as

shown in Fig. 6

Fig.6 Remove the HDD cable out from the CPU board

6. Remove the CPU board out from the AR-ES0631ET as shown in Fig. 7

Fig. 7 Remove the CPU board

AR-ES0631ET Installation Guide

7. Plug the memory card into the socket as shown in Fig. 8

Memory card

Fig.8 Install the memory card into the memory socket

8. Put the CPU board back and screw it on the AR-ES0631ET bottom case

as shown in Fig. 9

Fig.9 Back CPU board into the AR-ES0631ET

AR-ES0631ET Installation Guide

9. Re-connect the IDE cable to CPU board as shown in Fig. 10

Fig. 10 Re-connect IDE cable to the CPU board

10. Back the top cover to the AR-ES0631ET and tight-up with four screws

Fig. 15 back the top cover

11. Tight the four screws on front panel and back panel as shown in Fig.11

Fig. 11 Tight the screw on the front panel

AR-ES0631ET Installation Guide

2-3 Installing a Compact Flash Card

The following are step-by-step installation

1. Remove the power Cord out from the AR-ES0631ET

2. Unlock the two screws from the CF door located on the front panel of

AR-ES0631ET as shown in Fig. 12

Fig.12 Unlock the screw from the CF door

3. Remove the CF holder

4. Place a Compact Flash card with OS or application program inside into

the CF holder as shown in Fig. 13

Fig.13 Inset the CF card into the CF holder

AR-ES0631ET Installation Guide

5. Back the CF module to the CF door and lock the CF door with 2 screws to

the front panel as shown in Fig 14

Fig. 14 Back the CF module to AR-ES0631ET

AR-ES0631ET Installation Guide

Appendix

LVDS connector pin assignment

LVDS connector Pin Assignment

Pin Description

1 VCC

14 CLK-

2 VCC

15 CLK+

3 NC

16 GND

4 NC

17 NC

5 Y0-

18 NC

6 Y0+

19 NC

7 GND

20 VCC12

8 Y1-

21 VCC12

9 Y1+

22 GND

10 GND

23 BKLEN

11 Y2-

24 GND

12 Y2+

25 BKLTCTL

13 GND

AR-ES0631ET Installation Guide

Power connector pin assignment

LVDS connector Pin Assignment

Pin Description Pin Description

12V 3 GND

2 12V 4 GND

COM1 to COM4 connector pin assignment

Pin Description

NDCD NRX

NTX NDTR

2 7

GND NDSR

3 8

NRTS NCTS

4 9

NRIA_12V NC

5 10

* NRIA_12V: Please see AR-B1631 manual for detail data.

Acrosser Technology AR-ES0631ET Owner's manual

Brand: Acrosser Technology

Model: AR-ES0631ET

Type: Owner's manual

Download PDF

report

Acrosser Technology AR-ES0631ET Owner's manual

Acrosser Technology AR-ES0631ET Owner's manual

Related papers

Other documents